Clarke CAX10TP Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

GC0119 - ISS 2

10 TONNE AXLE STAND

MODEL NO: CAX10TP

PART NO: 7600090

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS - ALWAYS READ BEFORE USE

• Read these instructions carefully before use.

• Do not exceed the axle stands maximum

load (10 tonnes), The vehicle weight will be in

the owners manual.

• Use only as specified in this manual.

• NEVER let children play in or around a vehicle

that is on axle stands.

• ALWAYS make sure that before you work

below the vehicle, a responsible person is

aware in case of injury or accident.

• Do not use more than one pair of axle stands.

• Replace the warning label if it becomes

unreadable.

• Use only on a hard, flat surface for example

concrete.

• Make sure that you chock all the wheels that

remain on the ground.

• Make sure that the supported vehicle cannot

move.

• Set each axle stand below an appropriate

point on the vehicle - See your vehicle

owners manual for advice.

• Take care when using the axle stands on a

three-wheeled vehicle or trailer.

• Upper and lower columns are to be used as a

pair as supplied.

• Use stands as a matched pair to support one end of a vehicle only.

• For your safety, do not modify these axle stands.

WARNING: USE ONLY ON A HARD, FLAT SURFACE FOR EXAMPLE

CONCRETE.

WARNING: NEVER WORK UNDER A VEHICLE SUPPORTED ONLY BY A JACK.

WARNING: AFTER LIFTING THE VEHICLE, SUPPORT IMMEDIATELY WITH

PROPERLY RATED AXLE STANDS

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

USING THE AXLE STAND

1. Refer to the vehicle handbook for

the correct jacking procedure and

location of support points.

ADJUST THE AXLE STAND

1. Remove the locating pin (if fitted).

2. Raise the upper column to the

required height and fit the locating

pin into the lowest hole visable.

3. Fit the retaining pin into the end of

the locating pin to secure it in place.

4. Position the axle stand under a

suitable supporting point. See you

vehicle manual for the location.

LOWERING THE VEHICLE

1. Slowly lower the vehicle onto the

centre of the saddle.

REMOVE THE AXLE STANDS

1. Raise the vehicle clear of the axle stands and remove the stands.Ensure

that all tools, equipment and personnel are clear before carefully lowering

the vehicle to the ground.

WARNING: BEFORE USE, MAKE SURE THAT THERE IS NO DAMAGE TO ANY

PART OF THE AXLE STAND, IF THERE IS, DO NOT USE THE AXLE STAND.

WARNING: IT MUST BE ENSURED THAT THE VEHICLE/LOAD IS CAREFULLY

LOCATED ONTO THE CENTRE OF THE AXLE STAND SADDLE. FAILURE TO DO

THIS CAN RESULT IN DAMAGE TO THE AXLE STANDS, LOSS OF SUPPORT TO

THE LOAD, SERIOUS PERSONAL INJURY OR LOSS OF LIFE.

WARNING: DO NOT EXCEED THE RATED LOAD OF 10 TONNES.

WARNING: USE ONLY ON A HARD, FLAT SURFACE, E.G. CONCRETE.

WARNING: DO NOT LOAD THE STANDS OFF CENTRE. FAILURE TO HEED THIS

WARNING MAY CAUSE DAMAGE, INJURY OR LOSS OF LIFE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights

SPECIFICATION

Maximum Height 750 mm

Minimum Height 450 mm

Maximum Load 10 Tonnes per stand

Product Weight 20 kg

Number of Height Positions 5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Baumaschinen Handbücher

Clarke

Clarke CAX10TPB Bedienungsanleitung

Clarke

Clarke Contractor CCM125D Bedienungsanleitung

Clarke

Clarke Strong-Arm CFC1000B Betriebsanleitung

Clarke

Clarke CHT401 Bedienungsanleitung

Clarke

Clarke WOODWORKER CTS17 Bedienungsanleitung

Clarke

Clarke CAX2TF Bedienungsanleitung

Clarke

Clarke Strong Arm CCB1B Bedienungsanleitung

Clarke

Clarke Strong-Arm CFC1000LR Betriebsanleitung

Clarke

Clarke CAX3TP Bedienungsanleitung

Clarke

Clarke APS-1830 Installationsanleitung

Clarke

Clarke Strong-Arm CFC2000B Betriebsanleitung

Clarke

Clarke CHV12 Bedienungsanleitung

Clarke

Clarke SV1A Bedienungsanleitung

Clarke

Clarke CHT264 Bedienungsanleitung

Clarke

Clarke CFC500F Installations- und Betriebshandbuch

Clarke

Clarke CHT617 Bedienungsanleitung

Clarke

Clarke CAX6TP Bedienungsanleitung

Clarke

Clarke CCM125P Installations- und Betriebshandbuch

Clarke

Clarke Strong Arm CHV12B Bedienungsanleitung

Clarke

Clarke Contractor CCM135 Bedienungsanleitung

Clarke

Clarke Strong-Arm CHC500DF Bedienungsanleitung

Clarke

Clarke ODC8 Bedienungsanleitung

Clarke

Clarke CPP5 Installations- und Betriebshandbuch

Clarke

Clarke CFC2000 Bedienungsanleitung

Beliebte Baumaschinen Handbücher anderer Marken

SASFORKS

SASFORKS EXTREME Bedienungsanleitung

Hailo

Hailo H-50 Bedienungsanleitung

Graco

Graco LineLazer ES 1000 Gebrauchs- und Pflegehandbuch

Greenlee

Greenlee 555RSC Bedienungsanleitung

Manitowoc

Manitowoc Grove CD3340B Bedienungsanleitung

Lux Tools

Lux Tools A-FMR-20 Set Bedienungsanleitung

SIP

SIP 03683 Bedienungsanleitung

Volvo

Volvo L30G Bedienungsanleitung

Grizzly

Grizzly G8712 Bedienungsanleitung

Modulift

Modulift CMOD 12 Bedienungsanleitung

Case

Case DV201 Bedienungsanleitung

Sealey

Sealey SC10.V2 Bedienungsanleitung

Wacker Neuson

Wacker Neuson DT05 Bedienungsanleitung

HYVA

HYVA AMCO VEBA 81 Series Bedienungsanleitung

Atlas Copco

Atlas Copco Dynapac V5100TV Bedienungsanleitung

Toro

Toro 323 Bedienungsanleitung

Manitowoc

Manitowoc National Crane 1400A Bedienungsanleitung

SGS

SGS EC1500 Bedienungsanleitung