Clarke IQ2000S Stücklistenhandbuch

THIS PRODUCT IS FOR

OUTDOOR USE ONLY

ASSEMBLY & OPERATION

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1219 - iSS 3

INFRARED QUARTZ HEATER

MODEL NO: IQ2000S

PART NO: 6939006

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Infrared Heater.

PLEASE NOTE THAT THIS PRODUCT IS FOR OUTDOOR USE ONLY

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

OPERATING PARAMETERS

• It must be operated as prescribed in the operating manual.

• Is not intended to be used for domestic use or for the heating of

habitable areas.

• Is not intended to be used to reach and maintain a certain level of

human thermal comfort within an enclosed space in which the heater is

situated.

• Is not intended to be used in enclosed areas with restricted ventilation.

• Is not for use in areas with high levels of fluctuating drafts.

• Is not intended for warming animals or live stock.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

GENERAL

1. Always read and ensure you fully understand the following precautions

and the hazards associated with this type of heater. Do not allow anyone

who has not read these instructions to operate this heater. Please keep

these instructions in a safe place for future reference.

2. Always check for damage before using the heater. Any damage should

be properly repaired or the part replaced. If in doubt, DO NOT use the

heater and consult your local Clarke dealer.

3. Never carry out any modifications to this product. If experiencing difficulty

of any kind consult your local dealer.

4. Use the heater in accordance with any applicable fire regulations.

OPERATING ENVIRONMENT

1. Never use the heater where petrol, paint thinners or other highly flammable

vapour or where high levels of airborne dust may be present.

2. Disconnect the heater from the power supply when not in use.

3. Never place anything on top of the heater. so as to impede free air flow.

4. Do not expose the heater or power cable to rain or wet conditions. Any

water entering the heater will increase the risk of electric shock. The heater

must be protected from rain.

5. Never locate the heater near combustible materials such as curtains,

furniture etc. Allow a distance of at least 1 metre.

6. Allow a distance of at least 1 metre from an adjacent wall and avoid

installing the heater close to power socket outlets.

7. Do not allow the heating element to become covered with dust which

could become a fire hazard. If used in a dusty workplace it should be

cleaned as described under Cleaning and Maintenance.

8. Never touch the heater element for at least 15 minutes after switching off.

9. Do not leave the heater unattended.

10. Do not use this heater with a programmable timer used to switch it on

automatically.

11. Never attach any duct work to the front of the heater.

12. That this product is for outdoor use only.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PERSONAL SAFETY

1. When the heater is to be operated in the presence of other people the

user is responsible for informing those present of the safety precautions and

of the hazards involved.

2. The heater is not to be used by children or persons with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge.

3. Always ensure that people and animals are a safe distance from the front

of the heater when in operation.

4. This heater will be hot when in operation and should not be touched until it

has fully cooled down after switching off.

5. Never leave the heater plugged in without adult supervision if children or

animals are likely to be present.

ELECTRICAL SAFETY

1. Make sure that the voltage on the rating label is the same voltage as the

power supply. If in doubt consult a qualified electrician.

2. Never modify the plug in any way. Do not use adaptor plugs with earthed

appliances. Correct plugs and outlets will reduce the risk of electric shock.

3. Do not abuse the electrical cable. Keep the cable away from sources of

heat, sharp edges or moving parts. Damaged or tangled cables increase

the risk of electric shock.

4. Regularly inspect the power cable for damage. DO NOT use if damaged &

keep it away from the source of heat. If damaged, it must be replaced.

DAMAGE & REPAIRS

1. If necessary, have your heater repaired by a qualified person using

identical replacement parts to maintain the safety of the heater.

SAFETY SYMBOLS

The above symbols are found on the heater.

Hot surface, do not

touch.

Do not cover.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal which is

marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal which

is marked Lor coloured Red.

• The wire which is coloured Yellow and Green must be connected to the

terminal which is marked E or or coloured Green.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE

MAINS SUPPLY.

WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT

ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY & OPERATION

Unpack the heater and check for any damage sustained in transit. Notify your

Clarke dealer immediately of any defects.

The heater is resistant to splashing but should be sheltered from direct rainfall,

as should the power cable, plug and supply outlet socket. A awning,

overhanging roof or other shelter should be used to protect from rain.

The heater should be positioned with at least 1 m clearance from any

combustible surfaces including furniture or other fabrics which could be

damaged by heat.

Ensure the heater faces the centre of

the space to be heated.

Never place any objects on, or

against the heater.

1. Set the lower tube (1) through the

hole in the base (2) with the

welded disc downwards & the

locating tongue in its seat in the

base. Secure with the washer (3)

and hand screw (4).

2. Connect tube (5) to the lower

tube (1) and secure with the two

screws.

3. Remove the screw (10) from the

end of the small tube (8) and

remove the locking ring (7) from

tube (6).

4. Slide the small tube (8) up through

the tube (6) (end with drilled hole

first), until it emerges from the

other end.

5. Screw the locking ring (7) back on

to tube 6.

6. Connect tube (6) to tube (5) and

secure with the two screws.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

7. Fit the small tube (8) into the

socket in the control box (9) and

secure with the screw (10).

8. Clip the power cable (11) to the

clips (12).

9. Set the downwards angle of the

heater by loosening the mounting

bracket with a large x-head

screwdriver and adjusting the

angle before re-tightening.

10. Set the heater to the required height by loosening the locking ring (7) and

extending the top tube as required. Tighten the locking ring to secure.

Ensure all fittings are suitable secure before using the heater.

11. Connect the mains cable to a suitable power socket.

12. Pull the string repeatedly to cycle

through the following heat

settings;

•O= Off

•I= Low

•II = Medium

•III = High

CLEANING AND MAINTENANCE

PERIODICALLY

1. If there is any serious build up of dirt, wipe thoroughly with a damp cloth,

taking care that no moisture enters the heater.

2. Inspect the power cable for damage. Undue heat will cause the cable to

stiffen and crack in which case it should be replaced.

3. Ensure heating elements are free of dust (use compressed air to clean if

possible. (Always wear a dust mask if performing this task).

4. Refer to your Clarke dealer if the heater element needs replacing.

WARNING: BEFORE CARRYING OUT ANY MAINTENANCE, ENSURE THE

HEATER IS SWITCHED OFF, IS DISCONNECTED FROM THE MAINS SUPPLY,

AND HAS BEEN GIVEN ADEQUATE TIME TO COOL DOWN.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

FAULT FINDING

TECHNICAL SPECIFICATION

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing Waste

Electrical and Electronic Equipment (WEEE) at a recognised disposal facility.

SYMPTOM PROBLEM SOLUTION

Heater does

not

operate,

although

plugged in

and

switched on.

Plug is loose/ bad con-

nection.

Remove the plug & check the con-

nection of the plug and socket.

Fuse blown. Replace if necessary and investi-

gate the cause. If fuse blow

repeatedly, consult your Clarke

dealer.

No power at socket outlet. Insert plug into a suitable socket.

Input voltage incorrect. Ensure power supply matches the

rating on the label.

Dimensions (L x W x H) 175 x 480 x 270 (lamp unit) mm

Assembled height on stand 1575 (min) to 1900 (max) mm

Weight (including stand) 10.75 kg

Electrical Supply 230 V / 50hz

Power Cable length 1.8 m

Protection Degree IP24 (water splash)

Operating Temperature -20 to 30°C

Tilt Range Level to -25 degrees

Heat Output 2 kW

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS DIAGRAM

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS LIST

ID DESCRIPTION ID DESCRIPTION

1 Front Housing 27 Cable Clamp

2 Front Housing Clip 28 Screw

3 Heating Element 29 Switch

4 Self-tapping Screw 30 Self tapping Screw

5 Reflector Bracket 31 Self tapping Screw

6Reflector 32Screw

7 Nut 33 Switch Bracket

8 Cable Clip 34 Cable Clip

9 Self tapping Screw 35 Screw

10 Spring Washer 36 Straight Tube

11 Rear Housing 37 Inner Fastener

12 Hinge Board 38 Upper Tube

13 U-seal Ring 39 Screw Plate

14 Hinge Seal 40 Middle Tube

15 Hinge 41 Lower Tube

16 Screw 42 Main Base

17 Control Box Bottom 43 Large Washer

18 Closed End Connector 44 Hand Screw

19 Seal 45 Internal Wiring Assembly

20 Control Box Cover 46 Power Cable

21 Nut 47 Screw

22 Internal Wire Assembly 48 Spring Washer

23 PVC Sticker 49 Star Washer

24 Cable Bush 50 Outer Sleeve

25 Drawing Bush 51 Base Cover

26 Display Disc 52 Joint

Inhaltsverzeichnis

Andere Clarke Heizung Handbücher

Clarke

Clarke DEVIL 4003 Bedienungsanleitung

Clarke

Clarke DEVIL 2800PTC-B Bedienungsanleitung

Clarke

Clarke 6933990 Bedienungsanleitung

Clarke

Clarke DEVIL 6025 Bedienungsanleitung

Clarke

Clarke OFR 5/50 Bedienungsanleitung

Clarke

Clarke DEVIL 370SPD Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 5000PTC Bedienungsanleitung

Clarke

Clarke DEVIL 350C Installations- und Betriebshandbuch

Clarke

Clarke XR60 Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 9000PTC Bedienungsanleitung

Clarke

Clarke Devil 370P Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 2000PTC Bedienungsanleitung

Clarke

Clarke DEVIL 7005 Bedienungsanleitung

Clarke

Clarke Devil 6003 Handbuch

Clarke

Clarke BR13/250 Bedienungsanleitung

Clarke

Clarke XR55 Installations- und Betriebshandbuch

Clarke

Clarke DEVIL 2800PTC Bedienungsanleitung

Clarke

Clarke Devil IRD20B Bedienungsanleitung

Clarke

Clarke CONTRACTOR DEVIL 351C Installations- und Betriebshandbuch

Clarke

Clarke Devil 355MD Betriebsanleitung

Clarke

Clarke DEVIL 350B 230V Installations- und Betriebshandbuch

Clarke

Clarke IRD40 6920415 Installations- und Betriebshandbuch

Clarke

Clarke XR60DV Bedienungsanleitung

Clarke

Clarke DEVIL IRD40B Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung

SUNWIND

SUNWIND ZSG101 Bedienungsanleitung