Clarke Woodworker CBS250C Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

DL1020 - ISS 1

ORIGINAL INSTRUCTIONS

250MM BANDSAW WITH STAND

MODEL NO: CBS250C

PART NO: 6460141

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE 250mm Bandsaw with stand.

Before attempting to operate the machine, it is essential that you read this

manual thoroughly and carefully follow all instructions given.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not affect your statutory rights.

ENVIRONMENTAL PROTECTION

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste but according to the laws governing Waste Electrical and

Electronic Equipment (WEEE) at a recognised disposal facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

1. Keep work area clear

• Cluttered areas and benches invite injuries.

2. Consider work area environment

•DO NOT expose tools to rain.

•DO NOT use tools in damp or wet locations.

• Keep work area well lit.

•DO NOT use tools in the presence of flammable liquids or gases.

3. Guard against electric shock

•AV O I D body contact with earthed or grounded surfaces (e.g. pipes,

radiators, ranges, refrigerators).

4. Keep other persons away.

•DO NOT let persons, especially children, not involved in the work touch

the tool or the extension lead and keep them away from the work area.

5. Store idle tools

• When not in use, tools should be stored in a dry locked-up place, out of

reach of children.

6. DO NOT force the tool

• It will do the job better and safer at the rate for which it was intended.

7. Use the right tool

•DO NOT force small tools to do the job of a heavy duty tool.

•DO NOT use tools for purposes not intended.

• Dress properly, DO NOT wear loose clothing or jewellery, they can be

caught in moving parts.

• Non-skid footwear is recommended when working outdoors.

• Wear protective hair covering to contain long hair.

8. Use personnel protective equipment

WARNING: WHEN USING ELECTRIC TOOLS BASIC SAFETY PRECAUTIONS

SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK AND PERSONAL INJURY INCLUDING THE FOLLOWING. READ ALL

THESE INSTRUCTIONS BEFORE ATTEMPTING TO OPERATE THIS PRODUCT

AND SAVE THESE INSTRUCTIONS

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Use safety glasses.

• Use ear protection

•Usegloves

• Use face or dust mask if working operations create dust

9. Connect dust extraction equipment

• The tool is provided with a connection for dust extraction and collecting

equipment, ensure these are connected and properly used.

10. DO NOT abuse the power cable

•NEVER yank the power cable to disconnect it from the socket. Keep the

power cable away from heat, oil and sharp edges.

11. Secure work

• Where possible use clamps or a vice to hold the work. It is safer than

using your hand.

12. DO NOT overreach

• Keep proper footing and balance at all times.

13. Maintain tools with care

• Keep cutting tools sharp and clean for better and safer performance.

• Follow instruction for lubricating and changing accessories.

• Inspect the tool power cable periodically and if damaged have it

repaired by a CLARKE service facility.

• Inspect extension cabling periodically and replace if damaged.

• Keep handles dry, clean and free from oil and grease.

14. Disconnect tools

• When not in use, before servicing and when changing accessories such

as blades, bits and cutters, disconnect tools from the power supply.

15. Remove adjusting keys and wrenches

• Form the habit of checking to see that keys and adjusting wrenches are

removed from the tool before turning it on.

16. AV O I D unintentional starting

• Ensure switch is in the “off” position when plugging in.

17. Stay alert

• Watch what you are doing, use common sense and DO NOT operate

the tool when you are tired or under the influence of drugs or alcohol.

18. Check damaged parts

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• Before further use of the tool, it should be carefully checked to

determine that it will operate properly and perform its intended

function.

• Check for alignment of moving parts, binding of moving parts,

breakage of parts, mounting and any other conditions that may affect

its operation.

• A guard or other part that is damaged should be properly repaired or

replaced by a CLARKE service centre.

• Have defective switches replaced by a CLARKE service centre.

•DO NOT use the tool if the switch does not turn it on and off.

19. WARNING

• The use of any accessory or attachment other than one recommended

in this instruction manual may present a risk of personal injury.

20. Have your tool repaired by a CLARKE service centre.

• This electric tool complies with the relevant safety rules. Repairs should

only be carried out by qualified persons using original spare parts,

otherwise this may result in considerable danger to the user.

ADDITIONAL

1. Position the fence on the lower side of the table when bevel-cutting with

the table inclined;

2. Use a suitable holding device when cutting round or irregular shaped

timber to prevent twisting of the work piece;

3. DO NOT use saw blades which are damaged or deformed;

4. DO NOT override the lockout and operate the tool, when the guards

protecting the saw blade is open;

5. DO NOT clean the saw blade whilst it is moving;

6. ALWAYS wear gloves for handling the saw blade and rough material.

7. The push-stick should be used if the distance between the blade and rip

fence is less than approx 150 mm.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity

supply is the same as that indicated on the rating plate. This product is

designed to operate on 230VAC 50Hz. Connecting it to any other power

source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to

change the fuse in the plug, the fuse cover must be refitted. If the fuse cover

becomes lost or damaged, the plug must not be used until a suitable

replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due

to damage, it should be cut off and a replacement fitted, following the wiring

instructions shown below. The old plug must be disposed of safely, as insertion

into a mains socket could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond

with the markings on the terminals of your plug, proceed as follows.

•TheBlue wire must be connected to the terminal which is marked Nor

coloured Black.

•TheBrown wire must be connected to the terminal which is marked Lor

coloured Red.

•TheYellow and Green wire must be connected to the terminal which is

marked E or coloured Green.

WARNING! Read these electrical safety instructions thoroughly

before connecting the product to the mains supply.

WARNING! The wires in the power cable of this product are

coloured in accordance with the following code:

Blue = Neutral Brown = Live Yellow and Green = Earth

Plug must be BS1363/A approved.

Always fit a 5 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

We strongly recommend that this machine is connected to the mains supply via

a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs

yourself.

SAFETY SYMBOLS

Read the manual

and safety

instructions before

use

Eye protection

should be worn

Ear protection

should be worn

Dust mask should be

worn

WARNING, Motor

gets hot

Do not touch moving

blade

WARNING, Risk of

injury, use push stick

were possible

Keep children and

bystanders at a safe

distance

Disconnect from

power source

before

maintenance or

repair

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONTENTS - BANDSAW

Make sure that all parts are un-damaged and are present. If any parts are

missing or damaged please contact your CLARKE dealer immediately.

The following loose components are supplied with the bandsaw assembly.

ITEM DESCRIPTION ITEM DESCRIPTION

1 Bandsaw Assembly 5 Spanner

2 Table 6 Allen Keys (3mm & 4mm)

3 Push Stick 7 Table Insert

4 Parallel Rip Fence Assembly 8 3 x M6 x 16 Bolt, Washer & Nut

1 x M6 x 35 Bolt & Nut

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONTENTS - STAND

Make sure that all parts are un-damaged and are present. If any parts are

missing or damaged please contact your CLARKE dealer immediately.

The following loose components are supplied with the stand assembly.

ITEM DESCRIPTION ITEM DESCRIPTION

1 2 x Long Beam - 400mm 6 2 x Assisted Support Leg -

190mm x 260mm

2 4 x Stand Legs - 560mm 7 24 x M8 x 16 Bolt, Washer & Nut

4 x M6 x 16 Bolt, Washer & Nut

4 x M8 x 45 Bolt, Washer & Nut

3 2 x Short Beam - 230mm 8 Allen Key (5mm)

4 4 x Rubber Feet 9 2 x Short Support Plate - 400mm

5 2 x Long Support Plate - 570mm

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

ASSEMBLE THE STAND

NOTE: All numbers in brackets correspond to the Contents - Stand list on

page 9.

1. Place the rubber feet (4) onto the

ends of the stand legs (2).

2. Attach the 4 stand legs (2) to the

outside of the 2 long beams (1) &

2 short beams (3), securing each

leg with 4 x M8 x 16 bolts, flat

washers and nuts. Hand tighten

nuts only at this stage.

3. Attach the 2 long support plates

(5) and 2 short support plates (9)

to the legs, secure each with 2 x

M8 x 16 bolts, flat washers and

nuts. Hand tighten nuts only at this

stage.

4. Attach the 2 assisted support legs

(6) to the 2 stand legs (2) on the

long support plate (5) side of the

stand, secure each with 2 x M6 x

16 bolts, flat washers and

nuts.Hand tighten nuts only at this

stage.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Gesehen Handbücher

Clarke

Clarke Woodworker MBS600C Bedienungsanleitung

Clarke

Clarke CCO14 Installations- und Betriebshandbuch

Clarke

Clarke contractor CON100 Installations- und Betriebshandbuch

Clarke

Clarke CRS710V Bedienungsanleitung

Clarke

Clarke Woodworker CBS12WC Installations- und Betriebshandbuch

Clarke

Clarke Contractor CFIS 250 Installations- und Betriebshandbuch

Clarke

Clarke Contractor CCS2 Installations- und Betriebshandbuch

Clarke

Clarke MBS600D Bedienungsanleitung

Clarke

Clarke CMS250S Bedienungsanleitung

Clarke

Clarke WOODWORKER CBS205 Bedienungsanleitung

Clarke

Clarke CBS-12WB Bedienungsanleitung

Clarke

Clarke X-PRO CAT167 Installations- und Betriebshandbuch

Clarke

Clarke STRONG ARM CFPSM Bedienungsanleitung

Clarke

Clarke CMS216S Bedienungsanleitung

Clarke

Clarke METALWORKER CBS 7MC Handbuch

Clarke

Clarke WoodWorker CCS1 Installations- und Betriebshandbuch

Clarke

Clarke CCO14B Bedienungsanleitung

Clarke

Clarke CSS400C Bedienungsanleitung

Clarke

Clarke CLS400 Kurzanleitung

Clarke

Clarke CMS255S Bedienungsanleitung

Clarke

Clarke CONTRACTOR CON185B Bedienungsanleitung

Clarke

Clarke CSS 400 Betriebsanleitung

Clarke

Clarke CCS185 Bedienungsanleitung

Clarke

Clarke Woodworker CMS10S2B Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung

Altrad

Altrad BELLE RANGER 450 Bedienungsanleitung

Porter-Cable

Porter-Cable 725 Bedienungsanleitung