Clarke X-pro CAT164 Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0517 -Issue 1

NEEDLE SCALER/CHISEL KIT

MODEL NO: CAT164

PART NO: 3120178

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Needle Scaler.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

4. Do not operate the tool where there are flammable liquids or gases.

5. Stay alert and use common sense - do not operate this tool when you are

tired or under the influence of alcohol, drugs or medication.

6. Always wear eye protection, ear defenders and gloves when using air

tools. Safety glasses must provide protection from flying particles from the

front and the side.

7. Do not overreach - keep proper footing and balance at all times.

USE

1. Never use oxygen, carbon dioxide, combustible gasses, or any bottled gas,

as a source of power for an air tool. This product should only be used with a

suitably rated compressed air supply.

2. Do not connect the air hose with your finger on the trigger.

3. Do not fit the air tool to any stand or clamping device that may damage it.

4. Do not exceed the maximum pressure for the tool of 6.2 bar.

5. Keep the air hose away from heat, oil and sharp edges.

6. Check hoses for leaks or excessive wear before use, and ensure that all

connections are secure.

7. Do not use the tool for any other purpose than described in this manual.

8. Do not carry out any alterations or modifications to the tool.

9. Always disconnect from the air supply when:

• Performing any maintenance.

• The tool is not in use.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• The tool will be left unattended.

10. Never use the tool if it is defective or operating abnormally.

11. This air tool should be serviced at regular intervals by qualified service

personnel.

12. Avoid damaging the air tool by applying excessive force of any kind.

13. Always maintain the air tool with care. Keep it clean for the best and safest

performance.

14. Do not force or misuse the air tool. It will do a better and safer job at the

rate for which it was designed.

15. Quick change couplings should not be located at the tool. They add

weight and could fail due to vibration.

16. Do not remove any labels. Damaged labels should be replaced.

17. This tool vibrates with use. Vibration may be harmful to your hands or arms.

Stop using the tool if discomfort, a tingling feeling or pain occurs. Seek

medical advice before resuming use.

AIR HAMMER SPECIFIC HAZARDS

1. Only use accessories designed for use with this power tool.

2. Never use any of the chisels supplied as hand struck tool.

3. Never use blunt chisels which require excessive pressure and can break

from fatigue.

4. Never abuse the tool by prising which can result in a broken tool.

5. Ensure there are no hidden electrical cables, gas pipes etc, which could

cause a hazard if damaged by action of the chisels.

TRANSPORTATION

1. Never carry the tool by the air hose or with your finger on the trigger.

2. Always disconnect from the air supply when changing bits or when the tool

is not required for immediate use in order to avoid accidental starting.

3. Wherever possible use both hands to control the tool.

4. Always ensure the tool has stopped before putting it down after use

5. When not in use the tool should be disconnected from the air supply and

stored in a dry place out of the reach of children.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 Needles 5 Trigger

2 Needle Holder 6 Female Air Inlet Connector

3 Chisel Retaining Spring 7 Speed Control Regulator

4Chisels

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition, but should

be regularly checked & topped up with oil. Clarke air-line oil should

be used, and the lubricator adjusted to approx 2 drops per minute.

• Never exceed the maximum operating pressure for the tool. It is

recommended that air pressure to this tool does not exceed 7 bar at

the tool when running. Higher pressures and unclean air will shorten

the life of the tool due to faster wear and is a possible safety hazard.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

FITTING THE NEEDLE HOLDER

The Needle Scaler is packed in two

halves:

• The main body/drive assembly

• The needle holder with needles

1. Screw the needle holder with

needles, firmly onto the nose of the

tool.

• Tighten the three grub screws

shown with a hex key to secure

the needle tube in place.

FITTING THE CHISELS

1. Insert the chisel into the air

hammer as shown.

2. Screw the retaining spring fully

onto the main body.

• Use the lugs to gain purchase

and tighten.

CONNECTING THE AIR SUPPLY

1. Remove the protective plug from the air inlet port and connect a suitable

hose.

2. A gauze filter is fitted within the air inlet adapter. Ensure this filter is always in

place and clean. The airline is connected to the adapter, preferably via a

quick release coupling (not supplied).

3. Connect the other end of the hose to the compressor.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

4. Turn on the air supply and check for air leaks. Rectify any found before

proceeding.

• PTFE tape may be useful for sealing threaded connections.

5. If required, connect an in-line mini oiler to the tool.

• A mini oiler helps to prolong the life of the air tool.

6. If a mini-oiler is not being used, run a few drops of oil through the tool

before use. It can be entered through the airline connector or via the hose

at the nearest connection to the air supply.

7. Ensure the trigger is NOT depressed when connecting the air line.

ACCESSORIES AND CONSUMABLES

A wide range of airline accessories is available including filter/regulators,

lubricators, high-pressure hoses (5 to 50 metres) etc. Contact your Clarke

dealer or Clarke International Service Department for further information.

Clarke Air-lne Oil (Part no. 3050825) is available from your Clarke dealer.

Replacement needle set;- CAT172 (Clarke part no; 3120189).

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

USING THE TOOL

1. Hold the tool firmly, then bring the

tool towards the work at an angle

of approximately 60-70 degrees.

2. Pull the trigger with the chisel in

light contact with the work.

3. Move slowly across the work

surface. To remove scale, rust or

other contaminants, only a light

force should be required.

4. Release the trigger to stop

operation, whilst maintaining contact with the work. Note that the tool may

run briefly after the trigger is released.

5. Needle or chisel force can be

adjusted by turning the regulator

knob located at the base of the

hand grip.

6. To increase speed, turn the

regulator clockwise or anti-

clockwise to reduce.

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the compressed air supply hose until the air supply has

been shut down or isolated at the shut off valve and the compressed air

expelled by running the tool until it stops.

2. Refer to the compressor instruction manual for the procedure to shut down

and release the compressed air.

3. Once the pressure has been released, disconnect the air supply hose from

the needle scaler.

WARNING: ALWAYS WEAR PPE TO PROTECT YOURSELF FROM FLYING

PARTICLES WHEN USING THIS PRODUCT.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

Please note that factors other than the tool may effect its operation and

efficiency such as reduced compressor output, excessive drain on the airline,

moisture or restrictions in the air-line, or the use of connectors of improper size

or poor condition which will reduce air supply.

DAILY

1. Before use, drain water from the air-line and compressor.

2. Lubricate the air tool daily for optimum performance, using a high quality

airline oil either via a lubricator in the air supply system or by placing a few

drops into the air inlet immediately before use. This should be carried out

regardless of whether or not an in-line lubricator is used.

CLEANING & OVERHAUL

1. Keep the tool clean and free from debris.

2. Grit or gum deposits in the mechanism may eventually reduce efficiency.

This condition can be corrected by cleaning the air inlet strainer and

flushing out the tool with gum solvent oil or an equal mixture of SAE No10 oil

and paraffin.

3. Failing this, the tool should be disassembled, thoroughly cleaned, dried

and reassembled. You may prefer to take the tool to your CLARKE dealer if

internal maintenance is required.

4. If the tool becomes sluggish and the air supply is of good quality, it may be

necessary to replace worn or damaged parts. You may prefer to take the

tool to your Clarke dealer if internal maintenance is required.

5. Replacement needles can be fitted if required as described on page 7.

STORAGE

If the tool is to be stored, or is idle for longer than 24 hours, run a few drops of

Clarke air-line oil into the air inlet and depress the trigger in order to lubricate

the internal parts.

When not in use, the tool should be disconnected from the air supply and

stored in a dry place out of the reach of children. Avoid storing in a damp

environment or where the temperature is below 0oC.

WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE

PROCEDURES.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Werkzeuge Handbücher

Clarke

Clarke CMC36B Bedienungsanleitung

Clarke

Clarke GWH8 Bedienungsanleitung

Clarke

Clarke Air CHR9P Bedienungsanleitung

Clarke

Clarke KIT700 Bedienungsanleitung

Clarke

Clarke CHT637 Installations- und Betriebshandbuch

Clarke

Clarke CAT125 Installations- und Betriebshandbuch

Clarke

Clarke CAT66 Bedienungsanleitung

Clarke

Clarke CAT216 Installations- und Betriebshandbuch

Clarke

Clarke CONTRACTOR CHJ110 Bedienungsanleitung

Clarke

Clarke CAR8P Bedienungsanleitung

Clarke

Clarke CAT138 Installations- und Betriebshandbuch

Clarke

Clarke SBR760 Bedienungsanleitung

Clarke

Clarke X-PRO CAT208 Installations- und Betriebshandbuch

Clarke

Clarke CAT33B Installations- und Betriebshandbuch

Clarke

Clarke CEA150 Installations- und Betriebshandbuch

Clarke

Clarke CFC100 Installations- und Betriebshandbuch

Clarke

Clarke CAT218 Installations- und Betriebshandbuch

Clarke

Clarke CHT 454 Bedienungsanleitung

Clarke

Clarke CHT172 Bedienungsanleitung

Clarke

Clarke Strong-Arm CFB600 Bedienungsanleitung

Clarke

Clarke Air CAT62 Installations- und Betriebshandbuch

Clarke

Clarke CONTRACTOR CLJ120 Bedienungsanleitung

Clarke

Clarke CONTRACTOR CSJ100 Bedienungsanleitung

Clarke

Clarke Strong-Arm CLL500 Handbuch

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung