Clarke CFTP12 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1120 - iSS 2

12V OIL & DIESEL PUMP

MODEL NO: CFTP12

PART NO: 7160100

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Pump. The CFTP12 pump is designed

only for use with diesel fuels and automotive oil and is suitable for extracting

automotive oil from vehicle engines via the dip stick/filler hole.

It must not be used with water, petroleum fuels or alcohol, nor if small solids are

known to be in suspension.

Contents: 1 x Pump, 1 x Inlet Hose, 1 x outlet Hose, 2 x Hose Clips.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase. This guarantee is invalid if the product is found to have been

abused or tampered with in any way, or not used for the purpose for which it

was intended.

Faulty goods should be returned to their place of purchase. No product can

be returned to us without prior permission. This guarantee does not effect your

statutory rights.

IMPORTANT

Please read all of the safety and operating instructions carefully before using

this product. The following safety symbols may be found on the product.

Keep these instructions in a safe place for future reference.

Read this instruction

booklet carefully

before use.

Wear protective gloves

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

SAFETY PRECAUTIONS

WORK AREA

1. Keep the work area clean and well lit. Cluttered and dark areas invite

accidents.

2. Do not operate power products in explosive atmospheres such as in the

presence of flammable liquids, gasses or dust. Power products create

sparks which may ignite dust or fumes.

ELECTRICAL SAFETY

1. Do not abuse the electrical cable. Keep the cable away from sources of

heat, oil, sharp edges or moving parts. Damaged or tangled cables

increase the risk of electric shock.

PUMP SAFETY

1. DO NOT use this pump where there is a danger of fire.

2. DO NOT use to pump ANY liquid other than diesel and automotive oil.

3. ALWAYS ensure the ON/OFF switch, mounted on the rear of the pump, is in

the OFF (O) position, BEFORE connecting to the battery This is to avoid the

possibility of arcing taking place, thereby reducing the risk of fire.

4. Switch the pump OFF immediately after the task is completed.

5. Do not use the pump if the switch does not turn it on and off. Any power

product that cannot be controlled with the switch is dangerous and must

be repaired.

6. If necessary, have your pump repaired by a qualified person using

identical replacement parts. This will ensure that the safety of the product is

maintained.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ENVIRONMENTAL PROTECTION

1. Take care to ensure that if diesel fuel is spilt that it is cleaned away using

sand or treated with absorbent granules designed for the purpose.

2. Always make every effort to contain any spillage and prevent ingress into

the local water course.

ELECTRICAL CONNECTION & OPERATION

1. Connect the inlet and outlet hoses

to the pump after removing the

black plastic caps as shown.

NOTE: The black plastic flange

remains fixed to the pump

connection.

2. Connect the inlet and outlet hoses

to the pump using the hose clips

supplied.

• The hose and connections need

to be completely air tight,

otherwise air will be drawn in

and reduce the flow.

• The smaller hose (marked IN) is

designed to fit the dipstick

opening and the larger one is

the outlet hose.

3. Insert the inlet/outlet tubes into the engine dipstick opening and a suitable

container for waste oil.

4. Ensure the ON/OFF switch, located

at the rear of the pump, is set to

the OFF (O) position BEFORE

connecting the pump to the car

battery.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

Position the pump on a suitable surface in the engine bay as shown.

Only connect this pump to a 12V battery.

Ensure also that the battery terminals are clean and firmly attach the RED

clamp to the POSITIVE and the BLACK clamp to the NEGATIVE terminals

respectively.

Double check to ensure the clamps cannot be disturbed easily, and that the

WARNING: THIS IS TO AVOID THE POSSIBILITY OF SPARKING TAKING

PLACE AND THEREBY REDUCING THE RISK OF FIRE. DO NOT USE WITH

PETROL OR ANY OTHER HIGHLY FLAMMABLE LIQUID.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

setup is protected from passers by. Set the switch, at the rear of the pump to

ON (I).

Do not allow the pump to run dry for more than 30 seconds after pumping has

stopped.

MAINTENANCE

The pump requires no maintenance, but should be inspected before use to

ensure that the electric power cables and clamps are in good condition.

Ensure that the hoses used are perfectly sound.

Avoid using solvents if cleaning plastic parts, as most plastics are susceptible to

damage from various types of commercial solvents.

Store the pump in dry conditions protected from the weather.

For any problems requiring dismantling of the pump, contact your CLARKE

dealer.

SPECIFICATIONS

Please note that the details and specifications contained herein, are correct at the time

of going to print. However, CLARKE International reserve the right to change

specifications at any time without prior notice. Always consult the pump’s data plate.

Fluid Classification / Fluids to be used Clean (motor oil, diesel)

Max. Head 0.7 m

Max. Flowrate (dependant upon

temperature/type of oil)

1.5 litres/min (diesel)

0.2 litres/min (engine oil)

Max Operating Time 30 mins

Max. Temperature of liquid being pumped 60oC (Oil) / 45oC (Diesel)

Self Priming Yes

Weight 0.85 kg

Inlet Hose Length 1.2 m

Outlet Hose Length 1.6 m

Motor 12V DC / 9.4 A

IP Rating IPx4

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DECLARATION OF CONFORMITY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Wasserpumpe Handbücher

Clarke

Clarke TAM101 Installations- und Betriebshandbuch

Clarke

Clarke PW2 Bedienungsanleitung

Clarke

Clarke CSV4A Bedienungsanleitung

Clarke

Clarke CEB103 Bedienungsanleitung

Clarke

Clarke ISP14A Installations- und Betriebshandbuch

Clarke

Clarke PW50 Bedienungsanleitung

Clarke

Clarke HSE Series Installations- und Betriebshandbuch

Clarke

Clarke DWP300A Bedienungsanleitung

Clarke

Clarke CU150 Installations- und Betriebshandbuch

Clarke

Clarke PSV3A Bedienungsanleitung

Clarke

Clarke CPPRSS Bedienungsanleitung

Clarke

Clarke DW75 Bedienungsanleitung

Clarke

Clarke BIP1500 Bedienungsanleitung

Clarke

Clarke DW50 Bedienungsanleitung

Clarke

Clarke PF75A Bedienungsanleitung

Clarke

Clarke PF75 Bedienungsanleitung

Clarke

Clarke DFT12 Bedienungsanleitung

Clarke

Clarke CWP200 Bedienungsanleitung

Clarke

Clarke CDDFTP Bedienungsanleitung

Clarke

Clarke CSV1A Bedienungsanleitung

Clarke

Clarke CBP900 Bedienungsanleitung

Clarke

Clarke CPE30A3 Bedienungsanleitung

Clarke

Clarke CSE2 Bedienungsanleitung

Clarke

Clarke CPE30A1 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung