Clarke MSP12 Bedienungsanleitung
SUBMERSIBLE TRANSFER PUMP
Model No: MSP12
Part No: 7260040
Thank you for purchasing this Clarke Mini Submersible Pump.
Please read this leaflet thoroughly before use to ensure you are fully aware of the limitations
and methods of use and of all safety precautions that must be taken into consideration.
This will also ensure that with proper use, the pump will provide you with many years of
satisfactory service.
Guarantee
This CLARKE product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered
with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be
returned to us without prior permission.
This guarantee does not effect your statutory rights.
Please check the contents to ensure they are complete and that no transit damage has
occurred.
Should any damage be apparent, please contact your Clarke dealer immediately
When disposing of this product, do not dispose of with general waste. It must be disposed of according to the laws
governing Waste Electrical and Electronic equipment, at a recognised disposal facility.
Contents
• 1 pump c/w 4m supply cable with crocodile clips
• 3m flexible hose
• 2 x 15mm jubilee clips
• 15mm steel tube x 150mm length
Safety Precautions
This pump is ONLY for use with the following:
• Clean water or water with small solids in suspension (dirty water).
• Diesel fuel
• Paraffin
DO NOT use this pump for pumping:
• Slurry
• Sceptic Tanks
• Sandy water
• WARNING: DO NOT USE FOR PUMPING PETROL
•ALWAYS disconnect the pump from the power supply before performing any
maintenance operations.
•ALWAYS check the power input cable before use to ensure it is perfectly serviceable.
•ALWAYS ensure the filter is clean and perfectly serviceable before use.
•NEVER run the pump dry. Minimum water depth is 30mm
•DO NOT exceed the duty cycle - see Specifications.
•DO NOT use if any part appears to be damaged. Have it repaired by your Clarke dealer.
•DO NOT use the pump for any purpose other than that for which it is intended.
•DO NOT operate the pump continuously - eg. in a fish pond or collection tank, water
feature etc.
•DO NOT use or leave the pump in freezing conditions.
•DO NOT allow uncontrolled discharge of
contaminated
water etc. ALWAYS collect in
a container and dispose of according to all H & S regulations and local laws.
Specifications
Flow Rate ..................................................... 16.5 litres/min
Min. Water Depth ...................................... 30mm
Voltage ........................................................ 12V
Current ......................................................... 4.5A DC
Pressure ........................................................ 15psi / 1 bar
Height .......................................................... 145mm
Diameter ...................................................... 53.5mm
Weight .......................................................... 0.6kg
Duty cycle ................................................... 15mins continuous in any
30 min period
Limitations of Use
Method of Operation
1. Always check to ensure the pump is in perfect working order:
- has no apparent damage
- the filter is in place and perfectly clean
- the power cable is in perfect condition
2. Attach the flexible hose to the outlet, securing with the jubilee clip supplied.
3. If required, attach the stainless steel tube to the discharge end of the flexible hose,
securing with the jubilee clip supplied.
4. Carefully lower the pump into the pit or sump etc., to be drained.
IMPORTANT, if the bottom of the pit or sump is muddy or sandy, support the pump on a
brick or something similar. DO NOT allow it to rest in the mud or sand.
5. Connect the clamps to the 12Volt battery and the pump will operate.
IMPORTANT: ALWAYS connect the red - positive clamp to the red positive terminal of the
battery FIRST, then connect the black clamp to the black - negative terminal, ensuring both
clamps are perfectly secure.
When disconnecting - ALWAYS disconnect the black - negative clamp FIRST.
Always observe the pump discharge. Should it deteriorate during use, it is probable that the
filter is becoming blocked. In this case, disconnect the pump from the battery - black terminal
first, then carefully withdraw the pump from the pit or sump etc. DO NOT yank the cable.
Unscrew the base cap and remove the filter. Either clean thoroughly or replace as necessary,
then check the impeller to ensure it is free to rotate and is not blocked.
When satisfied, replace pump in sump or pit etc., and proceed to pump once more.
When finished, ALWAYS remove the filter and clean it thoroughly, then allow it to dry.
Thoroughly clean the pump with clean water and ensure the impeller is completely free
to rotate and is free of any contaminants.
Reassemble the pump and store in a clean, dry environment.
Parts and Service
The following parts are available from your Clarke dealer:
1. End Cap Part No: MSP1201
2. Filter MSP1202
3. Cable Clamp - Red MSP1203
4. Cable Clamp - Black MSP1204
5. Flexible Hose - 4M MSP1205
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE TEL: 020 8988 7400
PARTS & SERVICE FAX: 020 8558 3622
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Clarke Wasserpumpe Handbücher
Clarke
Clarke HSEC651A Bedienungsanleitung
Clarke
Clarke CPE Series Bedienungsanleitung
Clarke
Clarke CFTP12 Bedienungsanleitung
Clarke
Clarke DW75 Bedienungsanleitung
Clarke
Clarke CSD4 Bedienungsanleitung
Clarke
Clarke SUBMERSIBLE PUMP Bedienungsanleitung
Clarke
Clarke CSV1A Bedienungsanleitung
Clarke
Clarke STP12 Bedienungsanleitung
Clarke
Clarke ECP20A3 Bedienungsanleitung
Clarke
Clarke HSE Series Installations- und Betriebshandbuch
Clarke
Clarke IVP14A Bedienungsanleitung
Clarke
Clarke DWP400A Bedienungsanleitung
Clarke
Clarke DWP300A Bedienungsanleitung
Clarke
Clarke HSE RANGE Bedienungsanleitung
Clarke
Clarke CS85S Installations- und Betriebshandbuch
Clarke
Clarke DFT12 Bedienungsanleitung
Clarke
Clarke CD1 - 1 Installations- und Betriebshandbuch
Clarke
Clarke CPRP560 Bedienungsanleitung
Clarke
Clarke SPE800 Installations- und Betriebshandbuch
Clarke
Clarke FP150 Bedienungsanleitung
Beliebte Wasserpumpe Handbücher anderer Marken
Sykes AmeriPumps
Sykes AmeriPumps GP100M Fehlerbehebungshandbuch
DUROMAX
DUROMAX XP WX Series Bedienungsanleitung
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Bedienungsanleitung
Franklin Electric
Franklin Electric IPS Bedienungsanleitung
Xylem
Xylem e-1532 Series Bedienungsanleitung
Milton Roy
Milton Roy PRIMEROYAL Bedienungsanleitung