Clarke HIPPO 2 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0120 - rev 5

SUBMERSIBLE PUMP

MODEL NO: HIPPO 2/2A

PART NO: 7230023, 7230024 & 7230025

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Hippo submersible pump. Hippo 2 has

the same specification as the Hippo 2A but without a float switch.

The Hippo 2 can be supplied for either 110V (part No 7230023) or 230V (part

No 7230024) power supplies.

This pump is designed for pumping clean water.

It is NOT designed for pumping slurry, sludge, mud or heavily polluted water, or

any water containing chemicals or other acidic contaminants including salt

water.

SPECIFICATIONS

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Voltage 230V~50Hz or 110V

Outlet Thread Diameter 1“BSP

Power 250W

Maximum Head Height 6 m

Maximum Output Flow 85 l/min

Weight 3.65 kg

Cable Length 6 m

Dimensions (L x W x H) 158 x 143 x 265 mm

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY INSTRUCTIONS

GENERAL

1. Read all instructions before use

and save these instructions for

future use.

2. An approved residual current

device (RCD) which has a

tripping current of less then 30mA

MUST be used for all operations.

3. The electrical supply must be the

same as that on the rating plate.

4. Always make sure that your

hands are dry when connecting

or disconnecting from the mains

supply.

5. Never pull the mains lead to

disconnect the pump from the

mains socket.

6. The mains plug must be kept

away from the water at all times.

7. Do not allow children or

unauthorised people to touch the

pump, cables or connections.

8. Disconnect the pump from the

mains supply when not in use.

9. If necessary have the pump

repaired by a qualified person.

10. Keep the mains lead away from

heat, oil and sharp edges.

11. If you have to use an extension

lead with this product, it must be

designed for outdoor use and

incorporate a cable suitable for

use with Class I appliances.

12. Disconnect the pump from the

electrical supply and wear gloves

during servicing or maintenance.

PUMP SPECIFIC

1. Do not pump explosive /

flammable liquids or chemicals.

2. Never allow the pump to run dry

or operate out of the water.

3. Submersible pumps should always

be submerged and stored

vertically.

4. Disconnect the pump from the

mains supply before placing it

into or removing it from the water.

5. Always check the plug and all

cables for damage before use.

6. Do not use the pump if

damaged. Refer to qualified

service personnel for repair.

7. Never carry or lower the pump by

the power cable always use the

handle or a rope tied securely to

the handle.

8. Never insert your fingers into the

pump whilst it is connected to the

mains.

9. Never use the submersible pump

in a swimming pool when there

are people or animals in the pool.

10. Keep the pump clear of

sediment by standing it on a

platform or brick or suspending it

at a suitable depth.

11. Do not use the pump if the water

is liable to freeze as this can

cause damage to the pump.

Remove the pump from the

water and store it in a frost free

location.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS - 230V UNITS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely, as

insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings

on the plug.

• The BLUE wire must be

connected to the

terminal marked N.

• The BROWN wire must

be connected to the

terminal marked L.

• The YELLOW AND

GREEN wire must be

connected to the

terminal marked E or

AN APPROVED RESIDUAL CURRENT DEVICE (RCD) WHICH HAS A TRIPPING

CURRENT OF LESS THAN 30 mA MUST BE USED.

If you are not sure, consult a qualified electrician. DO NOT try to do any

repairs.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

Earth

(Green and

a 5 Amp

the cable is firmly held by the clamp

fuse.

Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS -110V UNITS

HIPPO 2 - 110 VOLT UNITS

This product can be connected to one of the following power supplies:

• 110V generator

• 110V isolating transformer

• 110V site supply

• 230V generator via a 110V transformer.

Connecting it to any other power source may cause damage.

This product includes a fitted industrial plug to BS-EN

60309, and a cable for use with a 110 volt supply. On

no account must a 230V, 13amp (BS1363) plug be

used.

If using a portable 110V transformer, make sure it has a

rated capacity sufficient to take the load of the

pump.

Should the plug need changing at any time, ensure

that a plug of identical specification is used and

proceed as follows:

1. Undo the socket screws & remove the rear section.

2. Rotate the cable clamp clear of the terminals.

3. Feed the cable through the rear gland in the plug.

4. Remove the cable sheath to the required lengths

as shown in the diagram.

5. Terminate the correct wires in the

correct terminal blocks as shown.

6. Remove the cable clamp screws. Clip

the cable clamp back into position and

place the clamp around the outer

sheath of the cable. Replace the screws

and tighten until the cable is securely

held.

7. Replace the rear cover and tighten the cover screws.

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs

yourself.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

Remove all packaging and make sure that the pump has no visible damage.

Dispose of all packaging appropriately.

FITTING THE HOSE ADAPTOR

A selection of adaptors in ½”, ¾” and 1”sizes are supplied. The hose adaptor

must be screwed onto the pump outlet.

1. Fit the required size adaptor according to the hose being used.

• Reducing the hose diameter will effect the maximum flow rate.

2. Connect a suitable hose (not supplied) to the adaptor

• Suitable hoses are available from your local Clarke dealer.

POSITIONING AND OPERATING

1. Place the pump on a flat surface in the area that you want to drain.

• If the pump is to be used where there may be silt or mud (for example,

garden ponds), keep the pump clear of sediment by standing it on a

platform or brick.

• In deep water it may be helpful to raise and lower the pump using a

rope attached to the lifting handle. Do not lift the pump by the mains or

float switch cables.

• Take all necessary precautions as described on page 3.

2. Connect the mains plug to the power supply. The pump will begin to drain

water.

• Always use a high sensitivity residual current device (RCD) which has a

tripping current of less then 30 mA.

• The Hippo 2 is designed for use with clean fresh water. Avoid using your

pump with salt water or with water containing chemicals as these can

cause damage to the pump. If the pump does come into contact with

salt water or chemicals, wash it in fresh water immediately.

WARNING: CHECK THE PUMP FOR DAMAGE BEFORE USE, DO NOT USE THE

PUMP IF DAMAGED IN ANY WAY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

3. Do not use the pump if the water is liable to freeze as this can damage the

pump. Remove the pump from the water and store it in a frost free

location.

4. Inspect the pump regularly to check that the base inlet is clear of leaves or

other debris. Any blockage of mud or leaves can be cleared by washing

the pump in fresh water, or by using a garden hose to flush fresh water

back through the pump outlet connector.

5. Never switch on the pump with the outlet connected to the mains water

supply. The mud pack (item 2) and screen/filter (item 6) can be removed

for cleaning if necessary. Remove the mud pack (3 screws around the

base), followed by the screen/filter (3 more screws) if necessary.

6. Keep watch and do not allow the pump to run dry.

• When fitted (Hippo 2A), the float switch will turn off the pump when the

water level drops to a low level.

7. When pumping is finished, disconnect the pump from the power supply.

MAINTENANCE

This pump should require no maintenance other

than regular cleaning. If the pump starts to show

signs of wear or damage contact the Clarke

service department for advice. Do not use the

pump if there is any damage to the mains supply

cable. Do not attempt to repair the pump yourself

(other than to replace those parts listed below), as

you may invalidate your guarantee and damage

the waterproof seal of the pump.

To fit a new power lead, remove the two screws

and the retaining plate from around the power

lead connector plug and pull the plug from its

socket.

When replacing, the plug must be sealed using a

clear silicon sealant. Apply the sealant to the body

of the connector plug as shown in the diagram,

before inserting it into its socket and replacing the retaining plate and screws.

WARNING: BEFORE CHECKING THE CONDITION OF THE PUMP, ENSURE IT

IS UNPLUGGED FROM THE MAINS SUPPLY. IF THE UNIT IS HARD WIRED,

ENSURE THE CIRCUIT BREAKER IS OPEN.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

If using this pump in a garden pond, please note that there is a small quantity

of oil in the pump seal. If the pump or seal is damaged, the oil may leak out,

and appear as a film on the surface of the water. Although harmless to

people, the oil must be cleared to prevent any possible harm to pond life.

Disconnect the pump from the electrical supply, remove it from the pond, and

clear the oil, then contact our Service Department for advice.

CLEANING

Check the pump installation regularly to ensure the water inlet is clear of

leaves or other debris. Take extra care to remove any debris from around the

impeller.

STORAGE

When the pump is not being used for extended periods, clean and dry it

thoroughly and store in indoors. if the pump is left in water, it must be run at

least once a week to prevent it from seizing up.

ENVIRONMENTAL RECYCLING POLICY

By purchasing this product, the customer is taking on the obligation to

deal with its safe and ethical disposal in accordance with the Waste

Electrical and Electronic Equipment (WEEE).

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognized disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TROUBLESHOOTING

PROBLEM SOLUTION

PUMP WILL

NOT START

1. Make sure that the power is switched on.

2. Check fuse (consult an electrician if in doubt).

3. If an extension lead is fitted, check connections (consult

an electrician if in doubt).

4. Internal thermal cut-out has not re-set. Leave for 5-10

minutes and try again.

5. The impeller may be jammed. Disconnect from the mains

supply and remove any objects that may be obstructing

the impeller.

6. Water level is below the minimum level required by the

float switch.

7. If the pump still fails to start, consult your CLARKE dealer

for advice.

PUMP WILL

START BUT NOT

PUMP

1. Check that the inlet is not blocked.

2. Check that the outlet is not clogged or obstructed.

3. The head may be too great, i.e. you are trying to lift the

water too great a distance for the pump to cope with.

4. Air bubble in the pump, produced during immersion.

immerse the pump again, at an angle, and shake it whilst

lowering to remove any air trapped in the system.

5. Impeller may be damaged - Consult your CLARKE dealer.

PUMP WILL

NOT STOP

1. Pump set to manual mode.

2. Float switch may be faulty. Consult your CLARKE dealer

for advice.

PUMP STOPS

RUNNING

1. Thermal overload has operated. Leave for 5-10 minutes

and try again.

2. Pump has run dry or float switch has cut in.

3. A foreign object has jammed the impeller.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS LIST & DIAGRAM

1 Base 72000940

2 Mud-pack 72000941

3 Cable with connector 72000942

4 Impeller (screw fit to shaft 72000943

5 Gasket 72000944

6 Screen/filter 72000945

7 1/2” adaptor 72000946

8 3/4” adaptor 72000947

9 1” adaptor 72000948

Andere Handbücher für HIPPO 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Wasserpumpe Handbücher

Clarke

Clarke SWP900A Bedienungsanleitung

Clarke

Clarke ISP14A Installations- und Betriebshandbuch

Clarke

Clarke HSE Series Installations- und Betriebshandbuch

Clarke

Clarke CPPRSS Bedienungsanleitung

Clarke

Clarke PSV5A Bedienungsanleitung

Clarke

Clarke Hippo 2A Handbuch

Clarke

Clarke CVPS Kurzanleitung

Clarke

Clarke PW80A Bedienungsanleitung

Clarke

Clarke BIP1000 Bedienungsanleitung

Clarke

Clarke DWP210A Bedienungsanleitung

Clarke

Clarke CS85S Installations- und Betriebshandbuch

Clarke

Clarke CM1 Installations- und Betriebshandbuch

Clarke

Clarke PW2 Bedienungsanleitung

Clarke

Clarke CSD4 Bedienungsanleitung

Clarke

Clarke ECP15A1 Bedienungsanleitung

Clarke

Clarke IVP13A Installations- und Betriebshandbuch

Clarke

Clarke SPE800 Bedienungsanleitung

Clarke

Clarke Hippo4A Bedienungsanleitung

Clarke

Clarke psp125b Bedienungsanleitung

Clarke

Clarke DFT12 Bedienungsanleitung

Clarke

Clarke STP12 Bedienungsanleitung

Clarke

Clarke CBB75 Bedienungsanleitung

Clarke

Clarke CFT230 Handbuch

Clarke

Clarke LVP1A Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung