Clarke PSV3A Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

GC0111

SUBMERSIBLE PUMPS

Model Nos:PSV3A, PSV4A, PSSV2A,

PVP11A & PSD1A

Part Nos; 7236042, 7236044, 7236050, 7236060 & 7236070

INTRODUCTION

Thank you for purchasing this CLARKE submersible pump.

Before attempting to use this product, please read this manual thoroughly

and follow the instructions carefully. In doing so you will ensure the safety of

yourself and that of others around you, and you can look forward to the

product giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not affect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste at the

end of its life. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment, at a recognised disposal

facility. Any old tools, accessories and packaging should be sorted

and disposed of in an environmentally appropriate manner.

SPARES & SERVICE CONTACTS

For parts & servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

TABLE OF CONTENTS

INTRODUCTION ..................................................................................2

GUARANTEE ........................................................................................2

ENVIRONMENTAL PROTECTION .........................................................2

SPARES & SERVICING CONTACTS ......................................................2

TABLE OF CONTENTS ..........................................................................3

GENERAL SAFETY PRECAUTIONS .......................................................4

ELECTRICAL CONNECTIONS .............................................................. 5

OVERVIEW ..........................................................................................7

OPERATION ......................................................................................... 8

CLEANING & MAINTENANCE.............................................................10

PUMP PERFORMANCE ........................................................................11

FAULT FINDING ....................................................................................12

TECHNICAL SPECIFICATIONS .............................................................13

PARTS LISTS & SPARES DIAGRAMS ......................................................14

DECLARATION OF CONFORMITY.......................................................22

GENERAL SAFETY PRECAUTIONS

As with all machinery, there are certain hazards involved with its

operation and use. Exercising caution will reduce the risk of

personal injury.

WORK AREA

1. Keep the work area clean and well lit. Floors should always be kept clear.

Cluttered or dark areas invite accidents.

2. Keep children and bystanders away while operating the pump.

Distractions can cause loss of control.

3. Remember, the operator or user is responsible for accidents or hazards

occurring to other people or their property.

PERSONAL SAFETY

1. ALWAYS stay alert, watch what you are doing and use common sense

when operating this pump. Do not install the pump while you are tired or

under the influence of medication, drugs or alcohol. A moment of

inattention can result in personal injury.

2. Do not over-reach. Keep your proper footing and balance at all times

when positioning the pump.

3. NEVER direct the water discharge towards electrical wiring or equipment.

4. ALWAYS store the pump out of reach of children and do not allow persons

unfamiliar with these instructions to operate it.

5. NEVER direct the discharge flow towards another person.

6. ALWAYS thoroughly familiarise yourself with this pump & its operation and

follow all instructions in this manual.

7. ALWAYS ensure that the pump is properly positioned where necessary to

prevent it from moving during operation, and that the immediate area

surrounding the pump is kept clear.

GENERAL USE AND CARE OF THE PUMP

1. An approved Residual Current Device (RCD) must be used when pumping

from ponds or swimming pools.

2. ALWAYS lift the pump using the handle and use a rope or chain attached if

necessary to lower it into the pit or excavation. Never lift or carry the

pump by the power cable or by the float switch cable.

3. NEVER use this pump if any part is damaged. Have it inspected and

repaired by your local Clarke dealer.

4. ALWAYS use an extension cable suitable for outdoor use when operating

outdoors. Using the correct cable reduces the risk of electric shock.

5. ALWAYS maintain the pump with care and keep it clean.

6. ALWAYS use an approved cable extension suitable for the power rating of

the pump (see specifications). The conductor size should also be at least

the same size as that on the pump, or larger. When using a cable reel,

always unwind the cable completely.

7. NEVER use for pumping flammable liquids or corrosive chemicals. These

pumps are designed to pump water only.

8. NEVER abuse the electrical cable. Never use the cable for pulling or

unplugging the pump Damaged or tangled cables increase the risk of

electric shock.

9. NEVER run the pump dry. Always ensure the pump is immersed in water

before starting. Switch the pump OFF immediately the task is completed

10. NEVER pump water from a swimming pool when there is a person or

animal still in the pool.

11. NEVER install the pump on sand, silt or mud which is likely to shift or

collapse.

12. NEVER modify this pump in any way. Use it only for the purpose for which it

is designed.

SERVICING & REPAIRS

1. ALWAYS have the pump serviced by your local CLARKE dealer, using only

identical replacement parts. This will ensure the safety of the pump is

maintained. The use of non standard parts could be hazardous.

2. NEVER attempt any repairs yourself. If you have a problem with the pump

contact your local CLARKE dealer.

3. ALWAYS disconnect the pump from the electrical supply before placing it

into, or removing from the water, and before any cleaning or

maintenance.

4. If the power cable becomes damaged, it must be replaced rather than

repaired.

Your CLARKE water pump has been designed to give long and trouble free

service. If, however, having followed the instructions in this booklet carefully,

you encounter problems, take the unit to your local CLARKE dealer.

Please keep these instructions in a safe place for future reference.

ELECTRICAL CONNECTIONS

WARNING! Read these electrical safety instructions thoroughly

before connecting the product to the mains supply.

Before switching the machine on, make sure that the voltage of your

electricity supply is the same as that indicated on the rating plate. This

product is designed to operate on 230 VAC mains power. Connecting it to

any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to

change the fuse in the plug, the fuse cover must be refitted. If the fuse cover

becomes lost or damaged, the plug must not be used until a suitable

replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or

due to damage, it should be cut off and a replacement fitted, following the

wiring instructions shown below. The old plug must be disposed of safely, as

insertion into a mains socket could cause an electrical hazard.

WARNING! The wires in the power cable of this product are

coloured in accordance with the following code:

Blue = Neutral Brown = Live Yellow and Green = Earth

If the colours of the wires in the power cable of this product do not

correspond with the terminal markings of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal

which is marked N or coloured Black.

• The wire which is coloured Brown must be connected to the

terminal which is marked L or coloured Red.

• The wire which is coloured Yellow and Green must be connected to

the terminal which is marked E or or coloured Green.

Plug must be BS1363/A approved

Earth Always fit a 13 Amp fuse.

(Green and Yellow)

Neutral Live

(Blue) (Brown)

Ensure that the outer sheath of the cable is firmly held by the clamp

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD).

If in doubt, consult a qualified electrician. DO NOT attempt repairs yourself.

OVERVIEW

This CLARKE range of submersible pumps are suitable for discharging pools,

ponds, fountains, pits and any waste water drainage.

SUITABILITY

They can handle foul water containing suspended material including sand as

listed in the specification, and may be used for pumping water, (including

seawater) or water containing solids in suspension. The pumps are not

suitable for handling inflammable, corrosive, explosive or dangerous liquids.

THE FLOAT SWITCH

The float switch enables the pump to stop and restart automatically as the

surrounding water level changes. As the water level rises, the switch will float

and start the pump. As the water level falls, so will the float switch, until it stops

the pump. Float switches are factory set to provide the correct ON-OFF

switching mode. This makes them suitable for permanent or semi-permanent

installations, eg. installations where it is necessary to maintain water at a

particular level without an operator in attendance.

THE THERMAL CUT-OUT

The pumps are provided with a thermal overload cut-out, so that in the event

that the pump becomes overheated (due to becoming blocked etc.) it will

shut off automatically. When the blockage has been cleared, the thermal

cutout will cool down and re-set and the pump can be re-started.

FLOAT SWITCH

STEPPED

ADAPTOR

MAINS CABLE LIFTING HANDLE

OUTLET

ELBOW

AIR VENT

FLOAT SWITCH

CABLE CLIP

WATER INLET

OPERATION

CONNECTION AND LOCATION

1. Screw the outlet elbow and stepped adaptor supplied, onto the outlet of

the pump.

2. Connect the outlet adaptor to the largest diameter hose available, as any

restriction will reduce capacity and put unnecessary strain on the motor.

• The stepped adaptor fitting allows for connection of 32 mm (1¼”), 25 mm

(1”), or 19 mm hoses which should be secured with a hose clamp.

3. Ensure that the hose diameter is as large as possible if a long run of

discharge hose is being used.

4. Place the pump in a vertical position resting on a firm, flat surface. If this is

not available, sit the pump on timber or house bricks, but ensure they are

not likely to collapse. Never install the pump on sand, silt, mud or ground

that is likely to collapse.

5. Keep the pump clear of sediment

by standing it on a platform or

brick or suspending from a rope

attached to the handle if the

pump is to be used where there

may be silt or mud etc (e.g.

garden ponds).

6. Ensure the float switch has

sufficient room to operate

correctly if used in a confined

space such as a shaft or sump.

• The pump should only be placed

in a sump which is large enough

not to restrict the movement of

the float switch.

Note: When the pump is being

used in a permanent or semi-permanent installation, a check

valve should be fitted in the delivery hose. Suitable hoses and

valves are available from your Clarke dealer.

USING THE PUMP

1. Plug in the pump and switch on the power supply,

• The pump will only run where there is sufficient water for the float switch to

rise and activate the pump.

2. If required, the range of operation of the float switch can be manually

adjusted by positioning the float switch cable within the retaining clip at

the top of the pump. The switch will operate through its full range if left

hanging free.

3. Run the pump continuously or remove from the water and store in a frost

free location if the water is likely to freeze,

4. Never run the pump dry. Ensure the pump switches off when water has

stopped flowing.

• The pump should be able to clear water down to a residual depth of

approx 5mm, provided the float switch has been raised to keep the pump

running. In this situation, air and residual water may be seen escaping

from the vent valve.

5. Disconnect from the power supply when the water has been pumped

out. Avoid running the pump continuously if the discharge hose has

become obstructed and water is not flowing.

AUTOMATIC THERMAL OVERLOAD

These pumps are fitted with automatic thermal overload protection. If the

pump overheats due to an obstruction in the pump, or pumping warm water

for example, it will shut off automatically.

Switch the pump OFF at the mains supply. Check for blockages and allow the

motor to cool (at least 5 minutes) before attempting to restart, by which time

the cut-out will have reset.

CLEANING & MAINTENANCE

WARNING: MAKE SURE THAT THE PUMP IS DISCONNECTED FROM THE

POWER SUPPLY BEFORE CLEANING, OR PERFORMING MAINTENANCE.

The pump should require no maintenance other than regular inspection and

cleaning.

1. Inspect the pump prior to use and do not use the pump if there is any

damage to the mains power cable or to the float switch or its connecting

cable.

2. Check pump regularly to ensure the inlet is clear of leaves or other debris.

It can be cleaned out either by back-flushing or by removing the base

plate (after undoing the three retaining screws) and cleaning out by

hand.

3. If the pump has been used for pumping swimming pool water or salty

water likely to leave chemical residues, it should be flushed through with

clean water before storage.

4. Store in a dry place after use.

If the pump shows signs of wear or damage, contact your CLARKE dealer for

advice. Do not attempt to repair the pump yourself, as you may damage the

waterproof seals and invalidate your guarantee. Repairs should be carried

out by your local CLARKE dealer, or contact the CLARKE Service Department

on 020 8988 7400.

ACCESSORIES

A wide range of accessories is available from your nearest CLARKE dealer,

including hoses and hose adaptors.

Andere Handbücher für PSV3A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Wasserpumpe Handbücher

Clarke

Clarke CBM240E Bedienungsanleitung

Clarke

Clarke HSE Series Installations- und Betriebshandbuch

Clarke

Clarke ISP14A Installations- und Betriebshandbuch

Clarke

Clarke CU150 Installations- und Betriebshandbuch

Clarke

Clarke CDDFTP Bedienungsanleitung

Clarke

Clarke BIP1500 Bedienungsanleitung

Clarke

Clarke CGP870 Bedienungsanleitung

Clarke

Clarke Hippo4A Bedienungsanleitung

Clarke

Clarke CS85S Installations- und Betriebshandbuch

Clarke

Clarke PF75 Bedienungsanleitung

Clarke

Clarke PSV3A Bedienungsanleitung

Clarke

Clarke PW50 Bedienungsanleitung

Clarke

Clarke PSV7A Bedienungsanleitung

Clarke

Clarke CM1 Installations- und Betriebshandbuch

Clarke

Clarke HIPPO-3 Handbuch

Clarke

Clarke DWP100A Bedienungsanleitung

Clarke

Clarke CPE30A3 Bedienungsanleitung

Clarke

Clarke CBB75 Bedienungsanleitung

Clarke

Clarke SUBMERSIBLE PUMP Bedienungsanleitung

Clarke

Clarke PSP195 Bedienungsanleitung

Clarke

Clarke CVPS Kurzanleitung

Clarke

Clarke PW80A Bedienungsanleitung

Clarke

Clarke ECP20A1 Bedienungsanleitung

Clarke

Clarke CSE400A Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung