Clarke PSV3A Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

GC04/17

SUBMERSIBLE PUMPS

MODEL NO: PSV3A, PSV4A, PSSV2A &

PVP11A

PART NO: 7236042, 7236044, 7236050 & 7236060

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Submersible Pump.

This pump is designed for pumping clean water only. it is not designed for

pumping slurry, sludge, mud or heavily polluted water, or any water containing

chemicals or other acidic contaminants including salt water.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

WORK AREA

1. Keep the work area clean and well lit. Floors should always be kept clear.

Cluttered or dark areas invite accidents.

2. Keep children and bystanders away while operating the pump.

Distractions can cause loss of control.

3. Remember, the operator or user is responsible for accidents or hazards

occurring to other people or their property.

PERSONAL SAFETY

1. Always stay alert, watch what you are doing and use common sense when

operating this pump. Do not install the pump while you are tired or under

the influence of medication, drugs or alcohol. A moment of inattention

can result in personal injury.

2. Do not over-reach. Keep your proper footing and balance at all times

when positioning the pump.

3. Never direct the water discharge towards electrical wiring or equipment.

4. Always store the pump out of reach of children and do not allow persons

unfamiliar with these instructions to operate it.

5. Never direct the discharge flow towards another person.

6. Always thoroughly familiarise yourself with this pump & its operation and

follow all instructions in this manual.

7. Always ensure that the pump is properly positioned where necessary to

prevent it from moving during operation, and that the immediate area

surrounding the pump is kept clear.

GENERAL USE AND CARE OF THE PUMP

1. An approved Residual Current Device (RCD) must be used when pumping

from ponds or swimming pools.

2. Always lift the pump using the handle and use a rope or chain attached if

necessary to lower it into the pit or excavation. Never lift or carry the pump

by the power cable or by the float switch cable.

3. Never use this pump if any part is damaged. Have it inspected and

repaired by your local Clarke dealer.

4. Always use an extension cable suitable for outdoor use when operating

outdoors. Using the correct cable reduces the risk of electric shock.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

5. Always maintain the pump with care and keep it clean.

6. Always use an approved cable extension suitable for the power rating of

the pump (see specifications). The conductor size should also be at least

the same size as that on the pump, or larger. When using a cable reel,

always unwind the cable completely.

7. Never use for pumping flammable liquids or corrosive chemicals. These

pumps are designed to pump water only.

8. Never abuse the electrical cable. Never use the cable for pulling or

unplugging the pump Damaged or tangled cables increase the risk of

electric shock.

9. Never run the pump dry. Always ensure the pump is immersed in water

before starting. Switch the pump OFF immediately the task is completed

10. Never pump water from a swimming pool when there is a person or animal

still in the pool.

11. Never install the pump on sand, silt or mud which is likely to shift or collapse.

12. Never modify this pump in any way. Use it only for the purpose for which it is

designed.

SERVICING & REPAIRS

1. Always have the pump serviced by your local CLARKE dealer, using only

identical replacement parts. This will ensure the safety of the pump is

maintained. The use of non standard parts could be hazardous.

2. Never attempt any repairs yourself. If you have a problem with the pump

contact your local CLARKE dealer.

3. Always disconnect the pump from the electrical supply before placing it

into, or removing from the water, and before any cleaning or

maintenance.

4. If the power cable becomes damaged, it must be replaced rather than

repaired.

Your CLARKE water pump has been designed to give long and trouble free

service. If, however, having followed the instructions in this booklet carefully,

you encounter problems, take the unit to your local CLARKE dealer.

Please keep these instructions in a safe place for future reference.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is

the same as that indicated on the rating plate. This product is designed to operate on

230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the

fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or

damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to

damage, it should be cut off and a replacement fitted, following the wiring instructions

shown below. The old plug must be disposed of safely, as insertion into a mains socket

could cause an electrical hazard.

If the colours of the wires in the power cable of this product do not correspond with the

markings on the terminals of your plug, proceed as follows.

• The wire which is coloured Blue must be connected to the terminal which is

marked Nor coloured Black.

• The wire which is coloured Brown must be connected to the terminal which

is marked Lor coloured Red.

• The wire which is coloured Yellow and Green must be connected to the

terminal which is marked E or or coloured Green.

We strongly recommend that this machine is connected to the mains supply

via a Residual Current Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE

MAINS SUPPLY.

WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT

ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

SUITABILITY

The CLARKE range of submersible pumps are suitable for discharging pools,

ponds, fountains, pits and any waste water drainage. They can handle foul

water containing suspended material as listed in the specification. The pumps

are not suitable for handling inflammable, corrosive, explosive or dangerous

liquids.

THE FLOAT SWITCH

The float switch enables the pump to stop and restart automatically as the

surrounding water level changes. As the water level rises, the switch will float

and start the pump. As the water level falls, so will the float switch, until it stops

the pump. Float switches are factory set to provide the correct ON-OFF

switching mode. This makes them suitable for permanent or semi-permanent

installations, eg. installations where it is necessary to maintain water at a

particular level without an operator in attendance.

THE THERMAL CUT-OUT

The pump is provided with a thermal overload cut-out, so that in the event

that the pump becomes overheated (due to becoming blocked etc) it will

shut off automatically. When the blockage has been cleared, the thermal

cutout will cool down and re-set and the pump can be re-started.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONNECTION AND POSITIONING

1. Screw the outlet elbow and

stepped adaptor supplied, onto

the outlet of the pump as shown.

2. Connect the outlet adaptor to

the largest diameter hose

available, as any restriction will

reduce capacity and put

unnecessary strain on the motor.

• The stepped adaptor fitting

allows for connection of 32 mm

(1¼”), 25 mm (1”), or 19 mm hoses which should be secured with a hose

clamp.

3. Ensure that the hose diameter is

as large as possible if a long run of

discharge hose is being used.

• Suitable hoses are available

from your local Clarke dealer.

POSITIONING THE PUMP

1. ALWAYS raise and lower the pump

using a rope attached to the

lifting handle.

2. Place the pump in a vertical

position resting on a firm, flat

surface in the area that you want

to drain. If there is sediment in the

operating area, the pump should

be placed vertically on house bricks, or similar but ensure they are not likely

to collapse. Never install the pump on sand, silt, mud or ground that is likely

to collapse.

3. Keep the pump clear of sediment by standing it on a platform or brick or

suspending from a rope attached to the handle if the pump is to be used

where there may be silt or mud etc (e.g. garden ponds).

4. Ensure the pump is positioned with adequate space so that the movement

of the float switch is not restricted - recommended minimum area of 50 x

50cm.

5. Allowance must also be made for the overall width of the pump including

the outlet elbow on one side.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

6. Ensure the float switch has

sufficient room to operate

correctly if used in a confined

space such as a shaft or sump.

• The pump should only be

placed in a sump which is large

enough not to restrict the

movement of the float switch.

• When the pump is being used

in a permanent or semi-

permanent installation, a non-

return valve should be fitted in

the delivery hose. Suitable

hoses and valves are available

from your Clarke dealer.

USING THE PUMP

1. Plug in the pump and switch on the power supply.

• Always use a high sensitivity residual current device (RCD) which has a

tripping current of less then 30mA.

• The pump will only run where there is sufficient water for the float switch

to rise and activate the pump.

2. If required, the range of operation of the float switch can be manually

adjusted by positioning the float switch cable within the retaining clip at

the top of the pump. The switch will operate through its full range if left

hanging free.

3. Run the pump continuously or remove from the water and store in a frost

free location if the water is likely to freeze.

4. Never run the pump dry. Ensure the pump switches off when water has

stopped flowing.

• The pump should be able to clear water down to a residual depth of

approx 5mm, provided the float switch has been raised to keep the

pump running. In this situation, air and residual water may be seen

escaping from the vent valve.

5. Disconnect from the power supply when the water has been pumped out.

Avoid running the pump continuously if the discharge hose has become

obstructed and water is not flowing.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

AUTOMATIC THERMAL OVERLOAD

These pumps are fitted with automatic thermal overload protection. If the

pump overheats due to an obstruction in the pump, or pumping warm water

for example, it will shut off automatically.

Switch the pump OFF at the mains supply. Check for blockages and allow the

motor to cool (at least 5 minutes) before attempting to restart, by which time

the cut-out will have reset.

CLEANING, MAINTENANCE & STORAGE

The pump should require no maintenance other than regular inspection and

cleaning.

1. Inspect the pump prior to use and do not use the pump if there is any

damage to the mains power cable or to the float switch or its connecting

cable.

2. Check pump regularly to ensure the inlet is clear of leaves or other debris. It

can be cleaned out either by back-flushing or by removing the base plate

(after undoing the retaining screws) and cleaning out by hand.

3. If the pump has been used for pumping swimming pool water or salty

water likely to leave chemical residues, it should be flushed through with

clean water before storage.

4. When the pump is not being used for extended periods, clean and dry it

thoroughly and store in indoors. if the pump is left in water, it should be run

at least once a week to prevent it from seizing up.

If the pump shows signs of wear or damage, contact your CLARKE dealer for

advice. Do not attempt to repair the pump yourself, as you may damage the

waterproof seals and invalidate your guarantee. Repairs should be carried out

by your local CLARKE dealer, or contact the CLARKE Service Department on

020 8988 7400.

ACCESSORIES

A wide range of accessories is available from your nearest CLARKE dealer,

including hoses and hose adaptors.

WARNING: MAKE SURE THAT THE PUMP IS DISCONNECTED FROM THE

POWER SUPPLY BEFORE CLEANING OR PERFORMING MAINTENANCE

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TROUBLESHOOTING

PROBLEM SOLUTION

Pump hums

but does not

run

1. Impeller partially clogged. Raise pump and clean.

• If pump is clear, motor could be defective.

Pump runs but

does not

deliver water

or only delvers

a small

amount

1. Check or non-return valve is installed backwards. Arrow

on valve should point in direction of flow.

2. Discharge shut-off valve if used, may be closed. Check

that the outlet is not clogged or obstructed.

3. Impeller partially clogged. Raise pump and clean.

4. Air bubble in the pump, produced during immersion.

immerse the pump again, at an angle, and shake it whilst

lowering to remove any air trapped in the system.

5. Inlet at base of pump is blocked. Raise pump and clear

openings.

6. Vertical pumping distance too high. Reduce height or

change the pump discharge fitting.

7. Impeller may be damaged - Consult your CLARKE dealer.

Pump runs but

will not stop

1. Float switch may be prevented from moving to the fully

down position.

2. Faulty float switch. Consult your CLARKE dealer.

Pump will not

start

1. Make sure that the power is switched on.

2. Check fuse (consult an electrician if in doubt).

3. If an extension lead is fitted, check connections (consult

an electrician if in doubt).

4. Internal thermal cut-out has not re-set. Leave for 5-10

minutes and try again.

5. The impeller may be jammed. Disconnect from the mains

supply and remove any objects that may be obstructing

the impeller.

6. Float switch may be jammed against side wall, or

prevented from moving.

7. If the pump still fails to start, consult your CLARKE dealer

for advice.

Andere Handbücher für PSV3A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Wasserpumpe Handbücher

Clarke

Clarke DWP400A Bedienungsanleitung

Clarke

Clarke LVP1A Bedienungsanleitung

Clarke

Clarke CPP3000B Bedienungsanleitung

Clarke

Clarke CU150 Installations- und Betriebshandbuch

Clarke

Clarke SUBMERSIBLE PUMP Bedienungsanleitung

Clarke

Clarke CVPW Kurzanleitung

Clarke

Clarke ECP20A1 Bedienungsanleitung

Clarke

Clarke IVP14A Bedienungsanleitung

Clarke

Clarke CWBP300 Bedienungsanleitung

Clarke

Clarke CPE Series Bedienungsanleitung

Clarke

Clarke CBT1300SS Bedienungsanleitung

Clarke

Clarke CSE400A Installations- und Betriebshandbuch

Clarke

Clarke CPRP560 Bedienungsanleitung

Clarke

Clarke BIP1500 Bedienungsanleitung

Clarke

Clarke PSV3A Installations- und Betriebshandbuch

Clarke

Clarke ISP14A Installations- und Betriebshandbuch

Clarke

Clarke CPPRSS Bedienungsanleitung

Clarke

Clarke Hippo4A Bedienungsanleitung

Clarke

Clarke CPE20A1 Bedienungsanleitung

Clarke

Clarke CSE2 Bedienungsanleitung

Clarke

Clarke PSV1A Bedienungsanleitung

Clarke

Clarke GSE1 Bedienungsanleitung

Clarke

Clarke CBB75 Bedienungsanleitung

Clarke

Clarke CBM100SS Installations- und Betriebshandbuch

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung