ClearSpan Cedar 8' Wide End Frame Kit Bedienungsanleitung

CLEARSPAN™END FRAME KIT

Revision date: 05.18.10

is prohibited without permission.

ClearSpan™

Cedar 8' Wide End Frame Kit

Photo may show a different but similar model.

STK # WIDTH

105363 8'

CLEARSPAN™END FRAME KIT

2Revision date: 05.18.10

YOU MUST READ THIS DOCUMENT BEFORE YOU

BEGIN TO ASSEMBLE THE SHELTER.

Thank you for purchasing this ClearSpan™ End Frame Kit.

When properly assembled and maintained, this product will

provide years of reliable service. These instructions include

helpful hints and important information needed to safely

assemble and properly maintain the end frame. Please

read these instructions before you begin.

If you have any questions during the assembly, contact

Customer Service for assistance.

SAFETY PRECAUTIONS

• Wear eye protection.

• Wear head protection.

• Wear gloves when handling the materials.

• Use a portable GFCI (Ground Fault Circuit Interrupter)

when working with power tools and cords.

• Do not climb on the shelter or framing during or after

construction.

• Do not occupy the shelter during high winds,

tornadoes, or hurricanes.

• Provide adequate ventilation if the structure is

enclosed.

• Do not store hazardous materials in the shelter.

• Provide proper ingress and egress to prevent

entrapment.

WARNING: The individuals assembling this structure

are responsible for designing and furnishing all

temporary bracing, shoring and support needed during

the assembly process. For safety reasons, those who

are not familiar with recognized construction methods

and techniques must seek the help of a qualified

contractor.

REQUIRED TOOLS

The following list identifies the main tools needed to

assemble the end frame. Additional tools and supports may

be needed depending on the structure, location, and

application.

• Tape measure or measuring device

• Variable speed drill and impact driver (cordless with

extra batteries works best)

• Wrenches and impact socket set, or an adjustable

wrench

• Scissors or utility knife

• Hammers and gloves

• Ladders, work platforms, and other machinery for lifting

designed to work safely at the height of the building

and end frame.

ASSEMBLY PROCEDURE

Following the instructions as presented will help ensure the

proper assembly of your end frame. The steps outlining the

assembly are as follows:

1. Verify that all parts are included in the shipment. Notify

Customer Service for questions or concerns.

2. Read these instructions and all additional

documentation included with the shipment before you

begin.

3. Gather the tools, bracing, ladders (and lifts), and

assistants needed for assembly.

4. Check the weather before you install the film (if

equipped). Do not install covers or panels on a windy

or stormy day.

5. Assemble the end frame.

6. Read the care and maintenance information.

7. Complete and return all warranty information (if

included) as instructed.

CLEARSPAN™END FRAME KIT

Revision date: 05.18.10

UNPACK AND IDENTIFY PARTS

The following steps will ensure that you have all the

necessary parts before you begin to assemble the end

frame.

1. Unpack the contents of the shipment and place where

you can easily inventory the parts. Refer to the Bill of

Materials/Spec Sheets.

2. Verify that all parts listed on the Bill of Materials/Spec

Sheets are present. If anything is missing or you have

questions, consult the Pictorial Parts Guide and all

shelter diagrams for clarification, or contact Customer

Service.

NOTE: At this time, you do not need to open the plastic

bags containing smaller parts such as fasteners and

clamps.

SHELTER CARE AND MAINTENANCE

Proper care and maintenance of your ClearSpan™ building

is important. Check the following items periodically to

properly maintain your building:

• Regularly check the main cover and end panels to see

that these remain tight and in proper repair.

• Frequently check the anchoring system and all

components. Replace worn or damaged parts

immediately.

• Check all fasteners frequently to verify that these

remain tight and in good repair.

• Do not climb or stand on the building or frame at

anytime.

• Remove debris and objects that may accumulate on

the shelter. Use tools that will not damage the cover

when removing debris.

• Remove snow to prevent excess accumulation. Use

tools that will not damage the cover when removing

snow. Never allow snow to accumulate on the main

cover or to remain against the sides or end panels after

it is removed from the main cover.

• Check the contents of the shelter to verify that

nothing is touching the cover or panels that could

cause damage.

• Replace all worn or damaged parts.

• For replacement or missing parts, call 1-800-245-9881

for assistance.

NOTE: With the exception of Truss Arch buildings,

ClearSpan™ shelters and greenhouses do not have any

tested loading criteria.

CLEARSPAN™END FRAME KIT

4Revision date: 05.18.10

The following graphics and photos will help you identify the

different parts of the end frame. Consult the diagrams for

additional details. (Some parts are not shown.)

105107

1.05" Fabric Clip

CC6212

1.315" Fabric Clip

102197

Aluminum U-Channel

102198

U-Channel Spring

FA4482B

Tek Screw

100441

Nut Setter

FAF25PB

Phillips Head Screws

FAS8

Square Head Screws

104638

Tee Connector

CLEARSPAN™END FRAME KIT

Revision date: 05.18.10

OVERVIEW

This section describes assembling your end frame kit. See

illustration below to identify main parts of end frame kit.

1. Locate the required parts for each assembly procedure.

2. Assemble and attach all end wall framing.

3. Prepare and attach end panel film.

ClearSpan™

Cedar 8' Wide End Frame Kit

Photo may show a different but similar model.

Ground Level

Drawing may show a different but similar model.

Exploded drawings do not

show the film end panel.

Ground Level

View as seen

from the inside

of the shelter.

View as seen from the outside of the shelter.

CLEARSPAN™END FRAME KIT

6Revision date: 05.18.10

1INSTALL ANGLE ANCHORS

Ground Level

Drawing may show a different but similar model.

Gather the parts:

• #105232 Angle Anchors

View the diagrams to measure and determine the location

of the two (2) angle anchors for the two door jambs.

1. Mark the center of the shelter's end rafter by

measuring the distance between the two ground

posts and dividing in half.

2. Measure 13-7/16" in both directions from the center

mark and push the two (2) angle anchors into the

ground leaving at least 3" exposed. Anchors must

be straight and evenly spaced. Refer to the diagram

below.

NOTE: Place the anchors so the door jamb sits

directly in line with the ground posts.

3. Continue with the information on the following page to

assemble and install the door jambs.

Diagram shows position of angle anchors measured from the center mark.

Center

13-7/16" 13-7/16"

Ground

Post

Ground

Post

105232

Angle

Anchor

105232

Angle

Anchor

Outside of Shelter

oor

amb

oor

amb

TOP VIEW

* DIAGRAM NOT TO SCALE.

CLEARSPAN™END FRAME KIT

Revision date: 05.18.10

2INSTALL DOOR JAMBS

Gather the parts:

• Door jambs (#EG08W1200)

• Square head screws (#FAS8)

• 1.05" Fabric clips (#105107)

• Tek screws (#FA4482)

Consult the diagrams to assemble and attach the two (2)

door jambs.

1. Gather the two (2) door jambs and the two (2) 105107

fabric clips. Attach the fabric clips to the angled ends

of the jambs using a FAS8 square head screw. Drill a

hole through the fabric clip if needed. Center the clip

on the angled cut.

2. Set assembled door jambs into position by seating the lower end of the door jambs into the angled anchors and

clipping the top of the door jambs with the fabric clips onto the rafter. Verify the jambs are straight and evenly

spaced.

3. Once in position, secure clips by installing a Tek screw through the clip and into the rafter from the inside of the

shelter.

4. Secure lower ends of the door jambs by installing two square head construction screws through each angle anchor

and into the door jamb from the outside of the shelter. Pre-drill the holes through the anchor stake for each FAS8

screw.

Ground Level

Step 1 & 3

Step 4

Step 1

FAS8

105107

EG08W1200

Inside of

shelter

Outside of

shelter

FAS8

Ground

Level

Step 4

Tek screw

Step 3

Views above are seen from the

inside of the shelter.

Ground

Level

EG08W1200 EG08W1200

Angled Anchors

Drawings may show a different but similar model.

Outside View

CLEARSPAN™END FRAME KIT

8Revision date: 05.18.10

3ASSEMBLE AND ATTACH FRAME BRACES

Gather the parts:

• Outer frame braces (#EG08W1202)

• Middle frame brace (#EG00W1201)

• Square head screws (#FAS8)

• 1.315" Fabric clips (#CC6212)

• Tee Connectors (#104638)

• Phillips head screws (#FAF25P)

• Tek screws (#FA4482)

View the diagrams to assemble and attach the two (2)

frame braces.

1. Gather the two (2) outer frame braces and the two (2) CC6212 fabric clips. Attach each fabric clip to the end of a

frame brace using a FAS8 square head screw. Center the clip on the brace end as shown below.

2. Set assembled frame braces into position by seating the plain end against the door jambs and clipping the fabric

clip to the ground post. Verify the braces are straight and level. (Push fabric clips into the ground if needed.)

3. Once in position, secure fabric clips by installing a Tek screw through the clip and into the ground post from the

inside of the shelter. Drill a hole through the fabric clip if needed.

4. Place the EG00W1201 middle frame between the door jambs. Verify the brace is straight and level.

5. Secure the braces to the door jamb from the inside of the shelter by attaching a 104638 tee connector using

FAF25P Phillips head screws. Position tee so it does not contact the anchor stake.

Frame is seen from the inside of the shelter.

Ground Level

EG08W1202 EG08W1202

Drawing may show a different but similar model.

EG00W1201

Ground Level

EG08W1202

EG00W1201

EG08W1202

Step 1 & 3 Step 4

Views as seen from the

inside of the shelter.

EG08W1202CC6212FAS8

Step 1

FA4482B

Ground Level

Ground Post

Step 3

FAF25P

Step 4

104638

EG08W1202

Ground Level

Inside View

CLEARSPAN™END FRAME KIT

Revision date: 05.18.10

4INSTALL FILM END PANELS

Ground Level

End panel installed. View as seen from outside the building.

Gather the parts:

• End panel film

• Poly latch U-channel (#102197)

• Spring for U-channel (#102198)

• Tek screws (#FA4482)

View the diagrams to install the poly latch U-channel and

attach the end panel film.

1. Using Tek screws, attach sections of the poly latch

U-channel along the outside of the frame base as

shown in the diagrams.

NOTE: If main cover is installed, detach the main cover

from the end rafter. Reinstall main cover after end film

has been installed.

2. Unfold and position the end film over the end rafter. Drape some of the material over the top rafter leaving enough

to reach the ground plus 6" - 12". Center the film so equal excess material is on each side of the shelter. Tape can

be used to temporarily hold material in place if needed.

3. Once end film is in position, attach the film to the end rafter starting at the top of the end rafter. If U-channel is

present, work your way down each side and wiggle the wire spring back and forth to seat the spring into the

previously installed U-channel. Holding the film in place and pull it tight while working down the end rafter.

4. Install the remaining springs into the

U-channel attached along the frame base.

Pull the cover snug while installing the

spring.

View as seen from outside the building.

Step 1

Step 4

Drawing may show a different but similar model.

Space Tek screws evenly about 24" apart.

102197

FA4482B

Ground

Level

Step 1

Always wear eye protection when

installing the 102198 spring!

CAUTION: Risk of Injury

DO NOT REMOVE TOO MUCH OF THE

EXCESS FILM MATERIAL. Some excess

end film material–the material that extends

beyond the U-channel–should remain

in place. If the film needs stretched in

the future, remove the spring from the

U-channel, grasp the excess material, pull

the film tight, and reinstall the spring.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ClearSpan Gewächshaus-Bausatz Handbücher

ClearSpan

ClearSpan Premium Solar Star 104918 Bedienungsanleitung

ClearSpan

ClearSpan CL108550 Bedienungsanleitung

ClearSpan

ClearSpan Gothic Style Solar Star Bedienungsanleitung

ClearSpan

ClearSpan 500 Cold Frame Series Bedienungsanleitung

ClearSpan

ClearSpan 106417 Bedienungsanleitung

ClearSpan

ClearSpan R020B00008 Bedienungsanleitung

ClearSpan

ClearSpan CL108545 Bedienungsanleitung

ClearSpan

ClearSpan Pro Solar Star R030 Handbuch

ClearSpan

ClearSpan R020B00000F Bedienungsanleitung

ClearSpan

ClearSpan Majestic Greenhouse Bedienungsanleitung

ClearSpan

ClearSpan Beef Master 108441W Bedienungsanleitung

ClearSpan

ClearSpan Cedar 12' Wide End Frame Kit with Dutch Door Bedienungsanleitung

ClearSpan

ClearSpan R030B00008 Bedienungsanleitung

ClearSpan

ClearSpan ClearSpan 104950F Bedienungsanleitung

ClearSpan

ClearSpan 30' Wide Pony Wall Building Bedienungsanleitung

ClearSpan

ClearSpan 34' Wide Pony Wall Building Bedienungsanleitung

ClearSpan

ClearSpan Premium Moo-Tel Series Bedienungsanleitung

ClearSpan

ClearSpan EZ-Grow Greenhouse Bedienungsanleitung

ClearSpan

ClearSpan Pro Solar Star Bedienungsanleitung

ClearSpan

ClearSpan PB00816R4 Bedienungsanleitung

ClearSpan

ClearSpan CL108547 Bedienungsanleitung

ClearSpan

ClearSpan Gothic Style Cold Frame Bedienungsanleitung

ClearSpan

ClearSpan EZ-Growl Bedienungsanleitung

ClearSpan

ClearSpan CL108552 Bedienungsanleitung

Beliebte Gewächshaus-Bausatz Handbücher anderer Marken

ACD PRESTIGE

ACD PRESTIGE MR3 H Bedienungsanleitung

Vitavia

Vitavia VA0040-TRP Bedienungsanleitung

VegTrug

VegTrug Nursery Bedienungsanleitung

Riverstone Networks

Riverstone Networks Monticello 041315V Bedienungsanleitung

STC

STC Easy Grow 6x12 Greenhouse Bedienungsanleitung

CLIMA POD

CLIMA POD Spirit V7 Series Bedienungsanleitung

Vitavia

Vitavia GAIA JUMBO Bedienungsanleitung

Palram

Palram Harmony 6'x4' Bedienungsanleitung

Sproutwell

Sproutwell GRANGE - 5 Bedienungsanleitung

ACD

ACD Piccolo 03 Bedienungsanleitung

Growhouse

Growhouse Lean To 6 x 8 Bedienungsanleitung

Riverstone Networks

Riverstone Networks Grower's 181010V Bedienungsanleitung

GrowSpan

GrowSpan 500 Series Bedienungsanleitung

Robinsons

Robinsons 5ft Wide LEAN-TO Bedienungsanleitung

Botanica

Botanica E Bedienungsanleitung

PNI

PNI SP6000 Bedienungsanleitung

Hortus

Hortus 211-203 Programmierhandbuch

Robinsons

Robinsons 6' Lean-To Bedienungsanleitung