ClearSpan R030A00007 Bedienungsanleitung

Revision date: 04.13.09

is prohibited without permission.

Diagram shows the end wall kit without a door. (Door purchased separately.)

ClearSpan™

Corrugated Polycarbonate End Panel Kit

30' Wide & 35' Wide

STK#

R030A00007 (30' Wide)

R035A00007 (35' Wide)

2Revision date: 04.13.09

CORRUGATED PC PACKAGE: READ THIS BEFORE

YOU BEGIN

The corrugated PC package accessory is designed to

attach to the end wall framing kit (R035A00001) after the

end frame is assembled.

Choose one of the following options to continue:

If you purchased but have not assembled the•

R035A00001 end frame, stop here, return to the

end frame instruction guide, and continue with those

instructions.

If you did not purchase the R035A00001 end wall•

kit but plan to construct an end wall using customer-

supplied materials, review these instructions before

constructing the end wall to better prepare for the

installation of the panels included in this PC package.

After assembling the end frame, continue with these

instructions to attach the corrugated polycarbonate panels

to the end wall.

ATTENTION: If you purchased an optional door kit,

consult those instructions and proceed as instructed. In

most instances, the end wall frame and door frame are

constructed before end panels are installed. This allows

for the placement of panels as determined by the position

of the door or doors.

It is the responsibility of the owner/contractor to adjust the

position of the end wall panels based on the end frame

and the position of the installed door or doors.

Table of Contents

Important Information ....................................... 3

End Panel Installation ....................................... 5

Shelter Care and Maintenance ......................... 8

Quick Start Guide .............................................. 9

Polycarbonate Panels - 30' Wide ............... 10

Polycarbonate Panels - 35' Wide ............... 11

IMPORTANT: Some diagrams throughout this manual

show the edges of the end panels installed in line with

the centers of the end rafter leg/ground posts.

For buildings that include sidewall polycarbonate panels

and hat channel secured to the frame, shift the position

of the end panels as needed so these panels meet the

sidewall panels and create a finished corner.

FRAMING: None of the frame members (rafter, ground

posts, etc.) supporting the end panels is included in

the end panel kit. Only those components needed to

attach the end panels to an existing frame are included.

Fasteners are designed for metal. If your end wall

frame requires different fasteners, contact your sales

representative to purchase additional fasteners, or

purchase the proper fasteners locally.

Revision date: 04.13.09

Important Information

YOU MUST READ THIS DOCUMENT BEFORE YOU

BEGIN TO ASSEMBLE THE END WALL KIT.

Thank you for purchasing this ClearSpan™ Corrugated

Polycarbonate Kit. When properly assembled and

maintained, this product will provide years of reliable

service. These instructions include helpful hints and

important information needed to safely assemble

and properly maintain the panels. Please read these

instructions before you begin.

SAFETY PRECAUTIONS

Wear eye protection.•

Wear head protection.•

Use a portable GFCI (Ground Fault Circuit•

Interrupter) when working with power tools and cords.

Do not climb on the shelter or framing during or after•

construction.

Do not occupy the shelter during high winds,•

tornadoes, or hurricanes.

Provide adequate ventilation if the structure is•

enclosed.

Do not store hazardous materials in the shelter.•

Provide proper ingress and egress to prevent•

entrapment.

WARNING: The individuals assembling this end

wall are responsible for designing and furnishing

all temporary bracing, shoring and support needed

during the assembly process.

For safety reasons, those who are not familiar with

recognized construction methods and techniques

must seek the help of a qualified contractor.

REQUIRED TOOLS

The following list identifies the main tools needed to

assemble the end wall. Additional tools and supports may

be needed depending on the structure, location, and

application.

Tape measure or measuring device•

Fine point marker to mark the location on panels.•

Variable speed drill and impact driver (cordless with•

extra batteries works best)

Scissors or utility knife and tool to cut the•

polycarbonate panels

Hammers, gloves and eye protection•

Ladders, work platforms, and other machinery for•

lifting designed to work safely at the height of the

building and end wall.

ATTENTION: Consult the services of a qualified,

professional contractor if you are not familiar with the

construction of similar frame structures.

SEALANT APPLICATION (OPTIONAL)

The application of sealant is left to the discretion of the

owner/contractor. If used during panel installation, apply

a sealant recommended for exterior use and that remains

flexible when cured. To create a better seal, apply sealant

between adjacent panels where the panels overlap each

another. Sealant is not included with the building and must

be supplied by the customer.

Sealant

Rib Overlap Corrugated Panel

4Revision date: 04.13.09

FA4482B

Tek Screw

104621C

Corrugated Polycarbonate Panels

102921B

Neo-bonded

Galvanized Washers

100441

Nut Setter

Important Information

ASSEMBLY PROCEDURE

Following the instructions as presented will help ensure

the proper installation of the end panels. The steps

outlining the assembly process are as follows:

Verify that all parts are included in the shipment.1.

Notify Customer Service for questions or concerns.

Read these instructions, the Must Read document,2.

and all additional documentation included with the

shipment before you begin.

Gather the tools, bracing, ladders (and lifts), and3.

assistance needed to install the end panels.

Check the weather4. before you install the panels. Do

not install panels on a windy or stormy day or when

such conditions are expected.

Install the panels.5.

Read the care and maintenance information at the6.

end of these instructions.

Complete and return all warranty information as7.

instructed.

PARTS IDENTIFICATION

The following graphics and photos will help you identify

the different parts. (Some parts are not shown.)

UNPACK AND IDENTIFY PARTS

The following steps will ensure that you have all the

necessary parts before you begin.

Unpack the contents of the shipment and place1.

where you can easily inventory the parts. Refer to the

Bill of Materials/Spec Sheets.

Verify that all parts listed on the Bill of Materials/Spec2.

Sheets are present. If anything is missing or you

have questions, consult the parts guide on the next

page and all shelter diagrams for clarification, or

contact customer service.

NOTE: At this time, you do not need to open the

plastic bags containing smaller parts such as

fasteners and clamps.

QUICK START GUIDE

For a quick overview of the end wall and its components,

consult the Quick Start Guide located at the back of

these instructions.

Revision date: 04.13.09

End Panel Installation

END PANEL INSTALLATION

The steps that follow describe one way to complete the

end wall panel installation.

The materials and parts needed to assemble the end

panels include:

Corrugated polycarbonate panels (#104621C)•

Tek screws (#FA4482B)•

Neo-bonded washers (#102921B)•

Read the following information before starting:

Tek screws and neo-bonded washers are used to•

secure panels to end wall frame.

During preparation, rest the edges of the panels on•

cardboard or other material to protect them from dirt

and damage.

Consult the polycarbonate panels (Quick Start•

section) for the location and lengths of each panel.

The diagrams are located at the back of these

instructions.

ATTENTION: Panels must be positioned as shown on the

panel diagrams. Using a panel in the incorrect place can

affect the placement of subsequent panels.

Install all accessories (fans, vents, heaters, etc.) after

installing all polycarbonate sheets.

Complete the following steps to install the end wall panels.

Consult the polycarbonate panels diagrams located in the

Quick Start section, select one panel, begin at the edge

of the end wall, and work toward the opposite edge of the

end wall.

NOTE: Set end panels in a position that prepares for the

installation of the sidewall panels if equipped. This may

include shifting the outside panels beyond the end rafter

leg/ground post so corner panels align with each other.

Set the first 50" x 12' 2" panel in place as shown with1.

the side edge aligned with the center of the end rafter

and the bottom edge flush against the ground. Do not

attach at this time.

If a door accessory was purchased, install the

door before attaching the end panels. Adjust the

panel position as needed to accommodate the door

installation. Consult the door installation manual (if

present) for additional details.

Actual end frame may differ from frame shown; end panel

installation is the same. Consult the panel diagrams located

in the Quick Start section for your end panel kit.

Trim excess

panel

Brace panel in correct position

and trace a line along the end

rafter. Remove panel and cut

to fit.

Adjust panels as needed to

create a finished corner joint

where end panels meet sidewall

panels. See arrows to the left.

50" x 12' 2"

Panel

Trace along the end rafter to mark where the panel2.

needs to be cut to fit into the end cap.

Remove panel, cut along traced line, and set panel3.

back into position by tucking the top edge under the

end cap. Do not damage panel section cut from main

panels; these may be used in another position.

Verify that the panel is flush with the ground and that4.

the outer edge is aligned so that it creates a finished

corner with the sidewall panels (if equipped) when

these are installed. Attach panel to the end frame.

End Cap

Position top of

end panels here

Typical End

Rafter Position

6Revision date: 04.13.09

End Panel Installation

END PANEL INSTALLATION (continued)

Secure the panel to the end frame girt using Tek5.

screws and neo-bonded washers inserted every 6" or

so (see drawing A).

Do not install Tek screw into the valley where the next

panel overlaps the first. See diagram B.

Select another 50" x 12' 2"6. panel and brace it in place,

overlapping the first panel by one (1) rib as shown in

drawing B. Do not attach at this time.

Holding the panel in place, repeat steps 2 through 57.

to mark, trim, and attach panel to the end frame. DO

NOT attach the panel to the top girt at this time. See

diagram below.

NOTE: Leave the innermost valley open for the

installation of the next panel; panels overlap by one

(1) rib. See diagram below for girt positions.

Continue attaching 50" x 12' 2" panels in this fashion8.

until the bottom row of end panels is complete. Cut

the final panel to fit as needed.

Remember to account for the installation of the

sidewall panels if equipped. Position and cut final

panel as needed.

Valley

Corrugated Panel

Girt

TOP VIEW

Ground Level

50" x 12' 2"

panel

50" x 12' 2"

panel

Girt

Trim

excess panels

Trim

excess panels

Actual end frame and panels may differ from frame

shown. Consult the panel diagrams located in the

Quick Start section for the end kit ordered.

Do not attach panels to the top girt. Tek

screws are installed after the top panels

are set into place. Top panels overlap

lower panels. Typical overlap is 6".

Rib

Corrugated Panel

No Tek screw in

this valley. No Tek screw in

this valley.

Girt

TOP VIEW

Revision date: 04.13.09

Sample End Wall Complete

End Panel Installation

END PANEL INSTALLATION (continued)

With the bottom row of panels installed, measure from9.

the top of the end rafter to the bottom of the top girt.

Use this measurement to cut the first section of a10.

50" x 12' 2" panel. Typical overlap is 6".

Holding the pre-cut panel in place, trace along the end11.

rafter to mark where the panel needs to be cut to fit

under the end cap.

Remove panel, cut along traced line, and set panel12.

back into position by tucking the top edge under the

end cap. The top panel overlaps the lower panel.

Verify the bottom edge of the panel aligns with the top13.

girt and attach the top panel to the end frame using

Tek screws and washers.

Continue measuring, cutting and installing the14.

remaining sections of the 50" x 12' 2" panel until the

top row is complete.

Continue by reading the care and maintenance15.

section that follows.

Secure panel by installing Tek screws through both the

top and bottom panels and into the girt.

Measure from the top

of the end rafter to the

bottom of the top girt.

Trim excess panel

Tek screws

and washers

Ground Level

8Revision date: 04.13.09

Space below is reserved for customer notes.

Shelter Care and Maintenance

SHELTER CARE AND MAINTENANCE

Proper care and maintenance of the end panels is

important. Check the following items periodically to

properly maintain the end wall:

Regularly check the polycarbonate panels to see•

that these are secure and in good condition. Replace

damaged panels if needed.

Check connections and all fasteners to verify that they•

remain tight.

Do not climb or stand on the shelter at anytime.•

Inspect the anchoring system to verify that all•

components remain tight and in good condition.

Remove debris and objects that can accumulate on•

the shelter. Use tools that will not damage the panels

when removing debris.

Do not allow snow to pile up against the end wall•

and panels. Use tools that will not damage the

polycarbonate panels when removing snow.

Check the contents of the shelter to verify that nothing•

is touching the polycarbonate panels that could cause

damage.

If the shelter is moved, inspect all parts and•

connections before it is reassembled.

Depending on the contents, construction of the shelter,•

shelter materials, and shelter location, the potential for

condensation exists. ClearSpan™ offers several items

that can be used to alleviate a condensation condition.

Please contact a ClearSpan™ representative for

additional information.

For replacement or missing parts, call 1-800-245-9881•

for assistance.

NOTE: With the exception of Truss Arch buildings or as

otherwise noted, ClearSpan™ shelters and greenhouses

do not have any tested loading criteria.

Revision date: 04.13.09

QUICK START GUIDE

30' and 35' Wide End Panels

Quick Start Guide

IMPORTANT: Diagrams throughout this manual show the

end panels installed in line with the centers of the end

rafter leg/ground posts.

For buildings that include sidewall polycarbonate panels,

shift the position of the end panels as needed so these

panels meet the sidewall panels and create a finished

corner.

30' Wide Sample Panel overlap

seams.

Ground Level

Top edge of the

lower panels.

35' Wide Sample

Ground Level

10 Revision date: 04.13.09

Polycarbonate Panels - 30' Wide

4'-2"

12'-2"

Rib

Corrugated

Panel

Corrugated

Panel

Girt

TOP VIEW

Each panel overlaps the previously installed

panel by one (1) rib.

Create all top panels from

one (1) 50" x 12' 2" panel.

Panel diagram is shown without end framing for clarity.

Ground Level

If a door was purchased, position panels

as needed to accommodate the door

installation. Install door or doors before end

panels.

Diagram below shows the installed sidewall

hat channel used for the installation of the

sidewall polycarbonate panels of the main

building.

(approximate

width)

Sidewall Hat

Channel

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ClearSpan Gewächshaus-Bausatz Handbücher

ClearSpan

ClearSpan 104903 Bedienungsanleitung

ClearSpan

ClearSpan ClearSpan 104950F Bedienungsanleitung

ClearSpan

ClearSpan Pro Solar Star R030 Handbuch

ClearSpan

ClearSpan 104881 Bedienungsanleitung

ClearSpan

ClearSpan CL108550 Bedienungsanleitung

ClearSpan

ClearSpan Super Moo-Tel Building 38' Wide Bedienungsanleitung

ClearSpan

ClearSpan CL108547 Bedienungsanleitung

ClearSpan

ClearSpan Beef Master 108441W Bedienungsanleitung

ClearSpan

ClearSpan 30' Wide Pony Wall Building Bedienungsanleitung

ClearSpan

ClearSpan Pro Solar Star Bedienungsanleitung

ClearSpan

ClearSpan 34' Wide Pony Wall Building Bedienungsanleitung

ClearSpan

ClearSpan Premium Solar Star Bedienungsanleitung

ClearSpan

ClearSpan 104895 Bedienungsanleitung

ClearSpan

ClearSpan Premium Solar Star 104918 Bedienungsanleitung

ClearSpan

ClearSpan Premium Moo-Tel Series Bedienungsanleitung

ClearSpan

ClearSpan 104828PCA Bedienungsanleitung

ClearSpan

ClearSpan 104900 Bedienungsanleitung

ClearSpan

ClearSpan CL108548 Bedienungsanleitung

ClearSpan

ClearSpan 106265 Bedienungsanleitung

ClearSpan

ClearSpan Cedar 12' Wide End Frame Kit with Dutch Door Bedienungsanleitung

ClearSpan

ClearSpan CL108552 Bedienungsanleitung

ClearSpan

ClearSpan 500 Cold Frame Series Bedienungsanleitung

ClearSpan

ClearSpan PB00556R3S Bedienungsanleitung

ClearSpan

ClearSpan PB00250R4 Bedienungsanleitung

Beliebte Gewächshaus-Bausatz Handbücher anderer Marken

ACD PRESTIGE

ACD PRESTIGE MR3 H Bedienungsanleitung

Vitavia

Vitavia VA0040-TRP Bedienungsanleitung

VegTrug

VegTrug Nursery Bedienungsanleitung

Riverstone Networks

Riverstone Networks Monticello 041315V Bedienungsanleitung

STC

STC Easy Grow 6x12 Greenhouse Bedienungsanleitung

CLIMA POD

CLIMA POD Spirit V7 Series Bedienungsanleitung

Vitavia

Vitavia GAIA JUMBO Bedienungsanleitung

Palram

Palram Harmony 6'x4' Bedienungsanleitung

Sproutwell

Sproutwell GRANGE - 5 Bedienungsanleitung

ACD

ACD Piccolo 03 Bedienungsanleitung

Growhouse

Growhouse Lean To 6 x 8 Bedienungsanleitung

Riverstone Networks

Riverstone Networks Grower's 181010V Bedienungsanleitung

GrowSpan

GrowSpan 500 Series Bedienungsanleitung

Robinsons

Robinsons 5ft Wide LEAN-TO Bedienungsanleitung

Botanica

Botanica E Bedienungsanleitung

PNI

PNI SP6000 Bedienungsanleitung

Hortus

Hortus 211-203 Programmierhandbuch

Robinsons

Robinsons 6' Lean-To Bedienungsanleitung