Clifford AvantGuard II Bedienungsanleitung

Owner'sManual

World-ClassAutoSecurity TM

AvantGuard

Table of Contents

EXTREMELY IMPORTANT NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

How to Operate the Premier™ Remote Control . . . . . . . . . . . . . . . . . . 3

How to Disarm the System with the Remote Control . . . . . . . . . . . . . . . 3

How to Arm the System with the Remote Control . . . . . . . . . . . . . . . . 4

How to Panic the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

How to Remotely Control Accessories and/or Other Clifford Systems . . . . . 4

Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

How to Enable Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

How to Exit Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

AutoLock™ and AutoUnLock™ . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

What to Do If You Inadvertently Cause the Alarm to Sound . . . . . . . . . . . . 5

FACT™—False Alarm Control and Test . . . . . . . . . . . . . . . . . . . . . . . 5

Smart AntiScan™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Smart AutoArming™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Smart AutoDiagnostics™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Malfunction AutoBypass™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Prior Intrusion Attempt Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Multicolor LED Status Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

“Chirp” Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SmartSiren™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

What Do the Chirps and Flashes Mean? . . . . . . . . . . . . . . . . . . . . . . 8

SmartPowerUp™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Remote Engine Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

How to Remotely Start the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Driving the Vehicle After Remote Starting . . . . . . . . . . . . . . . . . . . . . . 9

The AutoStart™ Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

How to Engage AutoStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Remote Starter Do’s and Don’ts . . . . . . . . . . . . . . . . . . . . . . . . . . 10

How to Program Your AvantGuard II . . . . . . . . . . . . . . . . . . . . . . . . 11

How to Change Siren Duration . . . . . . . . . . . . . . . . . . . . . . . . . 11

How to Set Your Own Personalized Siren Sound . . . . . . . . . . . . . . . . 12

How to Adjust Sensitivity of the Optional OmniSensor . . . . . . . . . . . . . 13

How to Enable/Disable FACT . . . . . . . . . . . . . . . . . . . . . . . . . . 13

How to Enable/Disable AutoLock and AutoUnLock . . . . . . . . . . . . . . 14

How to Enable/Disable Smart AutoArming . . . . . . . . . . . . . . . . . . 14

How to Set the Smart AutoArming Entry Delay . . . . . . . . . . . . . . . . . 15

How to Add a New Remote Control . . . . . . . . . . . . . . . . . . . . . . 15

How to Delete the Code of a Lost or Stolen Remote Control . . . . . . . . . 16

Quick Programming Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

EXTREMELY IMPORTANT NOTICE

If the AvantGuard II’s control unit is removed from the vehicle for any reason, the

supplied RED jumper wire MUST BE CONNECTED to pins #8 and #11 of the

PIGTAIL connector.WARNING

1. TheAvantGuardIIisdesignedtobeusedonlyonagasoline-powered,fuel-injected

vehicle with automatic transmission. If attempts are made to install the remote

starter on a vehicle with a manual transmission, the artificial intelligence of the

system will detect this and will render the system inoperative. The control unit

willnotrespondtoattemptsatreactivationandwillhavetobereturnedtoClifford

Electronics. There is a charge of $50 for this service.

2. If the vehicle is to be serviced, remove the 5-amp fuse from its holder connected

to the positive (+) terminal of the vehicle battery (leave the 30-amp fuse in place).

Whenservicingiscomplete,TURNTHEIGNITIONKEYON,thenfirmlyreinsert

the 5-amp fuse.

Always exercise caution and common sense when using the remote starter:

NEVER start the vehicle in an enclosed area without sufficient ventilation.

NEVER allow children access to the remote control.

NOTE: You must shift the transmission into DRIVE for at least 3 seconds if the

ignition has been turned on and off more then 10 consecutive times and/or

the engine has been remotely started more than 10 consecutive times.

Failure to do so will render the system inoperative.

Congratulations on your purchase of the Clifford AvantGuard II, the

world’s most advanced vehicle security and remote engine starter

system.TheAvantGuardIImasterfullycombinesthestate-of-the-art

in vehicle security with amazingly innovative remote engine starting fea-

tures to achieve the pinnacle in driver convenience, comfort and safety. Yet

despite the expansive wealth of stunning features, you will find the

AvantGuardIItobewonderfullyuser-friendly.CustomizingtheAvantGuard

II to meet your exact needs is as easy as a few flicks of a switch, but even

thatsimpleeffortisnotrequired.ThesystemcomesfromCliffordElectronics

completelypresetandpreprogrammed,socommandingitisnomoredifficult

than pressing a button on the Premier™ remote control.

How to Operate the Premier™ 4x8 Remote Control

The Premier 4-button/8-channel, 4-billion code remote control provides incredibly

high digital code security to give you the ultimate in protection against professional

thieves using digital code scanners. Even a thief equipped with the most sophisti-

cated scanning device would need more then 19 years to decipher your system’s

security code.

What’s more, the remote control’s four buttons and eight different channels enables

you to remotely command any aspect of the AvantGuard II and its optional accesso-

ries. It is also capable of controlling AvantGuard II, IntelliGuard Series and Clifford

Nova, Delta IV and Ace II systems and accessories on other vehicles you own — up

to a total of eight with just one remote control.

With the remote control microswitch in the up position, buttons I-IV transmit

channels 1-4; in the down position, the same buttons transmit channels 5-8.

The remote control has a typical range of 300 feet. Certain factors—such as terrain,

physical obstructions, weather conditions or a weak remote control battery—may

effect the range. Button I (channel 1) will arm/disarm and simultaneously lock/un-

lock the car doors for you and your passengers. If you press button I (channel 1) for

3 seconds, it will sound the siren and flash the parking and interior lights (see How

to Panic the System, page 4). Button II (channel 2) will start or shut down the engine

and all preset accessories. Optionally, channels 3-8 can individually command

SmartWindows II, a remote trunk release, electric garage doors and/or Clifford

systems on your other vehicles. Ask your Authorized Clifford Dealer about these

options.

How to Disarm the System with the Remote Control

With the remote control microswitch in the up position, button I (channel 1) will

always arm or disarm the system:

1. Press remote control button I/channel 1.

2. Simultaneously, several actions will take place to confirm remote disarming:

•The siren will chirp once, providing audible confirmation from a distance. (If

you prefer, you can turn off the chirp acknowledgements (see page 7 for details).

•The parking lights will flash once, providing visual confirmation from a

distance.

•The car doors will automatically unlock for you and your passengers.

•For your safety and convenience, the interior courtesy light will turn on if the

engine is off, allowing you, at night, to check inside the car before entering.

•The MultiColor LED inside the car will turn off. (The LED will begins flashing

green when the interior light turns off, indicating you have 30 seconds to enter

the vehicle or it will automatically re-arm; see Smart AutoArming on page 6.)

3. Release button I as soon as you observe any of the above actions.

4. Enter the vehicle. For your convenience, the interior light will remain on until

you start the engine, or for 30 seconds, whichever occurs first.

How to Arm the System with the Remote Control

1. Press remote control button I/channel 1.

2. Simultaneously, several actions will take place to confirm remote disarming:

•The siren will chirp twice providing audible confirmation from a distance. (If

you prefer, you can turn off the chirp acknowledgements (see page 7 for details).

•The parking lights will flash twice, providing visual confirmation from a

distance.

•The car doors will automatically lock.

•The windows/sunroof will close automatically if your vehicle is equipped with

the optional SmartWindows II accessory.

•The Multicolor LED inside the car will begin flashing red.

3. Release button I as soon as you observe any of the above actions.

How to Panic the System

As an added safety measure, AvantGuard II is designed to respond if you ever face

harassment and are within transmittal range of the vehicle. Simply press button I

continuously for 3 seconds. The siren will sound, the parking lights will flash and

the interior dome light will flash, calling attention from passersby.

How to Remotely Control Accessories and/or Other Clifford Systems

To activate accessories such as SmartWindows II, a remote trunk release, one or

more Garage Door Programmable Receiver(s) and/or your other vehicle(s) equipped

with AvantGuard II, IntelliGuard or Clifford Nova, Delta IV or Ace II system(s),

simply press the assigned button.

For example, with the requisite optional accessories, your Premier 4x8 remote

control can separately and independently command all of the following functions:

With the remote control microswitch in the up position:

•Button I (channel 1) will arm, disarm and panic your security system.

•Button II (channel 2) will remotely start or shut down the engine.

•Button III (channel 3) will remotely pop the trunk.

•Button IV (channel 4) will remotely roll-down or vent the power windows.

With the remote control microswitch in the down position:

•Button I (channel 5) will activate your electric garage door.

•Button II (channel 6) will arm, disarm and panic an AvantGuard II (or other

Clifford vehicle security system) on your second car.

•Button III (channel 7) will remotely start or shut down the engine on your second

car.

•Button IV (channel 8) will remotely pop the trunk on your second car.

You may reassign the buttons/channels any time you wish (see page 15 for details).

Valet Mode

Whenever your vehicle is to be serviced, washed or valet parked, you must use the

valet mode to disarm the system and override its Smart AutoArming feature.

How to Enable Valet Mode

1. Insert your key and turn the ignition to the “ON” position.

2. Flip the valet/program switch to its latched (non-momen-

tary) position.

3. The LED will light in red and remain on, confirming the system is in valet mode.

4. You may now turn the ignition off and remove your key.

NOTE: If you temporarily lose the use of your remote control, you can disarm

the system by enabling valet mode.

How to Exit Valet Mode

1. Insert your key and turn the ignition to the “ON” position.

2. Flip the valet/program switch to its center position.

3. The LED will turn off, confirming the system is in normal operating mode.

NOTE: In valet mode, the remote control will still lock/unlock the doors, start

the engine and command options (e.g., remote trunk release, etc.).

AutoLock™ and AutoUnLock™

For your safety, the system automatically locks your car doors 5 seconds after you

shift the transmission into Drive. Conversely, the doors automatically unlock after

you turn the ignition off. If you prefer, you may turn this feature off (see page 14).

What to Do If You Inadvertently Cause the Alarm to Sound

If you unintentionally alarm the system, simply press button I (channel 1) on your

remote control or enable the valet mode.

FACT™—False Alarm Control and Test

WiththeuniqueFACTfeature,you’ll never experience repeated false alarms. If your

sirengoesoff,donotremotelydisarmthesystem;allowittorunforthefullsirenduration

(30 seconds or whatever duration you programmed). The system automatically checks

foranotheractivatedtriggerbeforesoundingthesirenasecondtime.Ifthesirensounds

again, you will know for sure that someone is tampering with your vehicle.

Smart AntiScan™

Thievescandisarmrun-of-the-millcaralarmswitha“scanner”thatrapidlytransmits

oneremotecontrolcodeafteranother.Yeteventhemostsophisticatedscannerwould

need more than 19 years to decipher Premier remote control’s 4.3-billion-codes.

Evenifyouaddabasic(16,000-code)remote,SmartAntiScanwilldetectanyscanner,

block the codes it generates, sound the siren and flash the parking lights.

Smart AutoArming™

If you forget to arm your system with the remote control, it will arm itself automat-

ically 30 seconds after the vehicle doors are closed. (The Multicolor LED will blink

greenfor visualconfirmationof the30-secondSmartAutoArmingcountdown).Ifyou

re-open any door(s) within the 30-second countdown, the AutoArming process will

restart from the beginning once all doors are closed.

Whenever the system AutoArms, an entry delay (factory preset to 15 seconds) will

be in effect when you return. This allows you to disarm the system before the alarm

sounds if you lose the use of your remote control. To disarm without the remote

control after the system has AutoArmed, simply enter the vehicle and turn on the

ignition switch within 15 seconds.You may set the entry delay to any interval

between 1 and 59 seconds. In fact, if you wish, you may eliminate the entry delay

and the Smart AutoArming feature altogether (see page 15).

NOTE: When the system arms automatically, the doors will not lock. This will

prevent you from being locked out of the car while your keys remain inside.

NOTE: To prevent AutoArming when fueling the vehicle, either enable the

valet mode (see page 5) or leave one of the doors open.

Smart AutoDiagnostics™

The AvantGuard II will automatically and instantly perform a comprehensive test

of all system triggers and sensors every time you arm the system. In the rare event

that a trigger malfunctions, the system will alert you of the problem by immedi-

ately issuing four chirps and four flashes of the parking lights instead of the

usual twochirps and twoflashes. If oneof the sensors malfunctions,the system will

issue the usual 2 chirps and 2 flashes, then 5 seconds later the system will issue

four chirps and four flashes.

Smart AutoDiagnostics will even identify the specific defect to reduce trouble-shooting

time. To identify a defect, disarm the system. The Multicolor LED will blink in red

1-4 times, pause for one second, then repeat the cycle four more times. Count the

number of blinks in one of the 5 cycles and use the table below to identify the defect.

LED Indication Malfunction

1 blink Magnetic Resonance Sensor

2 blinks Optional Proximity Sensor and/or IntelliSensor 3-D

4 blinks Hood or Trunk Trigger

Malfunction AutoBypass™

Once Smart AutoDiagnostics identifies a malfunctioning trigger or sensor it will

instantly activate the Malfunction AutoBypass feature, which will automatically

override any malfunction and arm all other triggers and sensors. Your vehicle will

never be without some measure of protection.

Prior Intrusion Attempt Alert

If the alarm sounded while you were away, when you remotely disarm the system

will issue three chirps and three flashes of the parking lights. You’ll note that the

Multicolor LED will blink in red 1-7 times, pause for one second then repeat the

cycle four more time. Count the number of red blinks in any one of the 5 cycles and

use the table below to identify the trigger or sensor that detected the attempt.

LED Indication Tripped Trigger or Sensor

1 blink Magnetic Resonance Sensor

2 blinks Optional Proximity Sensor and/or IntelliSensor 3-D

4 blinks Hood or Trunk Trigger

7 blinks Scan Attempt (see Smart AntiScan on page 5)

Multicolor LED Status Indicator

The Multicolor LED Status Indicator confirms system status:

LED Indication System Status

Off System is disarmed, you may enter the vehicle

On (red) Valet or programming mode

Flashing (red) System is armed and protecting your vehicle

Flashing (green) 30-second AutoArming Countdown

“Chirp” Muting

If and when you desire, you may silence the chirp confirmations, allowing for only

silent, parking light arm/disarm confirmation (of course, if an intrusion attempt

occurs, the SmartSiren will sound). You have two choices:

•You may disable the chirps until you wish to enable the chirps again.

•Disable the chirps for only one arm and disarm cycle.

For long-term chirp muting/restoration, use the following procedure:

1. Turn the ignition key to the “ON” position.

2. Within 10 seconds, press and hold the valet/program switch to its momentary

position until you hear a siren chirp, then release. The LED will light in red and

stay lit, confirming that the system is in program mode.

3. Tap the valet/chirp-mute switch to its momentary position 2 times.

4. Flip the switch to its latched position, then back to center. You will hear 2

confirmation chirps.

5. Tap the switch to its momentary position 4 times.

6. Flip the switch to its latched position, then back to center. You will hear 4

confirmation chirps.

a. To turn the chirps off: Tap the switch to its momentary position.

b. Toturnthechirpson:Flicktheswitchtoitslatchedposition,thenbacktocenter.

c. You will hear 3 chirps to confirm chirp muting or restoration.

7. Turn the ignition off. You will hear 3 chirps to confirm exiting of program mode.

One-Cycle Chirp Muting: This is particularly useful when parking in a quiet

residential area. Just rapidly turn the ignition on and off. When you next arm, and

laterdisarm, there will beno chirps. After that,the chirps are automatically restored.

SmartSiren™

TheSmartSirennotonlysounds when an intrusion attempt is detected, but it allows

you to program your own siren duration from 1 second to 5 minutes (for your

convenience, siren duration is factory preset to 30 seconds). What’s more, when you

hear your siren you will know that it is your car since you can program SmartSiren

to sound your own personalized sound pattern. See pages 10-11 for details.

Even if a door is left open in the wake of an intrusion, the SmartSiren will sound no

more than five cycles of the siren duration, ensuring against excessive battery drain

or the vehicle being towed due to noise pollution. It will then automatically override

the door trigger and re-arm, providing your vehicle with uninterrupted protection.

What Do the Chirps and Flashes Mean?

When you remotely arm or disarm the system, the siren will chirp and the parking

lights will flash. The following table explains the meaning of the chirp/flash signals:

Chirp/Flash Indication System Status

1 chirp/1 flash System has been disarmed by remote.

2 chirps/2 flashes System has been armed by remote.

3 chirps/3 flashes System has been disarmed and the alarm sounded while

you were away (refer to the Prior Intrusion Attempt Alert

section on page 7).

4 chirps/4 flashes

immediately upon

remote arming

System has been armed by remote, but there is a trigger

malfunction (refer to the Smart AutoDiagnostics section on

page6).Thesystemisarmedandthetrigger/sensordefect

has been automatically bypassed.

4 chirps/4 flashes

5 sec. after remote

arming

System has been armed by remote, but one of the sensors

is active (refer to the Smart AutoDiagnostics section on

page6).Thesystemisarmedandthesensorinputhasbeen

automatically bypassed.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clifford Autoalarmanlage Handbücher

Clifford

Clifford 5806X Bedienungsanleitung

Clifford

Clifford AvantGuard 3 Bedienungsanleitung

Clifford

Clifford IntelliGuard 8000 Bedienungsanleitung

Clifford

Clifford Model RSX3.5 Bedienungsanleitung

Clifford

Clifford concept 50x Bedienungsanleitung

Clifford

Clifford Concept 100 Bedienungsanleitung

Clifford

Clifford intelliguard 800 Bedienungsanleitung

Clifford

Clifford AVANTGUARD 5 Bedienungsanleitung

Clifford

Clifford G5 11CX 562C Bedienungsanleitung

Clifford

Clifford Smart Remote Starter Bedienungsanleitung

Clifford

Clifford Eagle II Bedienungsanleitung

Clifford

Clifford Smart Siren 4 Handbuch

Clifford

Clifford Ultramax XL2500 Bedienungsanleitung

Clifford

Clifford Matrix 1 Bedienungsanleitung

Clifford

Clifford Arrow 5.1 Bedienungsanleitung

Clifford

Clifford 500 Bedienungsanleitung

Clifford

Clifford 4606X Bedienungsanleitung

Clifford

Clifford Delta IV Bedienungsanleitung

Clifford

Clifford AVANTGUARD 5 Bedienungsanleitung

Clifford

Clifford cyber Arrow 3 Bedienungsanleitung

Clifford

Clifford Matrix 2.2X Bedienungsanleitung

Clifford

Clifford ACE 2000 Bedienungsanleitung

Clifford

Clifford Prime Level Three Bedienungsanleitung

Clifford

Clifford AvantGuard 4 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung

Megalarm

Megalarm MEGA 3600 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung