Clifford SE 2020 Special Edition Bedienungsanleitung

Using Your SE 2O2OXSecurity System

The 2-Button/3-Channel Remote Controls

Your two 2-button/3-channel remote controls are miniature radio transmitters that

send three distinct digital codes up to 150 feet. Obstructions, interference or a weak

battery will reduce the range. The remote control is the key to your security system.

Use it to arm or disarm the system, lock or unlock the doors, activate its panic

feature or control options such as a remote trunk release.

TO ARM

THE SYSTEM . . . . . . . Press button I once. You will hear two chirps and the parking

lights will flash twice. The dashboard LED will flash repeat-

edly and the car doors will automatically lock. Any attempt to

break into the vehicle will immediately disable the starter,

sound the siren and flash the parking lights.

TO DISARM

THE SYSTEM . . . . . . . Press button I again. One chirp and one flash of the parking

lights will confirm disarming. In addition, the car doors will

automatically unlock.

TO SILENTLY

ARM OR DISARM

THE SYSTEM . . . . . . .

Simultaneously press buttons I+II. The system will arm or dis-

arm with all the indications noted above except the chirp ac-

knowledgments.

TO ACTIVATE

THE PANIC

FEATURE . . . . . . . . . .

Press button I for 3 seconds. The lights will flash repeatedly

and the siren will blare for 30 or 60 seconds (user-selectable),

or until you press button I again to turn it off.

TO ACTIVATE AN

OPTION . . . . . . . . . . Button II controls an optional accessory such as a remote

trunk release, SmartWindows II, the headlight activation fea-

ture of NightVision, the remote controlled voice-silencing fea-

ture of Sense & Tell, IntelliStart remote engine starter, your

electric garage door or a Clifford system on your second vehi-

cle. Ask your dealer about these options.

What to Do If You Inadvertently Cause the Alarm to Sound

If you unintentionally alarm the system, just press button I on your remote control

or enable valet mode (see page 2) to disarm the system.

Enhanced AutoArming™

If you forget to remotely arm SE 2020X, it will arm itself automatically 30 sec-

onds after the vehicle doors are closed. If you re-open any door(s) within the 30-sec-

ond countdown, AutoArming will restart from the beginning once all doors are

closed. This ensures you’ll never accidentally leave your vehicle unprotected. SE

2020X includes all these Enhanced AutoArming features:

AutoArming Enable/Disable: If you prefer, you may, at any time, deactivate or

reactivate AutoArming. To do, see How to Set User-Selectable Features on

pages 6-7.

Visual Acknowledgment: Five seconds after you exit the vehicle and close all

the doors, the parking lights will flash twice to confirm that the AutoArming

countdown is progressing. Then, 25 seconds later, the system will AutoArm.

AutoArm & Lock: To ensure you can’t accidentally lock your keys inside the

car, your SE 2020X is factory-set not to lock the doors upon AutoArming. To

change this setting, see How to Set User-Selectable Features on pages 6-7.

NOTE: To prevent AutoArming of the system when fueling the vehicle, either

enable valet mode or leave one of the doors open (the system AutoArms 30

seconds after all doors are closed).

Valet Mode

Whenever your car is to be serviced, washed or valet parked, you must use the

valet mode in order to prevent unintentional activation of the alarm.

How to Enable Valet Mode

1. Insert your key and turn the ignition to the ON position.

2. Flip the valet/program switch. The LED inside your vehicle will turn on,

confirming the system is in valet mode.

3. You may now turn the ignition off and remove your key.

NOTE: If you temporarily lose the use of your remote control, you can disarm

the system by enabling valet mode.

NOTE:Eveninvaletmode,youmaystillusetheremotecontroltolockorunlock

the doors and/or activate a remote controlled accessory.

How to Exit Valet Mode

1. Insert your key and turn the ignition to the ON position.

2. Flip the valet/program switch. The LED inside your vehicle will turn off,

confirming the system is in normal operating mode.

Triple-Mode Chirp Silencing

If and when you desire, you may silence the chirp confirmations, allowing for only

silent, parking light arm/disarm confirmation (of course, if an intrusion attempt oc-

curs, the siren will sound its 125dB wail). You have three chirp muting choices:

Long-Term Chirp Silencing: You may disable the chirps until you wish to restore

them. To do so, see How to Set User-Selectable Features on pages 6-7.

One-Cycle Chirp Muting: You may disable the chirps for only one arm-and-dis-

arm cycle, after which the chirps are automatically restored. To do so, simply

turn the vehicle’s ignition switch “ON” and “OFF” rapidly. When you next

arm, and later disarm, the chirps will be silenced.

On-the-Go Remote Chirp Muting: You may silently arm or disarm the alarm

with the remote control on-the-go and without any prior preparation by simul-

taneously pressing buttons I and II of the remote control.

What Do the Chirps and Flashes Mean?

When you remotely arm or disarm the system, the siren will chirp (unless you

have the chirps silenced) and the parking lights will flash:

Chirps/Flashes System Status

1 chirp/1 flash System has been disarmed by remote.

2 chirps/2 flashes System has been armed by remote.

3 chirps/3 flashes System has been disarmed by remote, but the alarm sounded while you were away.

4 chirps/4 flashesimmediately

upon remote arming System has been armed by remote, but the hood and/or trunk trigger is open.

The system is armed and the hood/trunk trigger is automatically bypassed.

4 chirps/4 flashes5 seconds af-

ter remote arming System has been armed by remote, but the sensor is active.

The system is armed and the sensor input is automatically bypassed.

Smart AutoTesting™

In the rare event of a trigger or sensor malfunction, your SE 2020X will alert you

of the problem. Arm the alarm with the remote control. If the system detects a

faulty trigger, the system will issue four chirps and four parking light flashes in-

stead of the usual 2 chirps/2 flashes. If a sensor malfunction is detected, the sys-

tem will issue the usual 2 chirps and 2 flashes, then, 5 seconds later, it will emit 4

chirps and 4 flashes.

NOTE: Since this is a warning indication, you will hear the 4-chirp signal even if

you are using the chirp silencing feature.

Malfunction AutoBypass™

Once the Smart AutoTesting feature identifies and records a trigger or sensor mal-

function, your SE 2020X will instantly override the defect and arm all other points.

Your vehicle will never be without some measure of protection. You should, as

soon as possible, take your vehicle to your Authorized SE Dealer for servicing.

TotalRecall™ of Last Activated Trigger or Sensor

The SE 2020X’s non-volatile memory automatically stores the last trigger or sen-

sor activated, thereby providing an invaluable diagnostics means. To recall the

identity of the last activated trigger or sensor, use the following procedure:

1. Disarm your SE 2020X with button I on the remote control.

2. With the ignition OFF, flick the valet/programming switch.

3. Press button I until you hear 2 chirps, release, then press button I again

until you hear 1 chirp. The LED status indicator will blink 1 - 3 times,

pause, then repeat the blink cycle four more times. Count the number of

blinks per cycle and refer to the table below:

LED Blinks System Component that Malfunctioned

1 blink Magnetic Resonance Sensor or optional sensor(s)

2 blinks Door trigger

3 blinks Hood or trunk trigger

Your SE 2020X will hold this information in its non-volatile memory indefinitely

or until there is a subsequent activation.

AutoLock™ and AutoUnLock™

For additional safety, AutoLock automatically locks all of your vehicle’s doors

when you start the engine. Conversely, AutoUnLock unlocks the doors for you

and your passengers when you turn the ignition off. To deactivate (or reactivate)

this feature, see How to Set User-Selectable Features on pages 6-7.

FACT™ — False Alarm Control and Test

With FACT, you’ll never experience repeated false alarms. If your siren goes off,

DO NOT disarm the system; allow it to run for the full 30-second or 60-second

(user-selectable) siren duration. Your SE 2020X automatically checks for another

activated trigger before sounding the siren a second time. Should the siren sound

again, you will know for sure that someone is tampering with your vehicle.

Tampering Warning™

Normally, SE 2020X immediately sounds its siren at the first inkling of an intru-

sion attempt. However, you may set the system to issue a rapid five-chirp warning

whenever SE 2020X detects tampering to the exterior of your vehicle. If there is

any further tampering within the next 30 seconds, or if a door, the hood or trunk is

opened at any time, SE 2020X will sound a continuous 125dB siren blast. To se-

lect the mode of your choice, see How to Set User-Selectable Features on pages 6-7.

NOTE:TurningontheTamperingWarningfeatureoverridesFACT,andvice-versa.

Smart Prior Intrusion Attempt Alert

If the alarm was activated while you were away, when you disarm with the remote

control your SE 2020X will issue three chirps and three parking light flashes in-

stead of the usual one chirp/one flash.

NOTE: Since this is a warning indication, you will hear the 3-chirp signal even if

you are using the chirp muting feature.

When you enter your vehicle, the LED status indicator will be blinking 1-3 times,

pause, then repeat the blink cycle four more times to indicate the trigger/sensor

that detected the intrusion attempt. Count the number of blinks per cycle and refer

to the table below:

LED Blinks Trigger/Sensor that Detected the Intrusion Attempt

1 blink Magnetic Resonance Sensor or optional sensor(s)

2 blinks Door trigger

3 blinks Hood or trunk trigger

LED Status Indicator

The LED status indicator on your vehicle’s dashboard or console is used to com-

municate the operational condition of your system:

LED Indication System Status

Off System is disarmed, you may enter the vehicle

On Valet or programming mode

Flashing System is armed and protecting your vehicle

Blinking in cycles

of 1-3 blinks Smart Prior Intrusion Attempt Alert identification of a tripped trigger or sensor (see

above), or TotalRecall of a trigger or sensor malfunction (see page 4).

How to Set User-Selectable Features

To change the setting of any one or more of the User-Selectable Features, simply

select the feature you wish to change from the following chart, perform the steps

below, flick the valet switch the number of times indicated, then turn off the ignition.

To change the setting of a user-selectable feature:

1. Select the feature you wish to set from the chart on the next page.

2. Turn the ignition key to the ON position.

3. Within 10 seconds, flick the valet/programming switch back and forth,

counting each confirmation chirp. Stop when you reach the number of

chirps indicated for the feature you wish to set.

4. If noted, perform the “Supplemental action.”

5. Wait for the “Completion confirmation,” then turn the ignition off.

6. Repeat steps 1-5 for any other features you wish to set.

Adding New Remote Control(s)

Your SE 2020X can function with as many as four different Clifford remote con-

trols, regardless of their types, specific codes or number of channels. Adding one

or more additional remote controls is simple, just use the procedure noted in the

How to Set User-Selectable Features on this and the following page.

NOTE: You can obtain additional remote controls from any Authorized Clifford

Dealer, or call our Customer Service Department toll-free at (800) 824-3208.

How to Delete the Code of a Lost or Stolen Remote Control

To delete the code of a lost or stolen remote control from the system memory, sim-

ply program buttons I, II and the I+II combination of your current remote control

into the system 4 times (see Adding New Remote Control(s) above). If you have

two remotes, program each twice. If using three or more remote controls, program

all of them so that the total adds up to 4.

Example

To change the AutoArming feature from its factory setting of on to off:

•Turn the ignition key to the ON position.

•Immediately flick the valet/program switch back and forth while counting the

number of confirmation chirps.

•When the 4th chirp sounds, wait 3 seconds. The system will sound one more

chirp to confirm that the siren duration setting has been changed.

•Turn the ignition off.

31-058B/80-058/2/20XOM 4/93

Feature Factory

setting

# of

flicks &

chirps

Secondary

action

Program

completion

confirmation Result

AutoArming ON 4—1 chirp 3

seconds after

last step

Change state from

ON to OFF or vice-versa

AutoArm

& Lock OFF 5—1 chirp 3

seconds after

last step

Change state from

ON to OFF or vice-versa

Arm/Disarm

Chirp

Confirmation ON 6—1 chirp 3

seconds after

last step

Change state from

ON to OFF or vice-versa

AutoLock/

AutoUnLock ON 9—1 chirp 3

seconds after

last step

Change state from

ON to OFF or vice-versa

Siren

Duration 30 sec. 10 —1 chirp 3

seconds after

last step

Change duration from 30

to 60 seconds or vice-versa

Tampering

Warning OFF 11 —1 chirp 3

seconds after

last step

Change state from

OFF to ON or vice-versa

FACT —

False Alarm

Control and

Test ON 12 —1 chirp 3

seconds after

last step

Change state from

OFF to ON or vice-versa

Add a New

Remote to

Channel 1

(arm/disarm) —13 Press

remote control button I1 chirp Button I/channel 1 code of

new remote control has

been memorized

Add a New

Remote to

Channel 2

(optional re-

mote

accessory)

—14 Press

remote control button II 2 chirps Button II/channel 2 code of

new remote control

has been memorized

Add a New

Remote to

Channel 3 (si-

lent arm/dis-

arm)

—15 Simultaneously press

remote control buttons I+II 3 chirps Button I+II/channel 3 code

of new remote control

has been memorized

Andere Handbücher für SE 2020 Special Edition

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clifford Autoalarmanlage Handbücher

Clifford

Clifford Prime Level Three Security Upgrade Package Bedienungsanleitung

Clifford

Clifford SmartWindows 4 Bedienungsanleitung

Clifford

Clifford 590.4X Bedienungsanleitung

Clifford

Clifford 4806X Bedienungsanleitung

Clifford

Clifford concept 50 Bedienungsanleitung

Clifford

Clifford 20.5X Bedienungsanleitung

Clifford

Clifford intelliguard 800 Bedienungsanleitung

Clifford

Clifford ARROW 5 Bedienungsanleitung

Clifford

Clifford Eagle II Bedienungsanleitung

Clifford

Clifford 5706X Bedienungsanleitung

Clifford

Clifford 4806X Bedienungsanleitung

Clifford

Clifford Prime Level 1 Bedienungsanleitung

Clifford

Clifford Arrow 5.1 Bedienungsanleitung

Clifford

Clifford intelliguard 700 Bedienungsanleitung

Clifford

Clifford Arrow II Bedienungsanleitung

Clifford

Clifford Auto Immobilizer Bedienungsanleitung

Clifford

Clifford Cyber 4 Bedienungsanleitung

Clifford

Clifford Nova III Bedienungsanleitung

Clifford

Clifford 5806X Bedienungsanleitung

Clifford

Clifford CallGuard Bedienungsanleitung

Clifford

Clifford Novell Bedienungsanleitung

Clifford

Clifford 3105X Bedienungsanleitung

Clifford

Clifford Delta IV Bedienungsanleitung

Clifford

Clifford System II Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung

Megalarm

Megalarm MEGA 3600 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung