Clifford Wireless Immobilizer XL 500 Bedienungsanleitung

ThekeychainremotecontrolsarethekeystoyourXL5OOsystem.Ifyouneed

additionalremotecontrolsforotherdriversofthevehicle,seeyour

AuthorizedCliffordDealerorcalltheCliffordCustomerServiceDepartment

toll-freeat(8OO)824-32O8.

World-ClassAutoSecurity TM

Standard Features of the XL500

✔Lifetime Warranty— For as long as you own the vehicle (see warranty card for details).

✔FACT™ — False Alarm Control and Test — Eliminates recurring false alarms.

✔A Pair of 2-Button/3-Channel Remote Controls — Fingertip control from 100’ away.

✔Patented Remote Control Code Learning and MultiRemote™ Recognition — Add or

delete, with just a few flicks of a switch, up to 2 different Clifford remote controls.

✔Multiple-Car Control — Allows you to command, with the same remote control, a

Clifford vehicle security system on your second vehicle.

✔AntiScan™ — Blocks electronic scanners from disarming the alarm.

✔Remote Controlled Chirp Muting — Lets you arm or disarm silently anytime you

wish (the parking lights provide visual confirmation).

✔Remote Door Lock/Unlock Outputs — Automatically locks/unlocks your vehicle’s

doors when you remotely arm/disarm your XL500 (some vehicles require optional

relays).

✔Parking Light Flasher Output— Visually confirms alarm status from a distance (most

vehicles require an optional relay).

✔Patented AutoTesting™ — Automatically tests for any trigger/sensor malfunction.

✔Malfunction AutoBypass™ — Bypasses any malfunction and arms all other points.

✔Patented Prior Intrusion Attempt Alert — Identifies whether a trigger or a sensor was

activated during an attempted intrusion while you where away.

✔Advanced CMOS Microprocessor — Commands and monitors system functions

more than 10,000 times per second, yet draws less power than your car’s clock.

✔Full-Time Remote Panic — For your safety, you can remotely activate the siren and

flashing parking lights from inside or outside the vehicle, even while driving.

✔High-Output Siren — Very loud alarm sound with automatic noise abatement to

ensure against excessive battery drain or towing of the vehicle due to noise

pollution.

✔Smart AutoArming™ — Arms itself “passively” if you forget.

AutoArming Enable/Disable — Enable or disable AutoArming any time.

User-Selectable AutoArm & Lock — Select whether the doors lock upon AutoArming.

✔Fault-Proof Starter Interrupt Output— With the addition of an optional relay,

prevents an intruder from starting the engine.

✔Magnetic Resonance Sensor™ — Detects intrusion-related vibrations and impacts.

✔High-Luminescence LED Status Indicator — Adds visual deterrence and provides

alarm status confirmation.

✔Hood/Trunk Trigger Input — For full perimeter protection of the engine

compartment and trunk contents (may require optional pin switches and wiring).

✔User-Friendly Programming — A few flicks of a switch is all it takes.

✔Secured Valet Mode — Permits vehicle servicing and valet parking without

relinquishing your remote control.

Your 2-button/3-channel remote controls

The 3-button/3-channel remote control is a miniature radio transmitter powered by a

tiny 12-volt battery. Range is up to 100 feet. Obstructions, electrical interference,

weather conditions or a weak battery will reduce the range. Your 2-button/3-channel

remote is the key to your XL500 system. You will use it to arm and disarm the

system, lock and unlock the doors, activate the panic feature and control options

such as a remote trunk release. Additional remote controls and remote control

batteries are available from any Authorized Clifford Dealer, or call our 24-hour

Customer Service Department toll-free at (800) 824-3208.

TO ARM

THE SYSTEM . . . . . . . Press button I once. You will hear two chirps and the parking

lights will flash twice (most vehicles require an optional

parking light relay). The dashboard LED will flash repeatedly

and the car doors will automatically lock (some vehicles

require optional relays). Any attempt to break into the vehicle

will sound the siren, optionally flash the parking lights and, if

you have this option, electronically disable the starter.

TO DISARM

THE SYSTEM . . . . . . . Press button I again. One chirp and, optionally, one flash of

the parking lights, will confirm disarming. In addition, the car

doors will unlock.

TO SILENTLY

ARM OR DISARM. . . Simultaneously press buttons I+II. The system will arm or

disarm with all the indications noted above except the chirps.

TO ACTIVATE

THE PANIC

FEATURE . . . . . . . . . .

Press button I for 3 seconds. The parking lights will flash

repeatedly (again, most vehicles require an optional parking

light relay) and the siren will blare for 30 seconds, or until you

press button I again to turn it off.

TO ACTIVATE

AN OPTION . . . . . . . Button II may activate a remote controlled option, such as a

remote trunk release, IntelliStart remote engine starter,

NightVision’s remote headlight activation feature, the venting

and rolldown features of SmartWindows II, etc.

AntiScan™

Car thieves use electronic scanners that rapidly transmit one remote control code after

another to defeat ordinary car alarms. AntiScan prevents scanners from disarming your

system.

AutoArming™

If this feature is enabled and you forget to remotely arm your XL500, the system will

arm itself automatically (“passively”)30 seconds after the vehicle doors are closed. For

your convenience, if you re-open any door(s) within the 30-second countdown,

AutoArming will restart from the beginning once all doors are closed. Your XL500

includes these additional AutoArming features:

AutoArming enable/disable:If you prefer, you may deactivate or reactivate the

AutoArming feature. See User-selectable features on page 6.

AutoArm & Lock: To ensure that you can’t accidentally lock your keys inside

the car, the system is factory-set not to lock the doors upon AutoArming. To

change this setting, see User-selectable features on page 6.

NOTE: To prevent AutoArming of the system when fueling the vehicle, either

enable valet mode (see below) or leave one of the doors open.

Valet mode

Whenever the system is put in valet mode, all of the system’s security features are

switched off. At various times, you will need to turn the system off. For instance,

when having your car serviced, washed or parked by a valet.

NOTE: If you temporarily lose the use of your remote controls, you can

disarm the system by enabling valet mode.

To enable valet mode:

1. Turn the ignition switch to its “ON” position or start the engine.

2. Flick the valet switch. The system’s LED will glow continually for on-going

visual confirmation of valet mode.

To exit valet mode:

1. Turn the ignition switch to its “ON” position or start the engine.

2. Flick the valet switch. The LED will turn off to confirm that the system is in its

normal operating mode.

Magnetic Resonance Sensor™

The Magnetic Resonance Sensor detects intrusion-related vibrations and impacts. For

an even greater level of security, consider Clifford Electronics optional sensors: the

Glass Tampering Sensor (detects attempts to break any of your vehicle’s windows)

OmniSensor (a digital analysis vibration/impact sensor) and/or the Proximity Sensor

(a passenger compartment radar sensor, particularly important for convertible and

other open-top cars).

AutoTesting™

Each time you remotely arm your XL500, it will automatically perform an extensive

series of tests on all the system’s triggers and sensors. If a trigger malfunction is

found, you will be visually and audibly alerted immediately with 4 chirps and 4

flashes of the parking lights instead of the usual 2 and 2. If a sensor is

malfunctioning, you will receive the usual 2 chirps and 2 flashes, then, a few

seconds later, there will be 4 chirps and 4 flashes.

Automatic malfunction bypass

To provide the utmost protection even if a system component malfunctions, your

XL500 will automatically bypass the faulty point and arm all other triggers and

sensors to provide the utmost possible protection until you can have the system

serviced by your local Authorized Clifford Dealer.

FACT™— False Alarm Control and Test

With FACT, you’ll never experience repeated false alarms. If your siren goes off,

DO NOT remotely disarm the system while the siren sounds; allow it to run for the

full siren duration of 30 seconds. Before sounding the siren a second time, the

system automatically checks for another activated trigger to verify that an intrusion

is in progress. Should the siren sound again, you will know for sure that someone is

tampering with your vehicle. (To disable FACT, see User-selectable features on

page 6.)

Prior intrusion attempt alert

When you remotely disarm, if you hear 3 chirps instead of the usual one chirp it

means that the system foiled an intrusion attempt while you were away.

How to interpret the chirps

When you use the remote control, the system will respond with chirps and, optionally,

flashes the parking lights to confirm system status. The meaning of these

acknowledgments is as follows:

Chirps Meaning

1Alarm is disarmed, you may enter the vehicle

2Alarm is armed and protecting your vehicle

2 and then 4 Alarm is armed, but there is a sensor malfunction (see AutoTesting above)

3Alarm is disarmed, but there was an intrusion attempt (see Prior intrusion attempt alert above)

4Alarm is armed, but there is a trigger malfunction (see AutoTesting above)

Optional automatic starter interrupt

Your XL500, if equipped with an optional relay, will automatically prevent engine

from being started while the system is armed.

How to interpret the LED status indicator

The LED status indicator on your vehicle’s dashboard or console is used to inform

you of the system status:

LED Condition Meaning

Off System is disarmed and in normal operating mode (i.e., valet mode is off)

On Valet mode is on, the vehicle can be driven or serviced without having to disarm

Flashing System is armed and protecting your vehicle

Pause between flashes Either a malfunction or an intrusion was attempted (see page 4)

High-output siren

Provides these additional features:

Patented automatic noise abatement: Limits alarm sounding to no more than

three minutes even if a door is left open in the wake of an intrusion attempt.

This ensures against excessive battery drain and towing of the vehicle due to

noise pollution.

Remote controlled chirp muting: Remote controlled chirp muting capabilities

are especially valuable when parking late at night in a quiet residential area. To

arm or disarm silently, simply press both buttons I+II on your remote control

instead of the usual button I.

SmartPowerUp™

If power is ever removed and restored in an attempt to steal your car,

SmartPowerUp automatically will re-arm the system, sound the siren, flash the

parking lights and electronically interrupt the starter. To disconnect power for

servicing, simply insert your key into the ignition and turn it to the “ON” position

before reconnecting power. Your XL500 recognizes this an an authorized power

reconnection and will not alarm.

User-selectable features

Your XL500 vehicle security system allows you to set many of its features to your own

personal preferences. We have made the programming procedures very simple: to make

a change, you just flick the valet switch a few times. The system comes from the factory

with all of its features pre-programmed as noted in the table below. To change any of the

settings, use the procedure noted. To restore the feature to its factory setting, just repeat

the procedure:

1. Select the feature you wish to program from the table below and on the following

page. Note the number of flicks and chirps associated with that feature.

2. Turn your vehicle’s ignition switch to its “ON” position.

3. Immediately flick the valet switch back and forth, counting the number of chirps

you hear. Stop when you reach the number associated with the feature you selected.

4. If noted, perform the “secondary action.”

5. After a 3-second pause, you will hear 1 chirp to confirm that you have changed

the setting of the feature. Turn the ignition off.

6. Repeat steps 1-5 for any other features you wish to program.

Programming table for user-selectable features

Feature Factory

setting

# of flicks

and

chirps

Secondary

action

Program

completion

confirmation Result

AutoArming ON 4—1 chirp 3

seconds after

last step Change state from

ON to OFF or vice-versa

AutoArm

& Lock OFF 5—1 chirp 3

seconds after

last step Change state from

ON to OFF or vice-versa

FACT —

False Alarm

Control and

Test ON 12 —1 chirp 3

seconds after

last tap Change state from

OFF to ON or vice-versa

Add a New

Remote to

Channel 1

(arm/disarm) —13 Press remote control button I1 chirp Button I/channel 1 code

of the new remote control

has been memorized

Add a New

Remote to

Channel 2

(remote

accessory)

—14 Press remote control button II 2 chirps Button II/channel 2 code

of the new remote control

has been memorized

Add a New

Remote to

Channel 3

(silent

arm/disarm)

—15 Simultaneously press

remote control buttons I+II 3 chirps Buttons I+II/channel 3 code

of the new remote control

has been memorized

Adding new remote controls

Your XL500 will respond to as many as two Clifford 3-channel remote controls.

You can buy additional remote controls from any Authorized Clifford Dealer (or

call our 24-hour Customer Service Department at 800-824-3208) and program them

into the system yourself. To add a new remote control to the system, use the

procedures noted in the User-selectable features section on page 6.

How to erase the codes of lost or stolen remote controls

If one of your remote controls is ever lost or stolen, you can push its digital codes

out of system memory to make sure that the missing remote control can never be

used to disarm your system. Just use the Adding new remote controls procedures

noted in the User-selectable features section on page 6 for a total of two times (if

you have only one remote control, program it twice).

Example

To change the AutoArming feature from its factory setting of on to off, you

would do the following:

Turn the ignition key to the ON position.

Immediately flick the valet switch 4 times (you a chirp each time you

flick the switch for a total of four chirps).

Wait 3 seconds. The system will sound one more chirp to confirm that

the AutoArming setting has been changed.

Turn the ignition off (you’ll hear 3 chirps to confirm exit of program

mode).

That’s all there is to it!

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clifford Autoalarmanlage Handbücher

Clifford

Clifford Model RSX1.2 Bedienungsanleitung

Clifford

Clifford 5906V Bedienungsanleitung

Clifford

Clifford cx-427 Bedienungsanleitung

Clifford

Clifford SE 3030 Bedienungsanleitung

Clifford

Clifford GP500 Bedienungsanleitung

Clifford

Clifford SE 2020 Special Edition Bedienungsanleitung

Clifford

Clifford Concept 650 Bedienungsanleitung

Clifford

Clifford Model RSX1.2 Bedienungsanleitung

Clifford

Clifford Cyber 5 Bedienungsanleitung

Clifford

Clifford 420.4X Bedienungsanleitung

Clifford

Clifford SuperNova II Bedienungsanleitung

Clifford

Clifford Matrix 12 Bedienungsanleitung

Clifford

Clifford 22CX Bedienungsanleitung

Clifford

Clifford intelliGuard 750 Bedienungsanleitung

Clifford

Clifford 5606X Bedienungsanleitung

Clifford

Clifford BlackJax 4 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Clifford

Clifford Smart Remote Starter Bedienungsanleitung

Clifford

Clifford Nova 200LE Bedienungsanleitung

Clifford

Clifford 330.3X Bedienungsanleitung

Clifford

Clifford 520.4X Bedienungsanleitung

Clifford

Clifford AvantGuard 5.1 Bedienungsanleitung

Clifford

Clifford Centurion Bedienungsanleitung

Clifford

Clifford 4115X Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung

Megalarm

Megalarm MEGA 3600 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung