Clifford GP500 Bedienungsanleitung

For the latest vehicle wiring

information and for wiring diagrams

and servicing information on older

Clifford products 24-hour dealer

website:

www.clifforddealer.com

USA Toll Free Technical Support:

800-444-4667

UK Technical Support Free Phone:

800-526708

Standard Features of GP500

Note:ThesystemcurrentdrawofGP500is5mAplusor

minus 0.5mA. Voltage operating range is 9V to 16V.

❑Lifetime Warranty

❑EC 97/24 Approved

❑Weather Resistant

❑Two ACG™ 2 Remote Controls

❑Extended Range

❑Built-In Two-Point Immobilizer™

❑Helmet Theft Protection System

❑Fully Adjustable Dual-LevelPiezo Sensor™

❑Digital Dual-Zone Tilt/Motion Sensor

❑Self-Powered Siren with Key Override

❑Built-In Indicator Light Flasher with On-Board Relay

❑User-Selectable AutoArming™

❑Advanced CMOS Microcomputer

Installation Manual/4991

Standard Features of GP500 (Cont’d)

❑BikeBeacon™ Vehicle Locator System

❑FACT—False Alarm Control and Test

❑Patented SmartPowerUp™ 2

❑Patented Smart AutoTesting™

❑Five-Event TotalRecall™

❑Remote Panic

❑Patented Smart Prior Security Breach Alert

❑Multiple-Vehicle Control

❑Patented Remote Control Code Learning

❑High-Luminescence LED with Automatic

Battery-Saving Mode

❑All Black Wiring

2GP500

System Connections

Control Unit

The GP500 control unit must be installed as far away

as possible from the engine. Under no circumstances

should the unit be installed close to hot or moving

parts.

1.Remove the seat and any side panels necessary to expose the

battery terminals, indicator light wiring and ignition wires.

2.Select a location under the seat to mount the GP500 control

unit. The control unit must be mounted in a flat and level

position with the side bearing the Clifford logo facing upward.

This location must stay dry and allow the use of screws or tie

wraps to securely fasten the control unit to metal. Avoid hot or

moving parts.

3.Mount the GP500 control unit using screws or tie wraps, but do

not permanently affix it until all wiring and testing is complete.

Installation Manual/499 3

LED Status Indicator

Select a prominent location on the motorcycle that is highly visible

from all directions. Discuss placement with the owner.

1.Verify there is adequate space to accommodate the LED, then

drill a 4mm (#21 drill bit) hole and route the wires through it.

2.Mate the BLACK wire connector labeled LED (+) to the LED’s

VIOLET wire as shownin the diagram on page 5.

3. Mate the BLACK wire labeled LED (-) tothe LED’s BLACK

wire as shown in the diagram on page 5.

4. Press the LED into place.

PlainView 2 Coded Programming Switch

1.Discuss placement of the switch with the vehicle owner and

avoid placing the switch where it can be pressed accidentally.

2.Mount the switch on to a clean, dry surface using the supplied

adhesive tape.

3.Mate the switch’s locking connectors to the locking connector from

the control unit.

4GP500

Installation Manual/4995

Indicator Lights

1.Connect a voltmeter lead to ground.

2.Access the indicator light harness near the indicator light switch,

and turn on the left indicator light.

3.Probe the wires. When you probe the correct left indicator light

wire, the voltmeter will read +12V when the indicator lights

illuminate, and 0 volts when they turn off.

4. Turn on the right indicator light and repeat step 3.

5.Connect one of the two BLACK wires labeled Indicator Light

+12Vto the left indicator light circuit and the other wire labeled

Indicator Light +12Vto the right circuit as shown in the

illustration on page 5 .

Starter and Ignition Immobilization Circuits

1.Locate the ignition switch wireloom under the gauges or

key/ignition switch and use a voltmeter to locate the one wire

that carries +12V throughout BOTH the cranking AND

engine running cycles, and 0 volts when the ignition is off.

2. Start the engine, then cut the ignition wire. The engine should

stop running.

3.As shown on page 5, connect the BLACK wire with the Ignition

Input +12 Voltslabel to the key sideof the cut ignition line.

6GP500

4.Connect the BLACK wire with the Ignition Output +12 Volts

label to the coil sideof the cut ignition line.

5.Use a voltmeter to locate the one wire that carries +12V during

the cranking cycle ONLY. Cut this wire, then try to start the

engine. It should not crank.

6. Connect the BLACK wire with the Starter Input+12 Volts label

to the key sideof the cut starter line.

7.Connect the BLACK wire with the Starter Output+12 Volts

label to the starter side of the cut starter line.

NOTE: The starter circuit may carry a very high

current. Be certain that the starter wire connections

are solid. Each immobilization circuit can carry 15

amps.

8.Remove the labels from each of the wires.

Self-Powered Siren with External Key Override

If a thief disconnects power and/or cuts any or all of the wires while

the system is armed, the siren will sound for five minutes and then

reset. If power must be disconnected for servicing, an override key is

provided to turn the siren off. Unlike other back-up battery sirens

Installation Manual/4997

that constantly drain the vehicle battery, Clifford’s design draws

charging current only when the ignition is on (i.e., engine running).

NOTE: The motorcycle must be ridden for eight hours

after the siren has been installed in order to

sufficiently charge the siren’s back-up battery.

1.Select a location for the siren under the seat or behind a side

cover. Keep the siren away from direct exposure to rain and

moisture. Avoid hot or moving parts. Also make sure there is

sufficient clearance for the mounting screws behind the

mounting surface.

2.You must firmly secure the siren using all three sheet metal

screws supplied. Mount the siren away from areas of water ingress

or excessive heat. Point the siren down to avoid moisture.

3.Connect the siren’s BROWN wire to the BLACK wire labeled

Siren Output (-).

4. Connect the siren’s BLUE wire to the BLACK wire labeled

Ignition Output +12V.

5.Connect the RED wire to the 5 amp fuse connected to the

battery positive cable clamp.

6.Connect the BLACK wire to ground.

8GP500

Andere Handbücher für GP500

Inhaltsverzeichnis

Andere Clifford Autoalarmanlage Handbücher

Clifford

Clifford 330.3X Bedienungsanleitung

Clifford

Clifford Concept 60 Bedienungsanleitung

Clifford

Clifford SmartWindows 4 Bedienungsanleitung

Clifford

Clifford Concept 100 Bedienungsanleitung

Clifford

Clifford Matrix RS1.1 Bedienungsanleitung

Clifford

Clifford Cyber 4 Bedienungsanleitung

Clifford

Clifford AvantGuard 5.1 Bedienungsanleitung

Clifford

Clifford SE 2020 Special Edition Bedienungsanleitung

Clifford

Clifford Cyber 5 Bedienungsanleitung

Clifford

Clifford 300UK Betriebsanleitung

Clifford

Clifford Concept 650MkII Bedienungsanleitung

Clifford

Clifford 590.4X Bedienungsanleitung

Clifford

Clifford 20.5X Bedienungsanleitung

Clifford

Clifford Model RSX1.2 Bedienungsanleitung

Clifford

Clifford Auto Immobilizer Bedienungsanleitung

Clifford

Clifford 5706X Bedienungsanleitung

Clifford

Clifford Prime Level Three Bedienungsanleitung

Clifford

Clifford Falcon II Bedienungsanleitung

Clifford

Clifford Arrow II Bedienungsanleitung

Clifford

Clifford Sabre Bedienungsanleitung

Clifford

Clifford RS1.1L Bedienungsanleitung

Clifford

Clifford Concept 450 Bedienungsanleitung

Clifford

Clifford 4706X Responder LC3 Bedienungsanleitung

Clifford

Clifford SE 5000 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung

Python

Python 660XP Bedienungsanleitung

Megalarm

Megalarm MEGA 3600 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung