COBHAM 3.8m Offset Antenna Bedienungsanleitung

For further information please contact:

Cobham SATCOM land Systems

Patriot Products

704 North Clark Street

Albion, Michigan 49224 USA

Tel: (01) 517 629 5990

Fax: (01) 517 629 6690

[email protected]

www.cobham.com/patriot

3.8m Oset Antenna

Receive only and Transmit / Receive

The most important thing we build is trust

Document number here in this font and color

www.cobham.com/patriot

This COBHAM SATCOM Patriot product is warranted to be free from defects in material and

workmanship under normal use and service. Patriot antenna products shall repair or replace defective

equipment, at no charge, or at its option, refund the purchase price, if the equipment is returned to Patriot

products not more than twelve (12) months after shipment. Removal or reinstallation of equipment and its

transportation shall not be at cost of COBHAM SATCOM Patriot product except Patriot product shall return

repaired or replaced equipment freight prepaid.

This Warranty shall not apply to equipment which has been repaired or altered in any way so as to affect

its stability or durability, or which has been subject to misuse, negligence or accident. This Warranty does

not cover equipment which has been impaired by severe weather conditions such as excessive wind, ice,

storms, lightning, or other natural occurrences over which COBHAM SATCOM Patriot products has no

control, and this Warranty shall not apply to equipment which has been operated or installed other than in

accordance with the instructions furnished by COBHAM SATCOM Patriot products.

Claimants under this Warranty shall present their claims along with the defective equipment to COBHAM

SATCOM Patriot products immediately upon failure. Noncompliance with any part of this claim procedure

may invalidate this warranty in whole or in part.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER AGREEMENTS AND WARRANTIES, ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN DURATION

TO THE DURATION OF THIS WARRANTY. PATRIOT ANTENNA DOES NOT AUTHORIZE ANY PERSON TO AS-

SUME FOR IT THE OBLIGATIONS CONTAINED IN THIS WARRANTY AND

PATRIOT ANTENNA NEITHER ASSUMES NOR AUTHORIZES ANY REPRESENTATIVE OR OTHER

PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE EQUIPMENT

DELIVERED OR PROVIDED.

IN NO EVENT SHALL COBHAM SATCOM PATRIOT ANTENNA PRODUCTS BE LIABLE FOR ANY LOSS OF

PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL OR

CONSEQUENTIAL DAMAGES OF ANY KIND.

In no event shall COBHAM SATCOM Patriot products be liable for damages in an amount greater than the

purchase price of the equipment.

Some states do not allow limitations on how long an implied warranty lasts, or allow the exclusion or

limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to

you.

COBHAM SATCOM Patriot products has the right to void the warranty when the antenna is installed by

someone other then a certied installer.

LIMITED TWELVE (12) MONTH WARRANTY

Product Serial Number- _________________

Date Purchased- _________________

Cobham SATCOM Land Systems

Patriot Products

704 North Clark Street

Albion, MI 49224 USA

Tel: (517)629-5990

Fax: (517)629-6690

[email protected]

www.cobham.com/patriot

1. Perform as many functions as possible on the ground.

2. Watch out for overhead power lines. Check the distance to the power lines before starting

installation.

We recommend you stay a minimum of 6 meters (20 feet) from all power lines.

3. Do not use metal ladders.

4. Do not install antenna or mast assembly on a windy day.

5. If you start to drop antenna or mast assembly, get away from it and let if fall.

6. If any part of the antenna or mast assembly comes in contact with a power line, call your

local power company. DO NOT TRY TO REMOVE IT YOURSELF! They will remove it safely.

7. Make sure that the mast assembly is properly grounded.

WARNING

Assembling dish antennas on windy days can be dangerous. Because of the antenna surface,

even slight winds create strong forces. For example, a 1.0m antenna facing a wind of 32 km/h

(20 mph) can undergo forces of 269 N (60 lbs.). Be prepared to safely handle these forces at un-

expected moments. Do not attempt to assemble, move or mount dish on windy days or serious,

even fatal accidents may occur. COBHAM SATCOM Patriot antenna product is not responsible or

liable for damage or injury resulting from antenna installations.

INSTALLATION OF THIS PRODUCT SHOULD BE PERFORMED ONLY BY A PROFES-

SIONAL INSTALLER AND IS NOT RECOMMENDED FOR CONSUMER D.I.Y.

(DO-IT-YOURSELF) INSTALLATIONS.

IMPORTANT!!!

WATCH FOR WIRES!

Installation of this product near power lines is dangerous. For your

own safety, follow these important safety rules.

www.cobham.com/patriot

Item# Part Description Part Numbe Quantity

1 ASSY, 3.8M OFFSET A-LEFT PANEL 238204 1

2 ASSY,3.8M OFFSET A-RIGHT PANEL 238205 1

3 ASSY,3.8M OFFSET B PANEL 238206 2

4 ASSY,3.8M OFFSET C-LEFT PANEL 238208 1

5 ASSY,3.8 MTR OFFSET C-RIGHT PANEL 238209 1

6 ASSY,3.8M OFFSET RADIAL BEAM A 238210 1

7 ASSY,3.8M OFFSET RADIAL BEAM B 238211 4

8 ASSY,3.8M OFFSET RADIAL BEAM C 238213 2

9 ASSY,3.8M OFFSET 90” BACK SUPPORT 238223 2

10 ASSEM, CURFING 42.68” “B” 238910 2

11 ASSEM, CURFING 46.79” “A” 238911 2

12 ASSEM, CURFING 57.00” “C” 238912 2

13 TUBE,3.8M OFFSET FEED SUPPORT 238993 2

14 ASSEM, 3.8M OFFSET FEED PLATE 238996 1

15 MOUNT,3.8M OFFSET KINGPST AND YOKE 238308 1

16 ASSY,3.8M OFFSET MAST STRUT 238307 1

17 ASSY,3.8 MTR OFFSET HUB 238214 1

18 ASSY,3.8M OFFSET KP ELEV.ROD 238302 1

PG 7 PLATE,3.8M OFFSET KP AZ LOCKDOWN 238304-04 1

PG 7 ASSY,3.8M OFFSET KP AZ LOCKDOWN 238304 1

PG 7 ASSY,3.8M OFFSET KP AZIMUTH ROD 238303 1

PG 9 SHIM, 2.4M BOOM .25” 224132 4

PG10 ANGLE,3.8M OFFSET HUB 238214-12 28

PG11 ASSY,3.8M OFFSET 65” BACK SUPPORT L 238224 1

PG11 BRKT.,3.8M OFFSET BACK SUPPORT 238222 21

PG11 ANGLE,3.8M 45”BACK SUPPORT 238219 4

PG11 ASSY,3.8M OFFSET 65” BACK SUPPORT R 238225 1

PG11 ANGLE,3.8M 32” BACK SUPPORT 238220 4

PG11 ASSY,3.8M OFFSET 65” BACK SUPPORT L 238224 1

PG11 ASSY,3.8M OFFSET 65” BACK SUPPORT R 238225 1

PG11 ANGLE,3.8M OFFSET 90” BACK SUPPORT 238223 2

PREBAG,3.8M.OFFSET REFLECTOR HWD. 3HP38011 1

PAINT, OFF WHITE TOUCH UP, 8 OZ. 4M9055 1

www.cobham.com/patriot

Grounding Rod Clamp & Grounding Block - As required by

National Electric Code or local codes.

Ground Wire - #10 solid copper or as required by National

Electric Code or local codes.

Coaxial Cable (Size & Length required).

Concrete & Rebar (See Foundation Appendix A).

Preinstallation materials checklist

1- 5/32”, 3/16” , 1/4” allen wrenches

2- Combination wrenches -

7/16”, 1/2”, 9/16”, 3/4”, 15/16”, 1-1/8”

1- Large Crescent wrench or Pipe Wrench with

3in. jaw opening

1- Inclinometer (for sighting in)

1- Compass (for sighting in)

1- Impact drill

(for drilling cement anchor holes)

Tools Needed

Reference Drawing

Refer to Parts and Hardware list on page 5 for part descriptions. This figure is an overall assembled an-

tenna and can assist the installer with locating parts and understanding the relationship between compo-

nents.

15 16

www.cobham.com/patriot

1. Place the King Post Mast assembly onto the foundation threaded rods and secure with nuts

and washers from the foundation hardware pack. Be sure to use the 4-base reinforcement

plates provided as shown.

NOTE: The mast should be pointed due south (northern hemisphere sites)

2. Attach ASSY,3.8M OFFSET MAST STRUT (pt# 238307) using 5/8in hardware. Mark area on

foundation for cement anchor placement location (see page 16 for foundation details and

anchor requirments)

NOTE: The use of an impact drill for drilling cement will be needed.

3. Assemble either the Fixed or Motorized Mount Assembly Kit option purchased with the system.

King Post Assembly Placement

Installation Procedure

1. Place the King Post Mast assembly onto the foundation threaded rods and secure with nuts and washers from the

foundation hardware pack. Be sure to use the 4-base reinforcement plates provided as shown.

NOTE: The mast should be pointed due south (northern hemisphere sites)

2. Attach the Mast Strut assemblies using 5/8in hardware, and 5/8in cement anchor hardware at the pad.

NOTE: The use of an impact drill for drilling cement will be needed.

3. Assemble either the Fixed or Motorized Mount Assembly Kit option purchased with the system.

See Appendix B for Fixed Mount Assembly Kit Option

See Appendix C for Motorized Mount Assembly Kit Option.

Mount Assembly

Cement

Anchor

Hardware

Base Reinforce-

ment Plates (4)

PLATE, KP BASE

(pt# 245000-204)

ASSY,3.8M OFFSET

MAST STRUT

(pt# 238307)

Area to be marked

see Pg.16 for approximent location for

anchor placement

www.cobham.com/patriot

1. Attach 3.8m OFFSET AZ LOCK DOWN ASSEMBLY (PT# 238304) and LOCKDOWN PLATE

(pt# 238304-04) to Kingpost assembly using (4) 1/2nc X 2-1/4 botls and matching washers and nuts.

Leave hardware lose at this time.

2. Slide AZ LOCK DOWN ROD (pt# 238303) thru tube on lock down plate as pictured below. Leave

hardware lose at this time.

3. Attach yoke end of AZ LOCK DOWN ROD to yoke using 3/4” x 2.00” shoulder bolt and 5/8” nut

washers as pictured below.

4. Tighten all hardware once proper AZ angle has been set.

NOTE:

All hardware mentioned above

can be found in hardware bag

AZ LOCK DOWN ROD

(pt# 238303)

OFFSET AZ LOCK DOWN ASSEMBLY (PT#

238304)

LOCKDOWN PLATE

(pt# 238304-04)

Az Lockdown Assembly

www.cobham.com/patriot

Hub Assembly

1. Place the Hub onto the A-frame using the pre-installed shoulder bolt hardware as shown.

2. Connect the Fixed or Motorized accessories per the attached Appendixs (Fixed shown)

For Fixed Mount Option- See Appendix B.

For Motorized Mount Option- See Appendix C

1. Attach ASSY,3.8M OFFSET KP ELEV.ROD (pt#238302) to yoke pick up detail using

3/4”X 2.00” shoulder bolt, 5/8 nut and washer.

2. Place 3.8M OFFSET KP ELEV.PIVOT BLOCK (pt# 238003) on to 3.8M OFFSET KP ELEV.ROD

(pt#238302) as pictured below. (Leave THIS hardware loose at this time)

2. Place the HUB ASSEMBLY (pt# 238214) on to the A-frame using the pre-installed shoulder

bolt hardware as shown.

3. Attach 3.8M OFFSET KP ELEV.PIVOT BLOCK (pt# 238003) to HUB ASSEMBLY using

(2) 3/4nc X 1-1/2 bolts and matching lock washers.

4. Tighten all hardware at this time.

NOTE:

All hardware mentioned above

can be found in hardware bag

#3HP38013.

3.8M OFFSET KP ELEV.PIVOT

BLOCK (pt# 238003)

3.8M OFFSET KP ELEV.ROD

(pt#238302)

HUB ASSEMBLY

(238214)

Hub Assembly

www.cobham.com/patriot

1. Install TUBE,3.8M OFFSET FEED SUPPORTS (pt# 238993) using (4) 1/2nc x 7.00” bolts, matching

washers and (4) FEED BOOM SHIMS (pt# 224132).

2. Tighten all Feed Support hardware.

Feed Boom Install

FEED BOOM SHIMS

(PT#224132)

TUBE,3.8M OFFSET FEED

SUPPORTS (pt# 238993)

This hole, closest

to the edge, up.

Feed Plate Assembly Install

1. Install 3.8M OFFSET FEED PLATE ASSEMBLY

(pt# 238996) using (4) 3/8nc x 3.00” bolts,

washers and nuts.

NOTE:

All hardware mentioned above can

be found in hardware bag #3HP38016.

NOTE:

Make sure that feed booms

are placed as pictured below

with feed plate mounting

holes up.

www.cobham.com/patriot

Apply wax here

to aid in sliding

radial beams in to hub

Apply wax here

to aid in sliding

radial beams in to hub

1. Fasten (4) ANGLE,3.8M OFFSET HUB (pt# 238214-12) to each Radial

Beam as shown, using (4) 3/8in shoulder (1) 5/16” washer, and nut per.

2. Adjust the Hub into the position shown, and select 3.8M OFFSET RADIAL

BEAM C ASSEMBLY (pt#238213), and place into the outermost location

inside the Hub. Fasten using 3/8in shoulder bolt hardware, (1) 5/16”

washer, nut per lose. Do the same with the opposing 3.8M OFFSET

RADIAL BEAM C ASSEMBLY (pt#238213).

NOTE: Hard to reach hardware can be accessed by reaching inside and

around the end of the Radial Beam to reach the back side.

3. Repeat step 2 for 3.8M OFFSET RADIAL BEAM B ASSEMBLY (pt# 238211)

3.8M OFFSET RADIAL BEAM A ASSEMBLY (pt# 238210)

4. Tighten all Radial Beam hardware in steps 1 through 3.

ANGLE,3.8M OFFSET HUB

(238214-12)

RADIAL BEAM

ASSEMBLY

NOTE: Shoulder bolts are fastened from the

inside of the Hub with the washers and nuts

on the outside.

All hardware can be found in bag

#3HP38011

Radial Beam Install

Inhaltsverzeichnis

Andere COBHAM Antenne Handbücher

COBHAM

COBHAM Sailor 150 FleetBroadband Bedienungsanleitung

COBHAM

COBHAM Sea Tel Bedienungsanleitung

COBHAM

COBHAM Sea Tel Tracker 6000 Bedienungsanleitung

COBHAM

COBHAM SAILOR 600 VSAT Ka Bedienungsanleitung

COBHAM

COBHAM Sailor 500 FleetBroadband Bedienungsanleitung

COBHAM

COBHAM EXPLORER 6075LX Leitfaden

COBHAM

COBHAM EXPLORER 8100 GX Bedienungsanleitung

COBHAM

COBHAM Sea Tel Bedienungsanleitung

COBHAM

COBHAM EXPLORER 5075GX Bedienungsanleitung

COBHAM

COBHAM SAILOR 1000 XTR Ku 8W Gebrauchs- und Pflegehandbuch

COBHAM

COBHAM SAILOR 900 Bedienungsanleitung

COBHAM

COBHAM SAILOR 1000 XTR Ku 8W Bedienungs- und Sicherheitshinweise

COBHAM

COBHAM EXPLORER 540 Bedienungsanleitung

COBHAM

COBHAM Sailor 900 VSAT Bedienungsanleitung

COBHAM

COBHAM EXPLORER 8100 Bedienungsanleitung

COBHAM

COBHAM S-67-175992 Gebrauchs- und Pflegehandbuch

COBHAM

COBHAM SAILOR 1000 XTR Ku 8W Bedienungsanleitung

COBHAM

COBHAM Sailor 900 VSAT Bedienungsanleitung

COBHAM

COBHAM Sea Tel 6011-4 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6120 Bedienungsanleitung

COBHAM

COBHAM EXPLORER 6075LX Bedienungsanleitung

COBHAM

COBHAM SAILOR XTR Ku Bedienungsanleitung

COBHAM

COBHAM SAILOR 60 GX-R2 4.5 W Bedienungsanleitung

COBHAM

COBHAM SAILOR 900 Ka Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch

Labgear

Labgear LABHG32T Bedienungsanleitung