Cobra 602-2000B Bedienungsanleitung

23801 E. La Palma Ave., Yorba Linda, CA 92887 Ph. 714.692.8180 Fax. 714.692.5016

www.cobrausa-vtwin.com

01/20

*Cobra®recommends you always wear a helmet while riding. Please never operate your motorcycle while under

the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.

Items Supplied >

1 - DETACHABLE BACKREST

2 - COIL-OVER SPACERS

Application(s) >

HARLEY:

DRESSER 09-20

Instruction Manual >

Read all instructions carefully and completely before installing your new Backrest!

NOTE: You must install either a COBRA Mounting Kit (602-2100/602-2101) or a Harley Davidson 2-

point or 4 point Mounting kit before installing this backrest.

1. Remove the saddle bags carefully.

2. Install the mounting kit per the instructions that came with that kit.

3. If you are installing this backrest on a 2015-16 Street Glide Special or a 2015-16 Road Glide Special with coil-

over rear shocks you must first install the spacers supplied with the backrest between the right rear coil-over

shock and the frame and swing arm. See FIGURE 1. This will space the coil-over out far enough for the backrest

to fit properly. If your motorcycle is equipped with air shocks you do not need to install the spacers and can skip

to step 8.

SPECIAL NOTE: Some 2015 Street Glide Specials and Road Glide Specials came with the right rear coil-over

shock mounted upside down with the shock shaft pointed up. Make sure to flip the shock over if this is the case.

The shock shaft needs to be facing down as in FIGURE 1.

4. First, remove the top bolt of the right rear coil-over shock. See FIGURE 1.

5. Insert the supplied spacer between the frame and the coil-over shock and then re-install the bolt and tighten to

factory specs.

6. Then remove the bottom bolt from the right rear coil-over shock and insert the supplied spacer between the coil-

over and the swing arm. Re-install the bottom bolt and tighten to factory specifications. See FIGURE 1.

602-2000 / 602-2000B

Page 1 of 2

DOCUMENT NO. 0017 REV. A

FIGURE 1

ONLY FOR MODELS EQUIPPED

WITH COIL-OVER SHOCKS

ADD SPACER BETWEEN

COIL-OVER AND

SWING ARM

ADD SPACER BETWEEN

COIL-OVER AND

FRAME

SHOCK SHAFT

SHOULD BE DOWN

23801 E. La Palma Ave., Yorba Linda, CA 92887 Ph. 714.692.8180 Fax. 714.692.5016

www.cobrausa-vtwin.com

01/20

Instruction Manual >

602-2000 / 602-2000B

Page 2 of 2

8. Once the spacers have been installed on the right side coil-over (if applicable) and the mounting kit has been

installed you can install the backrest by inserting the front portions of the backrest brackets over the mounting

bosses of the rear shocks. See FIGURE 2. Make sure to insert the backrest all the way onto the bosses.

9. Then slowly rotate the backrest downward so the rear portion of the backrest brackets slips over the mounting kit

bushings. See FIGURE 2.

10. If you are using a Harley Mounting Kit you may need to adjust the width of the mounting kit bushings to align

them with the width of the backrest brackets. The Harley Mounting Kits come with spacers that may need to be

added or removed to align the width of the mounting kit bushings with the width of the backrest. Please see the

instructions that come with the mounting kit for more details.

11. Also, some Harley Mounting Kits come with oval shaped mounting bushings. These mounting bushings may

need to be rotated around the center axis of the bushing to allow for a secure fit of the detachable latch pin.

Please see the instructions of the mounting kit for more details.

12. Pull backward on both detachable latch knobs and then push downward on the backrest to allow the backrest to

sit completely on the mounting kit bushings. Then release the detachable latch knob to fully engage the latch pin

underneath the mounting kit bushing. See FIGURE 3.

13. Always check to make sure both detachable latch pins are fully engaged on the bottom of the mounting kit

bushing. Failure to fully engage the detachable latch pin could cause the backrest to come loose while riding.

14. Make any adjustments to the mounting kit bushings until the detachable backrest goes on and off easily.

15. Once all the adjustments have been made reinstall the saddle bags.

16. Before each ride, check to make sure the detachable latches are fully engaged underneath the mounting

bushings.

17. Check the tightness of all the screws after the first ride and after the first 500 miles.

DOCUMENT NO. 0018 REV. A

AIR SHOCK

MOUNTING

BOSS

MOUNTING

KIT

DETACHABLE

LATCH KNOB

MOUNTING KIT

BUSHING

FIGURE 2

DETACHABLE

LATCH PIN

To clean your black accessory use a liquid based soap detergent, such as dishwashing soap applied with a soft cloth and

rinse with clean water. Note: Avoid abrasive cleaning methods such as granular or dry cleansers, simple green, Scotch-

Brite or steel wool pads. Abrasives may breach the coating and shorten life.

FIGURE 3

MAKE SURE

LATCH PIN IS

FULLY ENGAGED

UNDER BUSHING

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cobra Motorradzubehör Handbücher

Cobra

Cobra 601-2108 Bedienungsanleitung

Cobra

Cobra FLHC 2018 Bedienungsanleitung

Cobra

Cobra Fi2000 Bedienungsanleitung

Cobra

Cobra Fi2000 PowrPro Bedienungsanleitung

Cobra

Cobra Fi2000 Bedienungsanleitung

Cobra

Cobra 01-3265 Bedienungsanleitung

Cobra

Cobra Fi2000 Bedienungsanleitung

Cobra

Cobra 602-1103B Bedienungsanleitung

Cobra

Cobra 602-2612B Bedienungsanleitung

Cobra

Cobra POWRPRO Fi2000 Bedienungsanleitung

Cobra

Cobra 602-3000 Bedienungsanleitung

Cobra

Cobra 6255RB Bedienungsanleitung

Cobra

Cobra 602-2702 Bedienungsanleitung

Cobra

Cobra 602-2500 Bedienungsanleitung

Cobra

Cobra 602-2610B Bedienungsanleitung

Cobra

Cobra 02-4265 Bedienungsanleitung

Cobra

Cobra 602-2704 Bedienungsanleitung

Cobra

Cobra 602-3000 Bedienungsanleitung

Cobra

Cobra Ride Loud Bedienungsanleitung

Cobra

Cobra POWRFLO Bedienungsanleitung

Cobra

Cobra Fi2000 Bedienungsanleitung

Cobra

Cobra 06-0225-02B Bedienungsanleitung

Cobra

Cobra Classic LT Bedienungsanleitung

Cobra

Cobra Fi2000 Powrpro Bedienungsanleitung

Beliebte Motorradzubehör Handbücher anderer Marken

SRC

SRC B-TRK502-01-01-SL Bedienungsanleitung

3M Speedglas 9100 MP Bedienungsanleitung

hepco & becker

hepco & becker 6307520 00 01 Bedienungsanleitung

HOMCOM

HOMCOM AA0-077 Bedienungsanleitung

hepco & becker

hepco & becker 6307558 00 01 Bedienungsanleitung

Wunderkind Custom

Wunderkind Custom 106503-F15 Benutzerhandbuch

Dräger

Dräger HPS 3500 Bedienungsanleitung

M-WAVE

M-WAVE SKI Bedienungsanleitung

Kuryakyn

Kuryakyn 6212 Bedienungsanleitung

hepco & becker

hepco & becker 6507504 00 01 Bedienungsanleitung

Tool it

Tool it PROMAX LCD 9.13G Bedienungsanleitung

Custom Dynamics

Custom Dynamics TruWrapz Bedienungsanleitung

Roof

Roof RO200 CARBON Bedienungsanleitung

Kabuto

Kabuto Japan IBUKI Bedienungsanleitung

PUIG

PUIG 5051 Bedienungsanleitung

rizoma

rizoma ZTH050 Bedienungsanleitung

Joubert

Joubert 10001711 Bedienungsanleitung

Sperian

Sperian Optrel p420 Bedienungsanleitung