CODELOCKS 4000 Series Bedienungsanleitung

Number relating to picture Item CL4000GD

1 Front Plate *

2 Lever Handles x 2 *

3 Inside Lever Boss *

4 Spindle + Spacer *

5 Front Patch Fitting (LH or RH) *

6 2 Piece Internal Latch Patch fitting (with Gasket) *

7 Batteries x 4 'N cell' *

8 Front Plate Cylinder Keys *

9 Through Fixing Allen bolts x 2 *

10 Patch Fixing Allen bolts x 2 (short) *

11 Internal Patch Steel Cover Plate *

12 Strike Plate *

13 Allen Keys *

14 Front Plate Cylinder Cover *

15 Classroom Function Tailpiece *

BOX CONTENTS - Check the contents of the box are correct

TOOLS REQUIRED

Philips Screwdriver

Installation of Glass Door Lock

You should familiarise yourself with the lock and its operation before attempting to fit.

Locks are supplied as either RH or LH versions, check you have the correct product to suit the hand of your door.

The diagram below shows RH version.

1. With digital lock face down on a bench removing the transit strip from the rear of the lock by removing the two transit

screws.

2. Install batteries into lock ensuring that the positive and negative ends are correctly orientated.

3. Ensure that the clutch below the battery holder is in the correct position with orange and clack cable exiting the top left of

the clutch. If not rotate into the correct position.

4. Fit the front patch fitting to the frontplate with the two short transit bolts and tighten. NOTE – ensure cables are not

trapped.

5. Test the factory master code by pressing 1234. The blue light should signal to show a correct code. The red light will

signal after 5 seconds to show the code operation period has expired.

6. Fit the lever handle to the fronplate boss according to the hand of your door and secure with the grub screw.

7. Remove the steel coverplate from the latch patch fitting by unthreading the Nylon nut.

8. Ensure that the latch patch fitting is handed to suit our door. The hand can be changed by a combination of reversing the

latch head (via the securing screw) and /or by turning the latch patch fitting to 180 degrees.

9. The spindle supplied is suitable for glass doors up to 15mm thick. For doors thicker than 15mm please install the spacer

piece provided onto the long end of the spindle. Now take the internal latch patch fitting and pass the spindle through the

latch follower with the short end facing the code side. Push the spindle through until the washer rests against the patch lock.

10. Place the thin plastic gasket on the latch patch fitting so it is seated against the glass door and latch when assembled.

11. Holding the latch patch fitting in place take the frontplate assembly and fit over spindle.

12. Using the 2 through fixing bolts from the latch side secure the code side and latch side together, ensuring the lock is

aligned vertically and horizontally with the door.

13. Refit the steel coverplate to the latch patch fitting and secure with Nylon rut.

14. Take the internal lever boss and fit pushing firmly onto spindle. Secure with grub screw.

15. Fit internal lever onto boss according to hand of door and secure with grub screw.

Operation Check

A) Enter the mastercode; wait for the blue light and depress the lever which should retract the latch. After the red light,

depress the lever once more which should not retract the latch.

B) Depress the internal lever which should retract the latch.

If A) or B) do not work please check installation from step 12 and that the lock has not been set in passage function by key

(see programming instructions).

NOW – Change factory set Mastercode (see programming instructions).

3.5mm 16.5mm

20.5mm

29mm

65mm

38mm

24mm

60mm

10mm

61mm

142.5mm

159mm

45mm 45mm

Electronic Digital Patch Lock Template

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CODELOCKS Sperren Handbücher

CODELOCKS

CODELOCKS KL1000 NetCode Bedienungsanleitung

CODELOCKS

CODELOCKS CL255 Administratorhandbuch

CODELOCKS

CODELOCKS CL600 Bedienungsanleitung

CODELOCKS

CODELOCKS KL1050 C2 Bedienungsanleitung

CODELOCKS

CODELOCKS CL2000 Bedienungsanleitung

CODELOCKS

CODELOCKS CL6010 Bedienungsanleitung

CODELOCKS

CODELOCKS CL200 Bedienungsanleitung

CODELOCKS

CODELOCKS Pushbutton 500 Series Kurzanleitung

CODELOCKS

CODELOCKS CL4510 Bedienungsanleitung

CODELOCKS

CODELOCKS CL300 Bedienungsanleitung

CODELOCKS

CODELOCKS CL5000 Bedienungsanleitung

CODELOCKS

CODELOCKS KitLock Slam Latch Bedienungsanleitung

CODELOCKS

CODELOCKS CL4510 Bedienungsanleitung

CODELOCKS

CODELOCKS CL5510 Bedienungsanleitung

CODELOCKS

CODELOCKS CL210 Bedienungsanleitung

CODELOCKS

CODELOCKS CL500 Bedienungs- und Wartungsanleitung

CODELOCKS

CODELOCKS KL1000 G3 NetCode Bedienungsanleitung

CODELOCKS

CODELOCKS Kit-Lock KL1100 Bedienungsanleitung

CODELOCKS

CODELOCKS CL1000 Bedienungsanleitung

CODELOCKS

CODELOCKS CL4510 Bedienungsanleitung

CODELOCKS

CODELOCKS CL100 Bedienungsanleitung

CODELOCKS

CODELOCKS CL5500 SERIES Bedienungsanleitung

CODELOCKS

CODELOCKS CL400 Bedienungsanleitung

CODELOCKS

CODELOCKS CL50 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung