CODELOCKS CL250 Administratorhandbuch

CL250&CL250KEYCodeChangeGuide

The CL250 code chamber consist of 13 buttons from which the code is selected, and a ‘C’

button which is used to re-set the chamber after an incorrect entry, and which must always be

used as the first digit of a code. Buttons may only be used once in a code. For example, 1212

is not possible.

A CL250 code, or combination, can be entered in any order or sequence; e.g. 1234 can be

4321 or 1342 or whatever sequence is most convenient to remember. With 13 buttons, a total

of 8,191 different codes are available, any of which can be entered in any sequence.

Most people will set a code in the range of 4 to 7 digits, and the total number of codes in this

range is 5,434.

The lock is factory set with a randomly selected 6 digit code starting with the C button. The

code is not recorded by the factory. The code can be changed as often as required to any other

6 digit code. Every new code must start with the C button. Using the spare tumblers, one red

and one blue, the code length can be changed to 5 or 7 digits. Shorter codes are possible, but

1 or 2 digit codes are not recommended.

Code Change Instructions

1. Take your CL250 lock off the door by unscrewing the 2 bolts in the backplate.

2. Press the C button to reset the chamber and place the lock case on a flat surface with the

buttons down.

3. Remove the 2 red screws and carefully lift off the code chamber plate. Check that all 14

springs are held in place on the plate.

4. Note that the red tipped code tumblers correspond in position to the existing code. The blue

tipped non-code tumblers fill the other positions. The C tumbler is not coloured.

5. Hold the lock in your hand and depress the C button. Keeping the C button depressed use

tweezers to re-position the tumblers to correspond with your new code. The square notches of

ALL tumblers MUST face outwards, with the coloured tips ON TOP: see diagram below. Do

not force the tumblers in.

N.B. Holding the C button depressed whilst removing or replacing the tumblers is

essential to avoid damaging the internal mechanism. Do not attempt to reposition the C

tumbler.

6. Replace the code chamber plate carefully with the 2 red screws.

7. Check the operation of the new code, and make a written note of it before re-installing the

lock.

8. Insert the spindle, with the spring on the code side. On latchbolt locks, the spindle must

engage the latch as diagram below.

Maintenance

No maintenance of the working parts is necessary. Do not oil. To maintain the finish the lock

should be cleaned regularly with a soft cloth. A silicone spray or similar should be used to

provide a protective film against grit and grime.



Inhaltsverzeichnis

Andere CODELOCKS Sperren Handbücher

CODELOCKS

CODELOCKS CL5000 Bedienungsanleitung

CODELOCKS

CODELOCKS Kit-Lock KL1100 Bedienungsanleitung

CODELOCKS

CODELOCKS CL300 Bedienungsanleitung

CODELOCKS

CODELOCKS CL1000 Bedienungsanleitung

CODELOCKS

CODELOCKS CL1200 Bedienungsanleitung

CODELOCKS

CODELOCKS CL4510 Bedienungsanleitung

CODELOCKS

CODELOCKS CL255 Administratorhandbuch

CODELOCKS

CODELOCKS CL100 Bedienungsanleitung

CODELOCKS

CODELOCKS CL400 Bedienungsanleitung

CODELOCKS

CODELOCKS 4000 Series Bedienungsanleitung

CODELOCKS

CODELOCKS CL600 Bedienungsanleitung

CODELOCKS

CODELOCKS CL5500 SERIES Bedienungsanleitung

CODELOCKS

CODELOCKS CL5500 SERIES Bedienungsanleitung

CODELOCKS

CODELOCKS CL500 Bedienungsanleitung

CODELOCKS

CODELOCKS NANO90 Bedienungsanleitung

CODELOCKS

CODELOCKS KitLock Slam Latch Bedienungsanleitung

CODELOCKS

CODELOCKS CL5020 Bedienungsanleitung

CODELOCKS

CODELOCKS KL1050 C2 Bedienungsanleitung

CODELOCKS

CODELOCKS KL1000 G3 NetCode Bedienungsanleitung

CODELOCKS

CODELOCKS KL1050 Bedienungsanleitung

CODELOCKS

CODELOCKS CL50 Bedienungsanleitung

CODELOCKS

CODELOCKS Pushbutton 500 Series Kurzanleitung

CODELOCKS

CODELOCKS CL5510 Bedienungsanleitung

CODELOCKS

CODELOCKS CL210 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung