Cognex In-Sight D900 Series Bedienungsanleitung

In-Sight®D900 Series

Vision System

Manual

2020 October 20

Revision: 1.3.0.2

Regulations and Conformity

Note: For the most current CE declaration and regulatory conformity

information, see the Cognex support site: cognex.com/support.

Safety and Regulatory

Manufacturer Cognex Corporation

One Vision Drive

Natick, MA 01760 USA

In-Sight D902/D902C: Regulatory Model 50118

In-Sight D905/D905C: Regulatory Model R00099

This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take immediate measures. This

equipment complies with the essential requirements of the EU Directive 2014/30/EU.

Declarations are available from your local representative.

EU RoHS Compliant to the most recent applicable directive.

FCC FCC Part 15, Class A

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Korea In-Sight D902/D902C: Regulatory Model 50118: R-R-CGX-50118

In-Sight D905/D905C: Regulatory Model R00099: R-R-CGX-R00099

This device is certified for office use only and if used at home, there can be frequency

interference problems.

TÜV In-Sight D902/D902C: Regulatory Model 50118

In-Sight D905/D905C: Regulatory Model R00099

NRTL: TÜV SÜD AM SCC/NRTL OSHA Scheme for UL/CAN 61010-1.

CB report available upon request. TÜV SÜD AM, IEC/EN 61010-1.

China RoHS

Hazardous Substances 有害物质

Part Name

部件名称 Lead (Pb)

铅Mercury

(Hg)

汞

Cadmium

(Cd)

镉

Hexavalent

Chromium

(Cr (VI))

六价铬

Polybrominated

biphenyls (PBB)

多溴联苯

Polybrominated

diphenyl ethers

(PBDE)

多溴二苯醚

Regulatory

Model

50118

R00099

X O O O O O

This table is prepared in accordance with the provisions of SJ/T 11364.

这个标签是根据SJ / T 11364 的规定准备的。

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the

limit requirement of GB / T26572 - 2011.

表示本部件所有均质材料中含有的有害物质低于GB / T26572 - 2011 的限量要求。

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials used for this

part is above the limit requirement of GB / T26572 - 2011.

表示用于本部件的至少一种均质材料中所含的危害物质超过GB / T26572 - 2011 的限制要求。

For European Community Users

Cognex complies with Directive 2012/19/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment

(WEEE).

This product has required the extraction and use of natural resources for its

production. It may contain hazardous substances that could impact health and the

environment, if not properly disposed.

In order to avoid the dissemination of those substances in our environment and to

diminish the pressure on the natural resources, we encourage you to use the

appropriate take-back systems for product disposal. Those systems will reuse or

recycle most of the materials of the product you are disposing in a sound way.

The crossed out wheeled bin symbol informs you that the product should not

be disposed of along with municipal waste and invites you to use the appropriate

separate take-back systems for product disposal.

If you need more information on the collection, reuse, and recycling systems, please

contact your local or regional waste administration.

You may also contact your supplier for more information on the environmental

performance of this product.

Precautions

To reduce the risk of injury or equipment damage when you install the Cognex

product, observe the following precautions:

lThe vision system requires a UL or NRTL listed power supply with a 24VDC

output that meets the following rating requirements:

lAt least 5A continuous current.

lOutput rated SELV or National Electrical Code (NEC) Class 2.

Any other voltage creates a risk of fire or shock and can damage the

components. Applicable national and local wiring standards and rules must

be followed.

lThis product is intended for industrial use in automated manufacturing or

similar applications.

lThe safety of any system incorporating this product is the responsibility of

the assembler of the system.

lDo not install Cognex products where they are exposed to environmental

hazards such as excessive heat, dust, moisture, humidity, impact, vibration,

corrosive substances, flammable substances, or static electricity.

lRoute cables and wires away from high-current wiring or high-voltage

power sources to reduce the risk of damage or malfunction from the

following causes: over-voltage, line noise, electrostatic discharge (ESD),

power surges, or other irregularities in the power supply.

lDo not expose the image sensor to laser light. Image sensors can be

damaged by direct, or reflected, laser light. If your application requires laser

light that might strike the image sensor, use a lens filter at the corresponding

laser wavelength. For suggestions, contact your local integrator or

application engineer.

lThisproduct does not contain user-serviceable parts. Do not make

electrical or mechanical modifications to product components.

Unauthorized modifications can void your warranty.

lChanges or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

lInclude service loops with cable connections.

lEnsure that the cable bend radius begins at least six inches from the

connector. Cable shielding can be degraded or cables can be damaged or

wear out faster if a service loop or bend radius is tighter than 10X the cable

diameter.

lThisdevice should be used in accordance with the instructions in this

manual.

lAll specifications are for reference purposes only and can change without

notice.

Installation

Read thissection to learn how the vision system connectsto itsstandard

components and accessories. For a list of options and accessories, contact your

Cognex sales representative.

Installation procedures and specifications are presented in detailin the In-Sight ®

D900 Series Vision System Reference Guide, which is installed with In-Sight Vision

Suite software.

Note: Cables are sold separately.

CAUTION:All cable connectors are keyed to fit the connectors on the vision

system. Do not force the connections or damage may occur.

Install the C-Mount Lens and Cover

(COV-7000-CMNT or COV-7000-CMNT-EX)

Complete the following steps to install a C-Mount lens and cover to the vision system.

The C-Mount covers are optional accessories and required for IP67 protection.

Note:

lWhen using a C-Mount lens, the following restrictions apply:

lMaximum thread length is 5.25mm.

lThe C-Mount lens threads and body cannot protrude more

than 6.5mm in length into the vision system when screwed in

unless the diameter of the backlens is smaller than

14.75mm. If the C-Mount lens threads and body protrude

more than 6.5mm, you can add a spacer between the lens

and vision system. However, the spacer decreases the

working distance.

lIf using the COV-7000-CMNT cover, the maximum lens length is

41mm, the maximum lens body diameter is 36.5mm and the

maximum diameter including locking screws is 47mm.

lIf using the COV-7000-CMNT-EX cover, the maximum lens length is

62mm, the maximum lens body diameter is 36.5mm and the

maximum diameter including locking screws is 46.5mm.

1. Remove the rubber faceplate covering the image sensor window, if

present.

2. Remove the protective film covering the threaded lens opening, if present.

Andere Handbücher für In-Sight D900 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Cognex Bildverarbeitungssystem Handbücher

Cognex

Cognex In-Sight 8200 Bedienungsanleitung

Cognex

Cognex In-Sight 7000 Series Bedienungsanleitung

Cognex

Cognex In-Sight 7000 Gen2 Series Bedienungsanleitung

Cognex

Cognex In-Sight 7000 Gen2 Series Bedienungsanleitung

Cognex

Cognex In-Sight 9000 Series Bedienungsanleitung

Cognex

Cognex In-Sight 1700 Series Bedienungsanleitung

Cognex

Cognex In-Sight 2800 Series Bedienungsanleitung

Cognex

Cognex In-Sight 8405 Bedienungsanleitung

Cognex

Cognex In-Sight 5110 Bedienungsanleitung

Cognex

Cognex In-Sight 7800C Bedienungsanleitung

Cognex

Cognex n-Sight 7802 Bedienungsanleitung

Cognex

Cognex In-Sight 7000 Series Kurzanleitung

Cognex

Cognex In-Sight 2801 Bedienungsanleitung

Cognex

Cognex In-Sight 9902L Bedienungsanleitung

Cognex

Cognex In-Sight 8000 Series Bedienungsanleitung

Cognex

Cognex In-Sight D900 Series Bedienungsanleitung

Cognex

Cognex In-Sight 5000 Series Montage- und Bedienungsanleitung

Cognex

Cognex In-Sight 7000 Series Kurzanleitung

Cognex

Cognex In-Sight 8000 Series Bedienungsanleitung

Cognex

Cognex 9000 SerieIn-Sights Bedienungsanleitung

Cognex

Cognex In-Sight 3D-L4000 Series Bedienungsanleitung

Cognex

Cognex In-Sight 2000 Bedienungsanleitung

Cognex

Cognex In-Sight 9902L Bedienungsanleitung

Cognex

Cognex In-Sight 7000 Series Bedienungsanleitung

Beliebte Bildverarbeitungssystem Handbücher anderer Marken

Festo

Festo SBOC-M-R1B-H Bedienungsanleitung

Banner

Banner VE200G1B Bedienungsanleitung

SVS-Vistek

SVS-Vistek CoaxPress EoSens Creation 1.1CXP2 Bedienungsanleitung

Sony

Sony Vision Exchange PEQ-C100 Bedienungsanleitung

Datalogic

Datalogic MX-U81 Montageanleitung

Spektrum

Spektrum SPMVR2520 Bedienungsanleitung

Huaray

Huaray Movidius Series Bedienungsanleitung

Daheng Imaging

Daheng Imaging MERCURY2 USB3 Bedienungsanleitung

SVS-Vistek

SVS-Vistek exo174 U3 Series Bedienungsanleitung

Teledyne

Teledyne e2v Eliixa+ Series Bedienungsanleitung

Photron

Photron FASTCAM Mini CX Series Bedienungsanleitung

National Instruments

National Instruments Vision CVS-1455 Bedienungsanleitung

Omron

Omron FH-L550 Bedienungsanleitung

iGen

iGen NV20/20 Bedienungsanleitung

JAI

JAI GO-5100MP-USB Bedienungsanleitung

Ark Vision Systems

Ark Vision Systems AVS-Monitor 7 FHD Bedienungsanleitung

Feniex

Feniex C-5500 Bedienungsanleitung

SVS-Vistek

SVS-Vistek CoaXPress fxo540 Bedienungsanleitung