Colortrac SmartLF Cx Series Bedienungsanleitung
Cx+40IM
Colortrac Ltd
Page 1 of 12
Version 3
Cx(+)40 Main Board Instructions
Date:02/08/12
This is a confidential controlled document and is the property of Colortrac Ltd.
It is not to be copied or reproduced in part or whole. It is intended for staff to read.
S
Sm
ma
ar
rt
tL
LF
F
C
Cx
x
/
/
C
Cx
x+
+4
40
0
S
Sc
ca
an
nn
ne
er
rs
s
P
P0
00
02
20
04
41
1A
A
M
Ma
ai
in
n
B
Bo
oa
ar
rd
d
F
FR
RU
U
V
V3
3
NOTE:
PLEASE READ THESE INSTRUCTIONS FOR INSTALLATION OF THE BOARD.
SmartLF Cx+40 Instruction Manual
Page 2 of 12
SmartLF Cx(+)40 Scanner
Cx(+)40m, Cx(+)40c & Cx(+)40e
Main Board Instruction Manual
Issue 3
©Colortrac Ltd 2012
The product and the contents of this publication may be changed without prior notification.
Colortrac Ltd makes every effort to ensure this publication is free from errors. Misprints, errors
or quality observations should be reported to Technical Support, Colortrac Ltd.
Colortrac Ltd shall not be liable for any damages, errors, issues or events that result from the
use of the equipment or this manual.
No part of this product or publication may be reproduced,
copied or transmitted in any form or by any means without
permission from:
International Technical Support Manager
Colortrac Ltd.
3 –5 Brunel Court.
Burrel Road.
St Ives,
Huntingdon,
Cambridgeshire,
PE27 3LW.
United Kingdom.
Tel: +44 (0)1480 464618
Fax: +44 (0)1480 464620
www.colortrac.com
SmartLF Cx+40 Instruction Manual
Page 3 of 12
Content
1Main Board ................................................................................................................................................. 4
1.1 Tools Required................................................................................................................................... 4
1.2 Opening Access Panel....................................................................................................................... 4
1.3 Removing / Replacing The Main Board............................................................................................. 6
2Utilities Program ......................................................................................................................................... 9
2.1 Normalisation..................................................................................................................................... 9
2.2 Firmware / Driver Installation........................................................................................................... 10
2.3 Save .dat File................................................................................................................................... 11
2.4 Cx(+)40 Restore Program................................................................................................................ 12
SmartLF Cx+40 Instruction Manual
Page 4 of 12
1 Main Board
1.1 Tools Required.
To work on the SmartLF scanners, certain tools will be required. See list below. The acquisition of
these tools is strongly recommended.
1. Medium Pozi-drive screwdriver
2. Flat Screwdriver
3. 7mm Nut Spinner.
4. 5.5mm Nut-spinner.
5. 1.5mm Allen Key
6. 2mm Allen Key
7. 2.5mm Allen Key
8. Cleaning fluid
9. Lint free wipes
1.2 Opening Access Panel.
1.2.1 Safety Precautions
Ensure that the power is completely disconnected from the scanner unit.
Ensure the scanner is positioned on its Colortrac stand, or a stable maintenance platform.
1.2.2 IMPORTANT NOTE
Before removing the Main Board, open the utilities program (while the scanner is powered
up) and save a dat file as described in chapter “2.3 Save .dat File” page 11. Or record the
Stitch Values, Motor Speed and X Resolution values by using the Utilities Program page
9. If the scanner is not functioning do save the dat file, please contact Colortrac Support
for the original dat file.
1.2.3 Tools
Medium pozi-drive screwdriver.
1.2.4 Procedure
1. Unplug mains lead and USB
Connector.
SmartLF Cx+40 Instruction Manual
Page 5 of 12
2. Remove the 8 x M3 Pan Head
screws holding the rear panel
in place. Make sure you are
holding the panel up as you
remove the last screw.
3. Gently lower the panel down.
The panel is hinged so will not
need to be totally removed.
4. Make sure that none of the
cables are being pulled tight or
have caught on anything while
in the lowered position.
SmartLF Cx+40 Instruction Manual
Page 6 of 12
1.3 Removing / Replacing The Main Board.
1. Open rear access panel as
described in chapter “1.2
Opening Access Panel.” page
4.
2. Disconnect CIS ribbon cables
by first, carefully, releasing the
locking slide and then sliding
the cable out from the
connector and out through the
ferrite held on the panel.
Repeat this to all 5 ribbon
cables.
3. Disconnect the power Cable
PSU DC O/P from PSU and the
motor cable.
4. Disconnect the display board
ribbon cable from the Main
board.
SmartLF Cx+40 Instruction Manual
Page 7 of 12
5. Remove the ten M3 x 10mm
screws and the two M4 x 6mm
screws that hold the Main
board on to the panel and
gently remove from scanner.
6. Hold the replacement board up
to the panel and insert the first
M3 x 10 screw in the central
hole at the top of the board to
hold it in place, do not tighten
at this point.
7. Insert the two M4 x 6mm
screws into the holes either
side of the USB2 connector.
Then insert the remaining nine
M3 x 5mm screws around the
board, when all are in place,
tighten all the screws up,
making sure not to apply too
much pressure.
SmartLF Cx+40 Instruction Manual
Page 8 of 12
8. Make sure the locking sliders
on the CIS connectors are lifted
up to allow the cable to be
inserted.
9. Making sure the cables are
inserted the correct way
around, insert all 5 of the CIS
ribbon cables into their
adjacent connectors. The
exposed ribbon cores must
face towards the access panel,
so therefore you will see the
blue backing. This is true for
ALL 5 ribbon cables.
10. Re-insert the power Cable PSU
DC O/P from PSU, motor drive
cable and display board ribbon
cable making sure they are
located and positioned
correctly.
11. Close the rear access panel as
described in chapter “1.2
Opening Access Panel.” page
4.
After fitting the main board, load the dat file that had been saved earlier as described in chapter “0
in chapter “0
1.4 Cx(+)40 Restore Program
12. ” page 12. Or load the dat file send by Colortrac Support. Update the firmware to the
latest as described on page 10, and then run the Normalisation program (page 9) after
all processes are complete.
SmartLF Cx+40 Instruction Manual
Page 9 of 12
2 Utilities Program
2.1 Normalisation.
1. Insert the white calibration
target supplied with the
scanner matt side faced down.
2. Click the ‘Full Normalisation’
button and allow it to run. This
takes about 5 minutes, and the
target will move through the
scanner during this time.
Remove the target when
completed.
NOTE: This calibration target is supplied with the scanner and should have a width of 103cm, if
the target is missing/damaged, any good quality large format paper can be used making sure it is
cut to 103 x 50cm
SmartLF Cx+40 Instruction Manual
Page 10 of 12
2.2 Firmware / Driver Installation.
To install the firmware manually, firstly save the latest firmware .cab file (making sure that
it is for the Cx+ 40 scanner) which contains the latest firmware on to the PC attached to
the scanner, this can be downloaded from:
http://www.colortrac.com/support/support_downloads.htm
1. Click ‘Install New Firmware’
NOTE: ‘Install New Windows
Driver’ no longer works from the
utilities program, due to changes in
the Microsoft operating systems,
install new drivers in the normal
way through the Device Manager.
2. Click the ‘Install New Firmware’
button and locate the file you
just saved, this will then install
to the scanner.
3. Power down the scanner and
software, and reboot scanner.
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Colortrac Scanner Handbücher
Colortrac
Colortrac SmartLF Cx 40C Bedienungsanleitung
Colortrac
Colortrac SmartLFGx+ 28 Montageanleitung
Colortrac
Colortrac SmartLF Ci 40E Montageanleitung
Colortrac
Colortrac SmartLF 4080E Handbuch
Colortrac
Colortrac SmartLF SG Bedienungsanleitung
Colortrac
Colortrac 3 Series Bedienungsanleitung
Colortrac
Colortrac SmartLF Scan! 24 Bedienungsanleitung
Colortrac
Colortrac SmartLF Ci24m Bedienungsanleitung
Colortrac
Colortrac SMARTLF SCAN Bedienungsanleitung
Colortrac
Colortrac 5480e Bedienungsanleitung
Colortrac
Colortrac SmartLF Gx25m Bedienungsanleitung
Colortrac
Colortrac SMARTLF SCAN Bedienungsanleitung
Colortrac
Colortrac L24 Bedienungsanleitung
Colortrac
Colortrac SmartLF SG Series Bedienungsanleitung
Colortrac
Colortrac T Series Bedienungsanleitung
Colortrac
Colortrac SMARTLF SCAN Bedienungsanleitung
Colortrac
Colortrac SmartLF SC25m Bedienungsanleitung
Colortrac
Colortrac UC56T Bedienungsanleitung
Colortrac
Colortrac SMARTLF SCAN Bedienungsanleitung
Colortrac
Colortrac SmartLF Cx 40M Bedienungsanleitung
