Comax CM-PIR03 Bedienungsanleitung
Introduction
Thanks for choosing the Comax’s
wireless PIR motion sensor
Wave
TM
enabled device (interoperable, two
Z-Wave
TM
enabled network. Every
main
devices result in more possible transmissi
Z-Wave
TM
enabled device displaying the Z
and ours can also be used in other manufacturer’s Z
and send Z-Wave
TM
signal when movement is detected inside the building
Product Description
Specification:
Protocol: Z-
Wave
Frequency Range:
Operating Range: Up to 50M
Operating Temp.:
Battery: CR123A
Installation
1. Open the cover and i
nsert battery into the battery compartment, LED will start to flash slowly.
2. Close the back cover.
To add the sensor, Put the Z-
Wave
CM-PIR03 to your controller
. Press the program switch of
stop flashing, if not, please try again.
To Delete the sensor
from network,
instruction to delete the CM-
PIR03
deleted. The LED on the
sensor
3. Mount the sensor
at 2 meters above surface. To enhance proper operation, place
can detect the room widely.
Operation Manual
Wireless PIR Motion Sensor
CM-PIR03
wireless PIR motion sensor
for
the home security device. This sensor is a Z
enabled device (interoperable, two
-
way RF mesh networking technology) and is fully compatible with any
main
powered Z-Wave
TM
enabled device acts as a signal repeater and multiple
devices result in more possible transmissi
on routes which helps eliminate “RF dead-spots”.
enabled device displaying the Z
-Wave
TM
logo can also be used with it regardless of the manufacturer,
and ours can also be used in other manufacturer’s Z
-Wave
TM
enabled networks. This sensor mon
signal when movement is detected inside the building
.
Wave
Frequency Range:
868.4MHz
,
865.2MHz
Operating Range: Up to 50M
line of sight
Operating Temp.:
-10°C to 50°C
Battery: CR123A
-1pcs
nsert battery into the battery compartment, LED will start to flash slowly.
Wave
Interface Controller into “add” mode, and follow
instruction
. Press the program switch of
CM-PIR03
once. The LED on the
stop flashing, if not, please try again.
from network,
Put the Z-Wave Interface Controller into “
delete” mode, and follow
PIR03
to your controller. Press the program switch of
sensor
sensor
should start to flash.
at 2 meters above surface. To enhance proper operation, place
sensor
the home security device. This sensor is a Z
-
way RF mesh networking technology) and is fully compatible with any
enabled device acts as a signal repeater and multiple
logo can also be used with it regardless of the manufacturer,
enabled networks. This sensor mon
itors movement,
nsert battery into the battery compartment, LED will start to flash slowly.
instruction
to add the
once. The LED on the
sensor should
delete” mode, and follow
sensor
once to be
on the angle which
Operation
1. Walk in front of sensor
, sensor will send the st
2. If
no movement detected in three minutes after sent status of “ON”, the sensor will send the
3.
Normal operation, the LED will not light.
4. The CM-PIR03
sensor equipped with tamper switch. If the cover of sensor is removed, the PIR sensor will
send an alarm report to the Z-
Wave
Warranty terms
Comax Guarantees that every PIR
sensor
for one year from the date of purchase. If the product proves defective during this one
will replace it free of charge.
Note:
This warranty does not apply
•
Damage to units caused by accident, dropping or abuse in handling, or any negligent use.
•
Units which have been subject to unauthorized repair, taken apart, or otherwise modified
•
Units not used in accordance with instruction
•
Damages exceeding the cost o
•
Transit damage, initial installation costs, removal cost, or reinstallation cost.
, sensor will send the st
atus of “ON” and the LED will flash once.
no movement detected in three minutes after sent status of “ON”, the sensor will send the
Normal operation, the LED will not light.
sensor equipped with tamper switch. If the cover of sensor is removed, the PIR sensor will
Wave
Interface Controller, and the LED will go solid.
sensor
is
free from physical defects in material and workmanship under normal use
for one year from the date of purchase. If the product proves defective during this one
-
year warranty period, Comax
This warranty does not apply
to
Damage to units caused by accident, dropping or abuse in handling, or any negligent use.
Units which have been subject to unauthorized repair, taken apart, or otherwise modified
Units not used in accordance with instruction
Damages exceeding the cost o
f the product
Transit damage, initial installation costs, removal cost, or reinstallation cost.
status of “OFF”
sensor equipped with tamper switch. If the cover of sensor is removed, the PIR sensor will
free from physical defects in material and workmanship under normal use
year warranty period, Comax
Damage to units caused by accident, dropping or abuse in handling, or any negligent use.
Units which have been subject to unauthorized repair, taken apart, or otherwise modified
Inhaltsverzeichnis
Andere Comax Zubehör Handbücher
