CommScope BUDI-S Bedienungsanleitung

BUDI-S

INSTALLATION INSTRUCTION

Building distributor

• Box

• Base tray

• Base tower

• Termination units

• Inserts for SMOUV and ANT

Accessories

Introduction

Suitable for FTTH applications where easily pre-connectorized splitters

modules can be build in. The box is designed In such a way that it is

suitable for both spliced and connectorized solutions of the riser cable.

Kit content

• Tray kit

Seals

Wrap around cable seals

Sealblock 4 x 10 mm

Cable diameter (mm) Foam (± 5 mm)

3 95

4 90

5 80

6 75

7 70

8 60

9 50

10 40

Sealblock 4 x 15 mm

Cable diameter (mm) Foam (± 5 mm)

9 125

10 115

11 105

12 95

13 85

14 70

15 60

Sealblock 2 x 20 mm

Cable diameter (mm) Foam (± 5 mm)

14 155

15 140

16 125

17 110

18 95

19 85

20 75

Sealblock 24 x 8 mm

Cable range 1.8 – 7 mm

Sealblock rubber 1 x 18

To use in ports S4-S5 only

Cable range 3 – 8 mm

Standard seals

PG 16

PG 21

PG 29

PG 29 (PTS 24)

TC-906-S-IP

Rev A, Mar 2017

www.commscope.com

1.3 Different wrap-around ports are available (including brackets).

Use two guiding pins to open the ports and to secure the bottom part to

the box.

1.4 Install the cable bracket depending the cable seal.

1.1 Make a cut on both sides of the port to open the port.

1 Preparation of the box

1.2 Use a plier to break-out the port, starting from front to back.

Remove all the burrs.

S1 S2 S3

2.1 Mark the loose tube at the position of the tray.

2.2 1: Storage area (dark ﬁbers)

2: Splicing to splitter modules

3: Point to point applications

1.5 Use a hacksaw to reach the onion rings, which can be opened

with a plier to open the in-line ports (S4/S5).

1.6 Install the wrap-around rubber seal into the port.

2 Base tray

2.3 Route the ﬁbers to the different areas (1-2-3).

S4 S5

2.4 Store the ﬁbers which will be used later.

2.5 Store the ﬁbers which will be spliced day 1 to the splitter

modules.

2.6 Store the ﬁbers which will be spliced day 1 for the point-to-

point applications.

3 Drop cables (point-to-point applications)

3.1 Remove the outer jacket over a distance of 1.2 m.

3.2 Wrap one layer of foam (20 mm) on the securing position if

needed. Terminate the aramid strength member by securing the cable/

pigtail onto thebracket with tie-wrap. Depending the amount of aramid

strength member, it needs to be wrapped twice around the bracket.

3.3 Install the terminated drop cable in the numbered ports on the

base tray.

3.4 Splice the ﬁbers from the drop cable to the ﬁbers from the

looped cable. In case of SMOUV, use the insert.

3.5 Install the cover onto the tray.

Slide

Click

4.1 Install the patch tray onto the tower.

4.2 Insert the adaptor into the designated positions.

4 Patching tray

4.3 Install the cable into the port and secure with hook and loop

fastener tape onto the bracket and seal with foam (see length page 1).

Mini –PICO (no connectors)

4.4 Close the port.

4.5 Install the foam at the position on the patch tray and secure

with 2 tie-wraps as shown on the picture.

4.6 Install the splice holders onto the patch tray.

4.7 Splice the MINI PICO ﬁbers to the pigtails and store the

overlength in the splice area. Check the orientation of both ﬁbers to

avoid crossings.

Foam

Hook and loop

fastener

Hook and loop

fastener

4.8 Install the cover onto the tray.

Mini PICO (pre-connectorized)

4.10 Connect the mini PICO cable with the designated adaptors

and store the overlength in the splice area.

4.9 In case of pre-connectorized MINI PICO cable, ﬁbers are also

routed behind the tower and secured with foam and tie-wraps onto the

tray.

4.11 Install the cover onto the tray.

Click

Slide

Click

4.13 2 parking places for pigtails from splitter which are not used

day 1 can be installed.

4.12 Secure the patch trays with the rubber ﬂex part, as shown.

5.3 Install the splitter into the holder.

5.5 Install the incoming pigtail and route the ﬁber to the splicing to

“splicing to splitter modules” for splicing. Remove the outer jacket over a

distance of 1.2 m. Secure with foam and tie-wrap.

5.4 Route the pigtails to the designated adapters on the patch tray.

Bundle the pigtails with hook and loop fastener when needed.

5.2 Install the bend control and splitter holder into the box.

5 Splitters

OCM6 in-line

5.1 Install the adapter in the splitter holder.

OCM6 butt

5.7 Route the incoming pigtails of the splitter (marked with red

ﬂag) to the base tray and remove the outer jacket from the mark over a

distance of 1.2 m. Secure with foam and tie-wrap onto the base tray.

5.6 Install the splitter into the holder and route the pigtails via the

bend control.

5.8 Install the splice holders onto the patch tray.

5.9 Splice the MINI PICO ﬁbers to the pigtails and store the

overlength in the splice area. Check the orientation of both ﬁbers to

avoid crossings.

Slide Click

6 Closing the box

6.1 Close the box.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CommScope Kabel und Steckverbinder Handbücher

CommScope

CommScope FDH1204-24SE2 Bedienungsanleitung

CommScope

CommScope SYSTIMAX 360 iPatch 360-iP-G2-1U-LC-FX Bedienungsanleitung

CommScope

CommScope SYSTIMAX VisiPatch CPC5562 Bedienungsanleitung

CommScope

CommScope NOVUX Bedienungsanleitung

CommScope

CommScope OFDC-A4 SPLICE/PATCH Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HTC1006 Series Merkblatt

CommScope

CommScope SYSTIMAX 360 iPatch PATCHMAX Bedienungsanleitung

CommScope

CommScope HELIAX MFJS6UDHNA00 Bedienungsanleitung

CommScope

CommScope FIST-RSKG-16 Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HFA208 Series Merkblatt

CommScope

CommScope OmniReach FTTX Bedienungsanleitung

CommScope

CommScope FOSC-450D Bedienungsanleitung

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope FOSC-350C Bedienungsanleitung

CommScope

CommScope FIST-RSKG-1 Bedienungsanleitung

CommScope

CommScope FIBER INDEXING TERMINAL Bedienungsanleitung

CommScope

CommScope FD21206-48SRC Series Merkblatt

CommScope

CommScope FACT Bedienungsanleitung

CommScope

CommScope SYSTIMAX 360 iPatch... Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HFT1206-24S49 Series Merkblatt

CommScope

CommScope FOSC-400BG Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT 1933352 Series Bedienungsanleitung

CommScope

CommScope FOSC 450 A Bedienungsanleitung

CommScope

CommScope OSP-CLPFEC-LG Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung