CommScope HELIAX FiberFeed HFA208 Series Merkblatt

www.commscope.com/andrew • 1-800-255-1479 Bulletin # 7695778 Rev. E 1

Technical Publication

Related Support and Learning Opportunities Offered by the CommScope Infrastructure Academy

The insights and expertise contained in this manual represent just one small part of CommScope

global learning initiative. Few industries are evolving as quickly as wireless communications. Every

technological innovation impacts what happens in the field. Our customers look to the CommScope

Infrastructure Academy to make sure their technicians and installers are well trained, well-prepared,

and well-educated to take advantage of opportunities as they evolve.

Field Engineering Services (FES)

Support services, such as our Field Engineering Services (FES) Group gives customers access to

technical support where and when it is needed the most — in the field. The FES team is staffed

by an expert team of technicians who, in turn, are supported by some of the brightest and most

experienced product line managers. With all of this knowledge and support the FES offers our

customers access to hands-on, specialized training classes.

Section 1: General Specifications .....................................................……………………………………..………02

Section 2: Breakout Procedure / DLC Connection Considerations .....……………………………………....04

Section 3: Cleaning / Inspecting ....……………………..…………………………………………………………....05

Section 4: Excess Cable Handling .......................................................……………….……………………..……06

Section 5: Hanger / Jacketing Removal / Grounding .............................................................………………..07

Section 6: Protecting Spare Fibers / Installation Check List ........................................……………….......…....08

Customer Service Center

United States and Mexico 1-800-255-1479 or 1-888-235-5732

International: +1-779-435-8579

Installation Guidelines – HELIAX®FiberFeed®Rooftop Solution

Fiber/Copper Hybrid Cables: HFA208 │HFA210 │HFA406

www.commscope.com/andrew • 1-800-255-1479 Bulletin # 7695778 Rev. E 2

Technical Publication

General Specifications

Cable Type

Center Conductor Gauge

Conductors, quantity

Total Fiber Quantity

Armor Type

Fiber Type

Dimensions

Cable Weight

Diameter Over Jacket

Breakout Length, Fiber, end 1

Breakout Length, Power, end 1

Breakout Length, Fiber, end 2

Breakout Length, Power, end 2

Physical Specifications

Minimum Bend Radius, loaded

Minimum Bend Radius, unloaded

Tensile Load, long term, maximum

Tensile Load, short term, maximum

HFA208-6MT2-XXX

8 AWG

Corrugated aluminum

Multimode

.43 kg/m | .29 lb/ft

20.0 mm | 0.79 in

1000 mm | 39.37 in

399.0 mm | 15.7 in

200.0 mm | 7.9 in

534 N | 120 lbf

1780 N | 400 lbf

HFA208-6MT3-XXX

8 AWG

Corrugated aluminum

Multimode

.43 kg/m | .29 lb/ft

20.0 mm | 0.79 in

1000 mm | 39.37 in

399.0 mm | 15.7 in

200.0 mm | 7.9 in

534 N | 120 lbf

1780 N | 400 lbf

General Specifications

Cable Type

Center Conductor Gauge

Conductors, quantity

Total Fiber Quantity

Armor Type

Fiber Type

Dimensions

Cable Weight

Diameter Over Jacket

Breakout Length, Fiber, end 1

Breakout Length, Power, end 1

Breakout Length, Fiber, end 2

Breakout Length, Power, end 2

Physical Specifications

Minimum Bend Radius, loaded

Minimum Bend Radius, unloaded

Tensile Load, long term, maximum

Tensile Load, short term, maximum

HFA208-6MC1-XXX

8 AWG

Corrugated aluminum

Multimode

.43 kg/m | .29 lb/ft

20.0 mm | 0.79 in

1000 mm | 39.37 in

399.0 mm | 15.7 in

200.0 mm | 7.9 in

534 N | 120 lbf

1780 N | 400 lbf

HFA208-6SC2-XXX

8 AWG

Corrugated aluminum

Single mode

.43 kg/m | .29 lb/ft

20.0 mm | 0.79 in

1000 mm | 39.37 in

399.0 mm | 15.7 in

200.0 mm | 7.9 in

534 N | 120 lbf

1780 N | 400 lbf

HFA208-8SC2-XXX

8 AWG

Corrugated aluminum

Single mode

.43 kg/m | .29 lb/ft

20.0 mm | 0.79 in

1000 mm | 39.37 in

2000 mm | 78.74 in

399.0 mm | 15.7 in

200.0 mm | 7.9 in

534 N | 120 lbf

1780 N | 400 lbf

HFA210-6SC2-XXX

10 AWG

Corrugated aluminum

Single mode

.30 kg/m | .20 lb/ft

16.69 mm | 0.66 in

1000 mm | 39.37 in

2000 mm | 78.74 in

334.0 mm | 13.1 in

200.0 mm | 7.9 in

810 N | 180 lbf

2700 N | 600 lbf

www.commscope.com/andrew • 1-800-255-1479 Bulletin # 7695778 Rev. E 3

Technical Publication

General Specifications

Cable Type

Center Conductor Gauge

Conductors, quantity

Total Fiber Quantity

Armor Type

Fiber Type

Dimensions

Cable Weight

Diameter Over Jacket

Breakout Length, Fiber, end 1

Breakout Length, Power, end 1

Breakout Length, Fiber, end 2

Breakout Length, Power, end 2

Physical Specifications

Minimum Bend Radius, loaded

Minimum Bend Radius, unloaded

Tensile Load, long term, maximum

Tensile Load, short term, maximum

HFA406-8MT1-XXX

6 AWG

Corrugated aluminum

Multimode

.80 kg/m | .54 lb/ft

22.6 mm | 0.89 in

1000 mm | 39.37 in

451.0 mm | 17.8 in

226.0 mm | 8.9 in

1070 N | 240 lbf

3560 N | 800 lbf

HFA406-8MT2-XXX

6 AWG

Corrugated aluminum

Multimode

.80 kg/m | .54 lb/ft

22.6 mm | 0.89 in

2000 mm | 78 in

5000 mm | 196.85 in

451.0 mm | 17.8 in

226.0 mm | 8.9 in

1070 N | 240 lbf

3560 N | 800 lbf

HFA406-8MT3-XXX

6 AWG

Corrugated aluminum

Multimode

.80 kg/m | .54 lb/ft

22.6 mm | 0.89 in

2000 mm | 78 in

5000 mm | 196.85 in

451.0 mm | 17.8 in

226.0 mm | 8.9 in

1070 N | 240 lbf

3560 N | 800 lbf

www.commscope.com/andrew • 1-800-255-1479 Bulletin # 7695778 Rev. E 4

Technical Publication

LC Connectors and Adapter cleaning

Clean exposed connector ferrule by lightly moistening lint-free wipe with ber optic cleaning solution (or >91%

isopropyl alcohol), and by applying medium pressure, rst wipe against wet area and then onto dry area to clean

potential residue from end face. Clean connector ferrule inside adapter by inserting lightly moistened cleaning stick

with ber optic cleaning solution (or >91% isopropyl alcohol) inside the adapter until contact is made with connector on

opposite end. Rotate cleaning stick with medium pressure in one circular motion as it is pulled away from the adapter.

Repeat process using dry cleaning stick.

Caution: Signal strength will be affected if end and sides of ferrule are not thoroughly cleaned. Discard cleaning

sticks after each use. Do not turn cleaning sticks back and forth pressing against connector end face. This may cause

scratches if large contamination is present. Always inspect connector end face for contamination after each cleaning.

Clean adapter by inserting adapter cleaning stick (or fiber adapter sleeve brush) moistened with fiber optic cleaning

solution (or >91% isopropyl alcohol) inside the adapter and gently pull out with twisting motion. Repeat process with a

dry cleaning stick.

Caution: Do not try to clean adapter with a standard pipe cleaner. The sleeve inner diameter of LC adapters is too

small. Do not try to clean the adapter with cleaning stick if a connector is mounted in one side. Discard cleaning sticks

after each use.

Clean Tip of Ferrule

Clean Sides of Ferrule

Adapter Brush

Breakout Procedure

Remove electrical tape from the trunk

cable and corrugated protection tube.

While holding the protection tube straight

pull the tube away from cable.

After you have pulled the ber and power

conductors into the OVP box remove electrical

tape from the trunk cable and remove clear tube

for access to all optical connectors.

After the trunk cable has been installed and you are ready to make the nal connection follow these steps for the

removal of ber protection tube.

www.commscope.com/andrew • 1-800-255-1479 Bulletin # 7695778 Rev. E 5

Technical Publication

Device designed for cleaning the ferrule end faces of LC connectors

Open guide cap, insert LC connector into guide, push the outer shell to start cleaning the LC connector interface, a

"click" sound indicates end of a cleaning process, repeat, close cap immediately after use.

Caution: Be careful not to slant LC connector while inserting into the Guide cap. Do not overly exert force during

insertion as this may cause damage to both the connector and the cleaner.

All in one cleaner

Guide

LC Connector

Push Cleaner X2

Cap

Part Number: FCCT - L

There are 3 basic principles that are critical to achieving an efficient fiber optic connection:

1. Perfect Core Alignment

2. Physical Contact

3. Pristine Connector Interface

Today’s connector design and production techniques have eliminated most of the challenges to achieving

core alignment and physical contact. What remains challenging is maintaining a pristine end-face. As a result,

CONTAMINATION is the #1 reason for troubleshooting optical networks.

Implementing the process of cleaning and inspecting before mating can reduce the time spent troubleshooting,

optimize signal performance and prevent damage.

Inspecting

Is It

Clean?

No Connect

Yes

Inspect

Clean

Abrasive particles (i.e. rock dust) can

cause permanent damage to the

interface. If interface is scratched it cannot

be repaired, it would need to be replaced.

www.commscope.com/andrew • 1-800-255-1479 Bulletin # 7695778 Rev. E 6

Technical Publication

Excess Cable Management

If length of cable installed needs to be adjusted you can split the cable at the BBU end using the process below and

then coiling the excess fiber subunits in a storage box. Fiber management trays are available to manage any excess

fiber length in the breakouts at the BBU.

1. Mark cutback length 2. Notch armor using flush cutter in-line with Kevlar

strings

3. Place rip cord in notches 4. Pull rip cord parallel to cable (while supporting

breakout)

5. Stop at length marker 6. Separate armor

7. Cut armor using side cutter 8. Remove water blocking tape

9. Remove excess rip cord 10. Apply electrical tape to protect breakout

Excess Fiber

storage Box

Part Number:

FE-14126-E

Fiber management

tray, Part Number:

Fe-14192-IR

NOTE:

Remember to slide

identifier labels

down the power

conductors before

trimming the cable

to it’s final length

Scan to

view video

Cable Splitter tool

Part Number:

FA-RCRT-PD

www.commscope.com/andrew • 1-800-255-1479 Bulletin # 7695778 Rev. E 7

Technical Publication

Jacketing Removal Procedure for Grounding Kit Installation

• 1 Hanger required every 1 m (3 ft) of vertical cable

FA-1923-STH Style Hangers for HFT208 and HFT406 series cables

Ground kits required at the top and bottom before entering the equipment / shelter / cabinet

Ground Kit UG12158-15B4-T is a universal solution for all HFF trunk cables.

Only use Tin Plated grounding kits

1. Score the jacketing 360º

2. Measure 51 mm (2 in) and repeat

3. Identify where the aluminum shielding overlaps, this will feel like a flat spot in the cable

4. Remove a section of jacketing between score marks

5. Lift edge of jacketing

6. Grab lifted edge of jacketing with a pair of pliers and roll on the cable

7. Remove excess adhesive with a piece of emery cloth

www.commscope.com/andrew • 1-800-255-1479 Bulletin # 7695778 Rev. E 8

Technical Publication

Notice: CommScope disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.

Aviso: CommScope no acepta ninguna obligación ni responsabilidad como resultado de prácticas incorrectas o peligrosas de instalación, inspección, mantenimiento o retiro.

Avis : CommScope décline toute responsabilité pour les conséquences de procédures d’installation, d’inspection, d’entretien ou de retrait incorrectes ou dangereuses.

Hinweis: CommScope lehnt jede Haftung oder Verantwortung für Schäden ab, die aufgrund unsachgemäßer Installation, Überprüfung, Wartung oder Demontage auftreten.

Atenção: A CommScope abdica do direito de toda responsabilidade pelos resultados de práticas inadequadas e sem segurança de instalação, inspeção, manutenção ou remoção.

Avvertenza: CommScope declina eventuali responsabilità derivanti dell’esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.

CommScope

1100 CommScope Place SE P.O. Box 339, Hickory, NC 28603-0339

(828) 324-2200 (800) 982-1708

www.commscope.com/andrew

Customer Service 24 hours

North America: +1-800-255-1479 (toll free)

Any country: +1-779-435-6500

email: [email protected]

Jumpers are properly supported to prevent strain on fiber during severe weather

Bend radius minimums haven't been exceeded

CommScope FiberFeed®approved installation accessories are used

Maximum hanger spacing of 0.9 m (3 ft) - 1.2 m (4 ft) is maintained

Visually inspected end face for residual dirt and damage

Avoid migration of contaminations from one connector to another

Check continuity by using LED or laser light source from one end face and look for light from other end to

identify any broken fiber (Do not look directly at cable with laser source)

Fiber Connections are engaged and the sectors are consistent with requirements

Cable serial number has been documented in the closeout paperwork and a copy has been left on-site

Installation Check List

Protecting Spare Fibers

Slide the protection sleeve back over

the dark fiber ends to protect them.

Place tape over fiber tails and

protective sleeve end to hold in

place. Support protection sleeve

using tie wraps.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CommScope Kabel und Steckverbinder Handbücher

CommScope

CommScope FOSC-450D Bedienungsanleitung

CommScope

CommScope 760230938 Bedienungsanleitung

CommScope

CommScope FIBER INDEXING TERMINAL Bedienungsanleitung

CommScope

CommScope FOSC-400BG Bedienungsanleitung

CommScope

CommScope NOVUX SEC 100 Bedienungsanleitung

CommScope

CommScope FIST-RSKG-1 Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HFT1206-24S49 Series Merkblatt

CommScope

CommScope AMP NETCONNECT SL Series Bedienungsanleitung

CommScope

CommScope FOSC-350C Bedienungsanleitung

CommScope

CommScope PICABOND 60944-6 Bedienungsanleitung

CommScope

CommScope FACT Bedienungsanleitung

CommScope

CommScope LightCrimp Plus SC Simplex Bedienungsanleitung

CommScope

CommScope NOVUX SXT Bedienungsanleitung

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope HELIAX FiberFeed HFE810 Series Merkblatt

CommScope

CommScope LSX-288 Bedienungsanleitung

CommScope

CommScope SYSTIMAX 360 iPatch... Bedienungsanleitung

CommScope

CommScope QWIK MPO Series Bedienungsanleitung

CommScope

CommScope OFDC-A4 SPLICE/PATCH Bedienungsanleitung

CommScope

CommScope SYSTIMAX 360 iPatch 360-iP-G2-1U-LC-FX Bedienungsanleitung

CommScope

CommScope M2400 Series Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT MRJ21 1479452-1 Bedienungsanleitung

CommScope

CommScope FOSC450 C Bedienungsanleitung

CommScope

CommScope FDH1204-24SE2 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung