CommScope SYSTIMAX 360 iPatch G2 MPO Bedienungsanleitung

860538982

Issue 6, June 2014

www.commscope.com

SYSTIMAX 360™iPatch®G2 Fiber Sliding Shelf,

MPO Distribution Panel Instructions

Page 1 of 9

General

The SYSTIMAX 360™360G2 shelf comes equipped with iPatch® MPO kits, jumper-storage trough, and

polycarbonate top cover. This sliding distribution shelf includes iPatch MPO kits designed for use in an iPatch

System and MPO adapters that allow connection of multi-fiber trunk cables terminated with push-on MPO

connectors.

These shelves mount in a standard 19-inch (483mm) rack with universal hole spacing. These shelves are

intended for indoor use, but may be used outdoors in a suitable enclosure.

Note: To use the SYSTIMAX 360 iPatch shelf in an existing iPatch System, the iPatch Rack and Panel

Managers must be running firmware version 8.1 or later and the imVision®Controller must be running firmware

version 10.1 or later. The System Manager firmware, used to manage the system, must be version 7.1 or later.

We recommend that you upgrade the System Manager software to version 7.1 or a later version before you

install the shelf.

Ordering information is listed below:

Material ID

Part No.

Description

760169144

360G2-iP-1U-32-MPO-DP-SD

360G2 iPatch 1U 32-MPO distribution panel, sliding shelf

760169185

360G2-iP-2U-64-MPO-DP-SD

360G2 iPatch 2U 64-MPO distribution panel, sliding shelf

1U MPO Distribution Panel 2U MPO Distribution Panel

SYSTIMAX 360™iPatch®G2 MPO Fiber Sliding Shelves

This product is covered by one or more of the following U.S. patents or their foreign equivalents:

5,923,807, 6,245,998. The iPatch System is covered by U.S. patents 6,285,293, 6,522,737 and 8,344,900

860538982

Instruction Sheet

www.commscope.com

Page 2 of 9

How to Contact Us

To find out more about CommScope® products, visit us on the web at http://www.commscope.com/

For technical assistance:

-Within the United States, contact your local account representative or technical support at

1-800-344-0223. Outside the United States, contact your local account representative or

PartnerPRO™Network Partner.

-Within the United States, report any missing/damaged parts or any other issues to CommScope

Customer Claims at 1-866-539-2795 or email to claims@commscope.com. Outside the United

States, contact your local account representative or PartnerPRO Network Partner.

Tools Required

Flat-blade screwdriver

Phillips-head screwdriver

Specifications

Fiber Optic Interface

Industry-standard MPO

Compatible Fiber Size

Multimode with 50 µm core diameter, such as LazrSPEED®

Singlemode with 8.3 µm core diameter, such as TeraSPEED®

Environmental Data

Temperature Range: -40º F to 158º F (-40º C to 70º C) (storage)

23º F to 122º F (-5º C to 50º C) (operational)

Humidity: 95% noncondensing

Parts List

Verify parts against the parts list below:

Quantity

Description

Shelf assembly (sliding) with panel bus jumper

Trough assembly (includes door assembly)

Polycarbonate top cover

12-24 x 1/2 inch screws for mounting the shelf in a 19-inch (483mm) or 23-inch (584mm) rack

Liquid tight cable fittings (cable glands)

Corrugated tubing

Plastic cable tie retainers

Cable ties

Flat retainer clips

Shelf installation instruction sheet

Fiber cleaning instruction sheet

www.commscope.com

860538982

Instruction Sheet

Page 3 of 9

Separately Orderable Components

Material ID

Part No.

Description

760039883

600-23BRKT

Mounting bracket accessory kit for 23-inch (584mm) frame

Important: Limits for iPatch shelf and panel connections:

iPatch MPO fiber shelves are limited to a maximum number of rack units (RUs) and will not support a fully

populated rack or cabinet. iPatch MPO fiber shelves support 26 rows per rack/cabinet, such as configured

for (26) 1U shelves, (13) 2U shelves, (10) 2U UHD shelves, (6) 4U shelves, (5) 4U UHD shelves, or any

combination thereof.

iPatch MPO fiber shelves are limited to a maximum number of five (5) panels per panel bus male

connector.

Start a new panel bus chain with every sixth panel in the rack system.

Important Safety Cautions

To reduce the risk of fire, electric shock, and injury to persons, read, understand, and adhere to the following

instructions as well as any warnings marked on the product.

Remote risk of electric shock. Never install the product in wet locations or during lightning storms. Never

touch uninsulated communication wires or terminals.

Disconnected optical components may emit invisible optical radiation that can damage your eyes. Never

look directly into an optical component that may have a laser coupled to it. Serious and permanent retinal

damage is possible. If accidental exposure to laser radiation is suspected, consult a physician for an eye

examination.

Wear safety glasses to install the shelf. Although standard safety glasses provide no protection from

potential optical radiation, they offer protection from accidental airborne hardware and cleaning solvents.

Precautions

iPatch high density fiber modules require virtually no maintenance to maintain their performance. They

contain no user-serviceable components, and any damage to the anti-tamper label or removal of top cover

or front adapter mounting panel will void the warranty.

Fiber optic trunk cable and jumper performance is sensitive to bending, pulling, and crushing. Minimum

bend radius must be maintained during installation per the manufacturer’s specification. Appropriate pulling

socks must be used during installation, and pulling forces shall not exceed manufacturer’s

recommendations. MPO terminated trunk cables may use ribbonized fiber optic cable, which has a

preferential bend axis. Use caution to avoid kinking trunk cables.

All wiring that connects to this equipment must meet applicable local and national building codes and

network wiring standards for communication cable.

Care should be taken not to compromise the stability of the rack by installation of this equipment.

iPatch fiber shelves are for use in restricted access areas only.

SYSTIMAX 360 iPatch shelves use infrared sensing technology and should be installed where they are not

exposed to direct sunlight or other infrared sources.

iPatch high density fiber MPO adapters are equipped with protective dust caps installed in the front of all

adapters.

Prior to installation, clean the trunk cable and jumper connectors per the manufacturer’s recommendations.

860538982

Instruction Sheet

www.commscope.com

Page 4 of 9

Step 1 –Route Panel Bus Jumper

1. If it has not already been removed, slide the cover off the shelf.

2. Remove tape securing panel bus jumper to cable support.

3. Route the panel bus jumper with protective corrugated tubing around the end of the sliding rail to the outside

of the rail.

4. Snap the corrugated tubing protecting panel bus jumper into the cable retainer clip on the outside of rail as

shown.

5. Position the corrugated tubing so that about 3.5 inches (89mm) of tubing extends past the end of cable

retainer clip.

6. Position the exposed ribbon cable of the panel bus jumper in the flat retainer clips on the outside of the

sliding rail as shown above.

10-pin panel

bus jumper

connector

Panel

jumper

bus

Protective

corrugated tubing Flat retainer clips

3.5”

(89mm)

.....

www.commscope.com

860538982

Instruction Sheet

Page 5 of 9

Step 2 –Install Shelf and Connect Panel Bus Jumper

1. Mount the shelf in the rack using the four mounting screws provided.

For a 19-inch (483mm) rack, mount shelf to rack using the pre-installed mounting brackets and four

12-24 x 1/2-inch screws provided.

For a 23-inch (584mm) rack, use the 600-23BRKT accessory kit (ordered separately) and install one

conversion bracket on each side of shelf using four 10-32 x 3/8-inch screws included in the kit. Mount

shelf to rack using four 12-24 x 1/2-inch screws provided.

For an ETSI rack, use the 600-23BRKT accessory kit (ordered separately) and install one conversion

bracket on one side of the shelf using two of the four 10-32 x 3/8-inch screws included in the kit. Mount

shelf to rack using four M6 x 12 screws (not provided). The shelf will not be centered in the rack.

2. Connect the keyed female 10-pin connector on the panel bus jumper into the nearest cable bus port on

panel bus as shown.

3. Install spare port built into jumper cordage into panel bus frame by turning it at an angle, inserting into

frame, and turning it back perpendicular to frame.

860538982

Instruction Sheet

www.commscope.com

Page 6 of 9

Step 3 –Install Trough

For Unpopulated and Modular Shelves

1. Position trough on shelf so that indentions behind captive screws rest on the standoffs.

2. Using a Phillips head screwdriver, tighten the captive screw on each end of trough to secure it to shelf.

Note: If installing the trough on a sliding shelf, pull the shelf out enough to support the faceplate from behind

before tightening the captive screws.

www.commscope.com

860538982

Instruction Sheet

Page 7 of 9

Step 4 –Route Trunk Cable(s)

1. Pull shelf out to fully extended position.

2. Pull the trunk cable(s) to the rack and determine the best way to route the cable to the shelf (from above or

below).

3. The trunk cables and sub-units may enter shelf from right or left side of rear apron. Carefully loop cable to

rear of shelf on either side and continue to feed cable over top of rear apron. Loosely secure cable to rear of

shelf using a cable tie or hook-and-loop strap.

4. Temporarily store slack sub-units in shelf.

5. Remove plug from appropriate size opening in shelf to accommodate cable gland on fiber cable. Select an

opening on rear apron that will be most advantageous for cable entry.

6. Loosen locknut on cable gland. The locknut does not have to be removed to install the cable gland.

860538982

Instruction Sheet

www.commscope.com

Page 8 of 9

7. Feed sub-units through opening in shelf and temporarily coil sub-units loosely inside shelf.

8. Rotate locknut as required to allow it to pass through the opening and enter shelf.

Note: It may be necessary to temporarily remove a plug from an adjacent opening to provide sufficient

clearance for locknut to be inserted through opening.

9. Insert threaded body of cable gland into opening and tighten locknut onto threaded section to secure trunk

cable to shelf.

10. Using one of the methods described below, route and secure the trunk cable from the cable gland back to

the rack.

Method A

1. Working back from where the fiber cable enters shelf (at a cable gland), carefully loop cable over rear fiber

management bar and then to outside of shelf slide on opposite side of panel from cable entry point as

shown. Maintain cable in as small of a radius as possible while not exceeding minimum bend radius for

cable. Secure fiber cable to shelf slide in at least two places using cable ties or hook-and-loop straps

threaded through slots and punches provided in rails. Do not secure cables to fiber management bar.

2. From shelf slide, route cable to equipment rack and loosely secure cable to rack upright approximately

3 inches (76mm) above or below shelf, using a cable tie or hook-and-loop strap.

Note: Do not exceed minimum bend radius for fiber cable.

3. Verify that shelf retracts and extends fully before proceeding.

4. The ribbon cable of the panel bus jumper may slide in the corrugated tubing.

Method B

Note: This method reduces the slack loop length at rear of shelf but it requires an open space of at least 1U

above the shelf to work.

1. Working back from where the fiber cable enters shelf (at a cable gland), carefully loop cable over rear fiber

management bar and then across shelf slide on opposite side of chassis from cable entry point as shown.

Maintain cable in as small of a radius as possible while not exceeding the minimum bend radius for the

cable. Do not secure cables to fiber management bar or drawer slide.

2. Route cable to equipment rack and loosely secure cable to rack upright approximately 3 inches (76mm)

above or below shelf, using a cable tie or hook-and-loop strap.

3. Verify that shelf retracts and extends fully before proceeding.

4. The ribbon cable of the panel bus jumper may slide in the corrugated tubing.

Step 5 –Connect Cables to MPO Adapters

1. Remove protective dust covers from MPO connectors on the cable.

2. Prior to installation, clean all MPO connections per the manufacturer’s recommendations.

3. Grasp connector by its boot, near the base of connector. Insert MPO connector into coupler until it clicks into

place.

Note: The MPO connection is keyed. The polarized tab on the connector fits into the opening on a coupler

on adapters.

4. Insert each of the trunk cable’s MPO connectors into MPO couplers on adapters.

5. Route sub-units so that slack length is contained and so as to avoid tight bends as the connectors are

terminated into the adapter panels.

Note: To unplug an MPO connector, grasp the ribbed sleeve section and pull connector out of coupler.

Do not pull on the boot to unplug an MPO connector.

www.commscope.com

860538982

Instruction Sheet

Page 9 of 9

Step 6 –Install Cover and Door

Install top cover and trough door (both provided) to shield shelf from foreign particles. The cover, which is made

of clear, flame-retardant plastic, slides on and off shelf. The door for the patch cord trough is hinged and has

touch-latches for closing and opening.

1. Slide cover through flanges on shelf until cover reaches the back wall of shelf.

2. Remove door from protective wrapping.

3. Orient door at an angle from trough and position hinge pins on door into hinge sockets on trough.

4. Using one hand to support bottom of trough on one end, push down on inside of door over hinge pins with

other hand to seat pins into hinge sockets.

5. Repeat on other end to secure door to trough.

6. Pivot door into the vertical position until strikes engage latches and door snaps into the closed position with

an audible click.

7. Door may be reopened by pulling on both upper corners of door (opposite strikes) until the latches release

(verified by an audible click).

Note: Trough door may be removed when opened to a 45° position, by holding one of the side hinge

brackets and pulling upward until hinge pins release from socket. Lift door to release from hinge socket on

other side bracket.

8. Fully retract the shelf in the rack.

Step 7 –Trough Removal (If Required)

1. Using a Phillips head screwdriver, loosen the two captive screws located on the inside of the fiber

management rings on each end of the trough, then pull the trough off.

Note: Captive screws will not disengage from trough.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CommScope Netzwerk-Hardware Handbücher

CommScope

CommScope NOVUX DSC 650 Bedienungsanleitung

CommScope

CommScope LSX Bedienungsanleitung

CommScope

CommScope Mini-OTE 300 Bedienungsanleitung

CommScope

CommScope SD-4U-SPLICE PANEL Bedienungsanleitung

CommScope

CommScope NOVUX SEC 100 Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope ION-M23 SDARS Bedienungsanleitung

CommScope

CommScope NG4access ODF Platform Value-Added Module Bedienungsanleitung

CommScope

CommScope SYSTIMAX AirSPEED AP542 Bedienungsanleitung

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope Uniprise Solutions HFTP-HD6B-1U-24 Bedienungsanleitung

CommScope

CommScope CPPR-QF-F-1U-E Bedienungsanleitung

CommScope

CommScope SYSTIMAX EHD Bedienungsanleitung

CommScope

CommScope SCIL-B Bedienungsanleitung

CommScope

CommScope AMP NETCONNECT MRJ21 Bedienungsanleitung

CommScope

CommScope ION-M17EHP/19P Bedienungsanleitung

CommScope

CommScope EHD Bedienungsanleitung

CommScope

CommScope WCS-2 Bedienungsanleitung

CommScope

CommScope UNJ10G Bedienungsanleitung

CommScope

CommScope ION-M7P Bedienungsanleitung

CommScope

CommScope OneCell RP5000 Series Leitfaden

CommScope

CommScope RUCKUS SmartZone 300 Bedienungsanleitung

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Bedienungsanleitung

CommScope

CommScope Constellation CPT-PP-48C Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung