CommScope ION-U EU H 23/23 Bedienungsanleitung

ION®-U

EU H 23/23

Extension Unit

User's Manual

M0200ABA

Page 2 M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-

DISCLAIMER:

This document has been developed by CommScope, and is intended for the use of its

customers and customer support personnel. The information in this document is subject to

change without notice. While every effort has been made to eliminate errors, CommScope

disclaims liability for any difficulties arising from the interpretation of the information

contained herein. The information contained herein does not claim to cover all details or

variations in equipment, nor to provide for every possible incident to be met in connection

with installation, operation, or maintenance. This document describes the performance of the

product under the defined operational conditions and does not cover the performance under

adverse or disturbed conditions. Should further information be desired, or should particular

problems arise which are not covered sufficiently for the purchaser’s purposes, contact

CommScope.

CommScope reserves the right to change all hardware and software characteristics without

notice.

This document is protected by copyright. No part of this document may be reproduced,

stored in a retrieval system, or transmitted, in any form or by any means, electronic,

mechanical photocopying, recording, or otherwise without the prior written permission of

CommScope.

TRADEMARKS

All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of

CommScope. Names of products mentioned herein are used for identification purposes only

and may be trademarks and / or registered trademarks of their respective companies.

Andrew Wireless Systems GmbH, 22-April-2015

Table of Contents

M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-U Page 3

TABLE OF CONTENTS

1. GENERAL 6

1.1. USED ABBREVIATIONS 6

1.2. HEALTH AND SAFETY 7

1.3. PROPERTY DAMAGE WARNINGS 7

1.4. COMPLIANCE 8

1.5. ABOUT COMMSCOPE 11

1.6. INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT 12

2. INTRODUCTION 14

2.1. PURPOSE 14

2.2. ION-U HIGH POWER REMOTE AND EXTENSION UNITS 14

3. FUNCTIONAL DESCRIPTION 15

4. COMMISSIONING 16

4.1. GENERAL 16

4.2. HIGH POWER EU MECHANICAL INSTALLATION 16

4.2.1. Health and Safety for mechanical installation 16

4.2.2. Property Damage Warnings for mechanical installation 16

4.2.3. Mounting distance between RU and EU 18

4.2.4. Wall mounting procedure 19

4.2.5. Pole mounting procedure with screw bands 20

4.2.6. Pole mounting procedure with brackets 21

4.3. ELECTRICAL INSTALLATION 23

4.3.1. Health and Safety for electrical installation 23

4.3.2. Property Damage Warnings for electrical installation 23

4.3.3. Connections 25

4.3.4. Grounding (Earthing) 28

4.3.5. Connection of the antenna cables 28

4.3.5.1. Cleaning procedure for RF cable connectors 30

4.3.5.2. Antenna cable connector assembly 33

4.3.6. Mains power connection 34

4.3.6.1. Mains power connection AC 34

4.3.6.2. Mains power connection DC 36

4.3.7. Extension Unit port connections 38

4.3.8. Coupling Probe 39

4.4. COMMISSIONING FLOW-CHART 40

Table of Contents

Page 4 M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-U

5. ALARMS 42

5.1. BITE AND ALARMS 42

5.2. TROUBLESHOOTING 42

5.3. STATUS LED ALARMS 42

6. MAINTENANCE 43

6.1. GENERAL 43

6.2. REPLACING THE FAN UNIT 44

6.3. CLEANING THE HEAT SINK 45

7. APPENDIX 46

7.1. ILLUSTRATIONS 46

7.2. SPECIFICATIONS 47

7.3. SPARE PARTS 47

8. INDEX 48

Figures and Tables

M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-U Page 5

FIGURES AND TABLES

figure 3-1 ION-U high power EU system overview ................................................... 15

figure 4-1 Maximum distance between RU to EU or EU to EU................................. 18

figure 4-2 Wall mounting - pitches............................................................................ 19

figure 4-3 Pole mounting - pitches............................................................................ 20

figure 4-4 Pole mounting - screw bands................................................................... 20

figure 4-5 Pole mounting - fasten EU........................................................................ 20

figure 4-6 Pole mounting – max. diameter................................................................ 21

figure 4-7 Pole mounting – with brackets.................................................................. 21

figure 4-8 Pole mounting - pitches............................................................................ 22

figure 4-9 Pole mounting - brackets.......................................................................... 22

figure 4-10 Pole mounting - fasten EU...................................................................... 22

figure 4-11 ION-U EU H 23/23 AC version connector flange.................................... 25

figure 4-12 ION-U EU H 23/23 DC version connector flange.................................... 27

figure 4-13 Grounding bolts...................................................................................... 28

figure 4-14 Grounding bolt, schematic view.............................................................. 28

figure 4-15 Mains power connector .......................................................................... 35

figure 4-16 Mains power cable - AC ......................................................................... 35

figure 4-17 EU (Extension Unit) connector............................................................... 38

figure 4-18 EU connector and cable bridge.............................................................. 38

figure 4-19 Mounting the EU cable bridge................................................................ 39

figure 7-1 ION-U EU H 23/23 required space........................................................... 46

table 4-1 Specified torques....................................................................................... 17

table 4-2 ION-U EU H 23/23 connector flange.......................................................... 26

table 4-3 AC power cable pinning............................................................................. 35

table 4-4 EU connector pinning ................................................................................ 38

1. General

Page 6 M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-U

1. General

1.1.Used Abbreviations

AC/DC Alternating current / Direct

Current

AIMOS Andrew Integrated

Management and Operating

System

ALC Automatic Level Control

BITE Built-In Test Equipment

BTS Base Transceiver Station

CDMA Code Division Multiple Access

CE "Conformité Européenne"

("European Conformity")

CFR Code of Federal Regulations

CPD Channel Power Detection

DL Downlink

DoC Declaration of Conformity

EP Extension Port

ESD Electrostatic Discharge

EU Extension Unit

GSM Global System for Mobile

Communication

GND Ground (Earth)

GUI Graphical User Interface

ICP3 Intercept Point 3rd order

ID No Identification Number

ION Intelligent Optical Network

LED Light Emitting Diode

LMT Local Maintenance Terminal

LTE Long Term Evolution

MIMO Multiple Input Multiple Output

MS Mobile Station

MU Main Unit

NF Noise Figure

OMC Operations and Maintenance Center

OTRx Optical Transceiver = SRMU

(Subrack Master Unit)

PIM Passive Intermodulation

Pin Input power

Pout Output power

PSU Power Supply Unit

Rev Revision

RF Radio Frequency

RU Remote Unit

RX Receiver

SISO Single Input Single Output

SNMP Simple Network Management

Protocol

TX Transmitter

UL Uplink

UMTS Universal Mobile

Telecommunication System

UPS Uninterruptible Power Supply

VSWR Voltage Standing Wave Ratio

WCDMA Wideband Code Division

Multiple Access

WDM Wavelength Division Multiplex

XML Extensible Markup Language

1. General

M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-U Page 7

1.2.Health and Safety

1. Danger: Electrical hazard. Danger of death or fatal injury from electrical

current. Obey all general and regional installation and safety regulations

relating to work on high voltage installations, as well as regulations

covering correct use of tools and personal protective equipment.

2. Caution: High frequency radiation in operation. Risk of health hazards associated

with radiation from the unit’s inner conductor of the antenna port(s). Disconnect

mains before connecting or replacing antenna cables.

3. Caution: High frequency radiation in operation. Risk of health hazards associated

with radiation from the antenna(s) connected to the unit. Implement prevention

measures to avoid the possibility of close proximity to the antenna(s) while in

operation.

1.3.Property Damage Warnings

1. Attention: Due to power dissipation, the Extension Unit may reach a very high

temperature. Do not operate this equipment on or close to flammable materials.

Use caution when servicing the unit.

2. Notice: Although the Extension Unit is internally protected against overvoltage, it

is strongly recommended to ground (earth) the antenna cables close to the

repeater’s antenna connectors for protection against atmospheric discharge.

3. Notice: ESD precautions must be observed. Before commencing maintenance

work, use the available grounding (earthing) system to connect ESD protection

measures.

4. Notice:Only suitably qualified personnel are allowed to work on this unit and only

after becoming familiar with all safety notices, installation, operation and

maintenance procedures contained in this manual.

5. Notice: Keep operating instructions within easy reach and make them available

to all users.

6. Attention:Only authorized and trained personnel are allowed to open the unit

and get access to the inside.

7. Notice: Read and obey all the warning labels attached to the unit. Make sure that

all warning labels are kept in a legible condition. Replace any missing or

damaged labels.

1. General

Page 8 M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-U

8. Notice: Only license holders for the respective frequency range are allowed to

operate this unit.

9. Notice: Make sure the repeater settings are correct for the intended use (refer to

the manufacturer product information) and regulatory requirements are met. Do

not carry out any modifications or fit any spare parts, which are not sold or

recommended by the manufacturer.

1.4.Compliance

1. Notice:For installations which have to comply with European EN50385 exposure

compliance requirements, the following Power Density limits/guidelines (mW/cm²)

according to ICNIRP are valid:

o0.2 for frequencies from 10 MHz to 400 MHz

oF (MHz) / 2000 for frequencies from 400 MHz to 2 GHz

o1 for frequencies from 2 GHz to 300 GHz

2. Notice: For installations, which have to comply with FCC RF exposure

requirements, the antenna selection and installation must be completed in a way

to ensure compliance with those FCC requirements. Depending on the RF

frequency, rated output power, antenna gain, and the loss between the repeater

and antenna, the minimum distance D to be maintained between the antenna

location and human beings is calculated according to this formula:

]/[

][

cmmW

D∗∗

where

•P (mW) is the radiated power at the antenna, i.e. the max. rated repeater

output power in addition to the antenna gain minus the loss between the

repeater and the antenna.

•PD (mW/cm²) is the allowed Power Density limit acc. to 47 CFR 1.1310 (B)

for general population / uncontrolled exposures which is

oF (MHz) / 1500 for frequencies from 300MHz to 1500MHz

o1 for frequencies from 1500MHz to 100,000MHz

RF exposure compliance may need to be addressed at the time of licensing, as

required by the responsible FCC Bureau(s), including antenna co-location

requirements of 1.1307(b)(3).

3. Notice: Installation of this equipment is in full responsibility of the installer, who

has also the responsibility, that cables and couplers are calculated into the

maximum gain of the antennas, so that this value, which is filed in the FCC Grant

and can be requested from the FCC data base, is not exceeded. The industrial

boosters are shipped only as a naked booster without any installation devices or

antennas as it needs for professional installation.

1. General

M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-U Page 9

4. Notice: For installations which have to comply with FCC/Industry Canada

requirements:

English:

This device complies with FCC Part 15 and Industry Canada license exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

This device complies with Health Canada’s Safety Code. The installer of this device

should ensure that RF radiation is not emitted in excess of the Health Canada’s

requirement. Information can be obtained at http:

//www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

French:

Cet appareil est conforme à FCC Partie15 d’Industrie Canada RSS standard exempts de

licence (s). Son utilisation est soumise à Les deux conditions suivantes: (1) cet appareil

ne peut pas provoquer d’interférences et (2) cet appareil doit accepter Toute

interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement

du dispositif.

Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme

d’installation de cet appareil doit s’assurer que les rayonnements RF n’est pas émis au-

delà de I’exigence de Santé Canada. Les informations peuvent être obtenues:

http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-fra.php

Les changements ou modifications non expressément approuvés par la partie

responsable de la conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet

équipement.

5. Notice: Corresponding local particularities and regulations must be observed. For

national deviations, please refer to the respective documents included in the

manual CD that is delivered with the unit.

6. Notice:The unit complies with Overvoltage Category II. It also complies with the

surge requirement according to EN 61000-4-5 (fine protection); however,

installation of an additional medium (via local supply connection) and/or coarse

protection (external surge protection) is recommended depending on the

individual application in order to avoid damage caused by overcurrent.

For Canada and US, components used to reduce the Overvoltage Category shall

comply with the requirements of IEC 61643-series. As an alternative,

components used to reduce the Overvoltage Category may comply with

ANSI/IEEE C62.11, CSA Certification Notice No. 516, CSA C22.2 No. 1, or UL

1449. Suitability of the component for the application shall be determined for the

intended installation.

1. General

Page 10 M0200ABA_ION-U_EU_H_23_23 User’s Manual for ION®-U

7. Note: For a Class A digital device or peripheral:

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

8. Note: This unit complies with European standard EN60950.

Equipment Symbols Used / Compliance

Please observe the meanings of the following symbols used in our equipment and

the compliance warnings:

Symbol

Compliance

Meaning / Warning

--- FCC

For industrial (Part 20) signal booster:

WARNING: This is NOT a CONSUMER device. It is

designed for installation by FCC LICENSEES and

QUALIFIED INSTALLERS. You MUST have an FCC

LICENSE or express consent of an FCC Licensee to

operate this device. Unauthorized use may result in

significant forfeiture penalties, including penalties in

excess of $100,000 for each continuing violation.

Alert sign to R&TTE

To be sold exclusively to mobile operators or

authorized installers –no harmonized frequency

bands, operation requires license. Intended use: EU

and EFTA countries

Indicates conformity with the R&TTE directive

1999/5/EC certified by the notified body no. 0700.

Note: The Manufacturer's rated output power of this equipment is for single carrier

operation. For situations when multiple carrier signals are present, the rating would

have to be reduced by 3.5 dB, especially where the output signal is reradiated and

can cause interference to adjacent band users. This power reduction is to be by

means of input power or gain reduction and not by an attenuator at the output of the

device.

Inhaltsverzeichnis

Andere CommScope Netzwerk-Hardware Handbücher

CommScope

CommScope CPPR-QF-F-1U-E Bedienungsanleitung

CommScope

CommScope SYSTIMAX 100BASE-T Bedienungsanleitung

CommScope

CommScope SCIL-B Bedienungsanleitung

CommScope

CommScope NG4access ODF Platform Value-Added Module Bedienungsanleitung

CommScope

CommScope Constellation CPT-PP-48C Bedienungsanleitung

CommScope

CommScope ONECELL RP5200 Handbuch

CommScope

CommScope SYSTIMAX 360 iPatch G2 MPO Bedienungsanleitung

CommScope

CommScope RUCKUS SmartZone 300 Bedienungsanleitung

CommScope

CommScope NETCONNECT 1479542-1 Bedienungsanleitung

CommScope

CommScope NOVUX DSC 650 Bedienungsanleitung

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Bedienungsanleitung

CommScope

CommScope FOSC-OC-6 Bedienungsanleitung

CommScope

CommScope WCS-2 Bedienungsanleitung

CommScope

CommScope ST-BSP60 Bedienungsanleitung

CommScope

CommScope RUCKUS SmartZone 100 Bedienungsanleitung

CommScope

CommScope SYSTIMAX EHD Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope TC-96370-IP Bedienungsanleitung

CommScope

CommScope ION-M23 SDARS Bedienungsanleitung

CommScope

CommScope LSX Bedienungsanleitung

CommScope

CommScope ION-U EU H 7P/80-85P/17P/19P Bedienungsanleitung

CommScope

CommScope FPX Series Bedienungsanleitung

CommScope

CommScope OneCell RP5000 Series Leitfaden

CommScope

CommScope FDC-W8-FAT Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung