Comnet CNFE4+1SMSM2 Bedienungsanleitung

INS_CNFE4+1SMS(M,S)2_REVA 07/08/11 PAGE 1

INSTALLATION AND OPERATION MANUAL

CNFE4+1SMS(M,S)2

FOUR PORT 10/100T(X) + ONE PORT 100FX

ETHERNET SELF-MANAGED SWITCH

The ComNet™CNFE4+1SMS(M,S)2 is a five-port self-managed Ethernet switch with

uplink management functionality. It provides four ports operating at 10/100Mbps

and is designed to combine Ethernet data from the four electrical ports into a single

optical port and forward that data to the next network device, using two-fiber ST or

SC optical connectors. There is no programming required to use this switch. The

ComNet CNFE4+1SMS comes pre-programmed, preventing network video flooding

with DIP switch selection of the fiber port as uplink or as an unmanaged switch It is

“Plug-and-Play” easy to use.

LED indicators confirm the operating status of this device. See Figure 4 on Page 3

for an explanation of the indicators.

The ComNet CNFE4+1SMS may be either wall mounted, rack mounted (“ComFit”

packaging) or DIN-rail mounted with the use of the ComNet DINBKT1 adapter. See

Figure A on Page 4 for mounting instructions.

See Figures 1 – 5 for complete installation details.

INS_CNFE4+1SMS(M,S)2_REVA 07/08/11 PAGE 2

Tech SupporT: 1.888.678.9427

INSTALLATION AND OPERATION MANUAL CNFE4+1SMS(MS)2

OPTICAL

FIBER

RJ-45

BLACK

BLACK WITH WHITE STRIPE

Power Supply:

Surface Mount: 9–24VDC@1A

Rack Mount: From Rack

NOTE: Remove Electrical

Connector for Rack

Mount Units

FIGURE 2 – CNFE4+1SMS

FIGURE 1 – CNFE4+1SMS

REAR PANELFRONT PANEL

FIGURE 3 – UPLINK SWITCH SETTINGS

EFFECT UPLINK

Uplink Enabled ON

Uplink Disabled OFF

INS_CNFE4+1SMS(M,S)2_REVA 07/08/11 PAGE 3

Tech SupporT: 1.888.678.9427

INSTALLATION AND OPERATION MANUAL CNFE4+1SMS(MS)2

EFFECT UPLINK

Uplink Enabled ON

Uplink Disabled OFF

FIGURE 4 – LED INDICATORS

LINK (P5) LINK (P1 – P4) PWR

SOLID Link Up Link Up Power Applied

BLINKING Data Activity Data Activity –

OFF No Data Link No Data Link Power Not Applied

FIGURE 5 – APPLICATION DIAGRAM WITH MULTICAST TRAFFIC

IGMP Enabled on CNGE2FE24MODMS, Uplink enabled on the units

Camera

Connections

on Ports 2 – 4

Camera

Connections

on Ports 1 – 3

Camera

Connections

on Ports 1 – 4

CNGE2FE24MODMS

CNFE4SMS CNFE4+1SMS

CNFE5SMS

Copper

Fiber Optic

LEGEND

INS_CNFE4+1SMS(M,S)2_REVA 07/08/11 PAGE 4

3 CORPORATE DRIVE | DANBURY, CT 06810 | USA

T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET

8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE

T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET

MECHANICAL INSTALLATION INSTRUCTIONS

INSTALLATION CONSIDERATIONS

This switch is supplied as a Standalone/Rack module. Units should be

installed in dry locations protected from extremes of temperature and

humidity.

C1-US, C1-EU, C1-AU OR C1-CH CARD CAGE RACKS

CAUTION: Although the units are hot-swappable and may be installed

without turning power off to the rack, ComNet recommends that the

power supply be turned off and that the rack power supply is disconnected

from any power source. Note: Remove electrical connector before

installing in card cage rack.

1. Make sure that the card is oriented right side up, and slide it into the

card guides in the rack until the edge connector at the back of the card

seats in the corresponding slot in the rack’s connector panel. Seating

may require thumb pressure on the top and bottom of the card’s front

panel.

CAUTION: Take care not to press on any of the LEDs.

2. Tighten the two thumb screws on the card until the front panel of the

card is seated against the front of the rack.

WARNING: Unit is to be used with a Listed Class 2 or LPS power supply.

IMPORTANT SAFEGUARDS:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment may

be greater than room ambient. Therefore, consideration should be given to

installing the equipment in an environment compatible with the maximum

ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such

that the amount of air flow required for safe operation of the equipment is not

compromised.

FIGURE A

Dimensions are for a standard ComNet™one slot module

.156 [3.96 mm]

.313 [7.95 mm]

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Comnet Netzwerk-Router Handbücher

Comnet

Comnet CNGE3FE7MS4 Bedienungsanleitung

Comnet

Comnet RLXE4GE24MODMS Bedienungsanleitung

Comnet

Comnet CWFE8MS/DIN Bedienungsanleitung

Comnet

Comnet reliance RL1000GW Bedienungsanleitung

Comnet

Comnet NW7/M Bedienungsanleitung

Comnet

Comnet CNGE24FX12TX12MSPOE Bedienungsanleitung

Comnet

Comnet CNGE8US Series Bedienungsanleitung

Comnet

Comnet RLXE4GE24MODMS Bedienungsanleitung

Comnet

Comnet CNGE2FE8MSPOE Bedienungsanleitung

Comnet

Comnet CNGE28FX4TX24MS2 Betriebsanleitung

Comnet

Comnet CNGE8FX4TX4MS Bedienungsanleitung

Comnet

Comnet CLFE4US1TPC Bedienungsanleitung

Comnet

Comnet CWGE2FE8MSPOE Bedienungsanleitung

Comnet

Comnet CWFE8TX8MS Bedienungsanleitung

Comnet

Comnet netwave NW3 Einrichtungshandbuch

Comnet

Comnet CNGE3FE8MS Bedienungsanleitung

Comnet

Comnet CNGE11FX3TX8MS Bedienungsanleitung

Comnet

Comnet CNGE3FE8MSPOE Bedienungsanleitung

Comnet

Comnet CWGE9MS Bedienungsanleitung

Comnet

Comnet CNGE5MS Bedienungsanleitung

Comnet

Comnet CNFE10MS Bedienungsanleitung

Comnet

Comnet CNGE24MS Bedienungsanleitung

Comnet

Comnet CWGE24MS2 Bedienungsanleitung

Comnet

Comnet CLFE4+1SMS[POE](C Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise