Comnet CNGE24MS Bedienungsanleitung

INSTALLATION AND OPERATION MANUAL

CNGE24MS

ENVIRONMENTALLY HARDENED MANAGED ETHERNET SWITCH

WITH (8) 100/1000BASE-FX & (16) GIGABIT COMBO PORTS

v1.4 February 25, 2013

The ComNet™CNGE24MS has eight 100/1000Base-FX SFP ports and sixteen Gigabit

combo ports that allow for TX or FX transmission. All SFP ports utilize ComNet Small

Form Factor (SFP) pluggable modules for the selection of fiber and connector type and

distance. The IEEE802.3-compliant unit offers multiple Ethernet redundancy protocols

(ComRing, C-Ring, and MSTP/RSTP/STP) which protect your applications from network

interruptions or temporary malfunctions by redirecting transmission within the

network. The switch provides advanced IP-based management that can limit the

maximum bandwidth for each connected IP device, allowing the user to adjust

usage. Application-based QoS can set a higher priority for data streaming. The Device-

Binding function can prevent unauthorized network access, increasing security. The

unit also provides advanced DOS/DDOS auto prevention. If IP flow becomes too large,

too quickly, the switch will lock the source IP address for a set period preventing

unauthorized access. The switch offers centralized and convenient management and

is also configurable by Web-based Telnet, and Console (CLI) configurations.

INS_CNGE24MS_REV–

02/18/13 PAGE 2

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

Contents

Regulatory Compliance Statement 3

Warranty 3

Disclaimer 3

Safety Indications 3

Overview 4

Introduction 4

Software Features 5

Hardware Features 6

Hardware Overview 7

Front Panel 7

Rear Panel 8

Rack mount kit assembly 9

Front Panel LEDs 10

Cables 11

Ethernet Cables 11

10/100/1000BASE-T(X) Pin Assignments 11

SFP 13

Console Cable 14

WEB Management 16

Configuration by Web Browser 16

About Web-based Management 16

Command Line Interface Management 92

About CLI Management 92

Technical Specifications 105

INS_CNGE24MS_REV–

02/18/13 PAGE 3

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

Regulatory Compliance Statement

Product(s) associated with this publication complies/comply with all applicable regulations. Please

refer to the Technical Specifications section for more details.

Warranty

ComNet warrants that all ComNet products are free from defects in material and workmanship

for a specified warranty period from the invoice date for the life of the installation. ComNet will

repair or replace products found by ComNet to be defective within this warranty period, with

shipment expenses apportioned by ComNet and the distributor. This warranty does not cover

product modifications or repairs done by persons other than ComNet-approved personnel, and

this warranty does not apply to ComNet products that are misused, abused, improperly installed,

or damaged by accidents.

Please refer to the Technical Specifications section for the actual warranty period(s) of the

product(s) associated with this publication.

Disclaimer

Information in this publication is intended to be accurate. ComNet shall not be responsible for its

use or infringements on third-parties as a result of its use. There may occasionally be unintentional

errors on this publication. ComNet reserves the right to revise the contents of this publication

without notice.

Safety Indications

»The equipment can only be accessed by trained ComNet service personnel.

»This equipment should be installed in secured location.

INS_CNGE24MS_REV–

02/18/13 PAGE 4

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

Overview

Introduction

The CNGE24MS series are managed redundant ring Ethernet switches with 16xGigabit combo

ports and 8x100/1000Base-X SFP ports. With complete support of Ethernet Redundancy protocol,

C-Ring (recovery time <20ms over 250 units of connection) and MSTP/RSTP/STP (IEEE IEEE

802.1s/w/D) can protect your mission-critical applications from network interruptions or temporary

malfunctions with its fast recovery technology. ComNet switches provide advanced and IP-based

bandwidth management that can limit the maximum bandwidth for each IP device. The user can

configure IP camera and NVR with more bandwidth and limit other device bandwidth. ComNet’s

switch series also support application-based QoS. Application-based QoS can set highest priority

for data stream according to TCP/UDP port number. And all functions of CNGE24MS can also be

managed centralized and convenient by e-Console, as well as the Web-based interface, Telnet

and console (CLI) configuration. Therefore, the switch is one of the most reliable choice for highly-

managed and Gigabit Fiber Ethernet applications.

INS_CNGE24MS_REV–

02/18/13 PAGE 5

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

Software Features

»Fastest Redundant Ethernet Ring (Recovery time <20ms over 250 units connection)

»Supports Ring Coupling, Dual Homing, and RSTP-over-Ring

»Supports SNMPv1/v2/v3 & RMON & Port base/IEEE 802.1Q VLAN Network Management

»Event notification by Email, SNMP trap and Relay Output

»Web-based, Telnet, and Console (CLI) configuration

»Enable/disable ports, MAC based port security

»Port-based network access control (IEEE 802.1x)

»VLAN (IEEE 802.1q) to segregate and secure network traffic

»RADIUS centralized password management

»SNMPv3 encrypted authentication and access security

»RSTP (IEEE 802.1w)

»Quality of Service (IEEE 802.1p) for real-time traffic

»VLAN (IEEE 802.1q) with support for double-tagging and GVRP

»IGMP Snooping for multicast filtering

»Port configuration, status, statistics, mirroring, and security

»Remote Monitoring (RMON)

INS_CNGE24MS_REV–

02/18/13 PAGE 6

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

Hardware Features

»3 ×Redundant power inputs

»Operating Temperature: -40 to 75°C

»Storage Temperature: -40 to 85°C

»Operating Humidity: 5% to 95%, non-condensing

»Casing: IP-30 Aluminum

»16 ×Combo ports with 10/100/1000Base-T(X) and 100/1000Base-X SFP

»8 ×100/1000Base-X SFP ports

»Console Port

»Dimensions (W ×D ×H): 431 ×342 ×44 mm

INS_CNGE24MS_REV–

02/18/13 PAGE 7

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

Hardware Overview

Front Panel

The following table describes the labels that are affixed to the CNGE24MS.

Port Description

SFP ports 16 ×100/1000BaseX on SFP port(combo) &

8 ×100/1000BaseX on SFP port

Giga Ethernet Port 16 ×10/100/1000Base-T (combo)

Console Use RS-232 with DB9 connecter to manage switch.

1 5 6 72 3

CNGE24MS Front Panel

1. Console port (DB9)

2. 10/100/1000Base-T(X) Ethernet port and 100/1000Base-X SFP (combo port)

3. 100/1000Base-X Fiber port on SFP

4. Reset button: Push the button 3 seconds for reset; 5 seconds for factory default.

5. LED for Ethernet ports 1000Mbps Link/Act status

6. LED for Ethernet ports 10/100Mbps Link/Act status

7. LED for SFP ports Link/Act status

8. Front Panel LED Status:

»LED for PW1: When the PWR1 links, the green LED will be light on.

»LED for PW2: When the PWR2 links, the green LED will be light on.

»LED for PW3: When the PWR3 links, the green LED will be light on.

INS_CNGE24MS_REV–

02/18/13 PAGE 8

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

»LED for STA: Green: Indicates that the system ready. The LED is blinking when the system is

upgrading firmware

»LED for PWR: This LED lights on when the power module is activated.

»LED for R.M. (Ring master): When the LED lights on, this switch is designated as the ring

master of the Ring topology.

»LED for Ring: When the LED light on, the C-Ring is activated.

»LED for DEF: System resets to default configuration.

»LED for Ping: System is processing “PING” request.

»LED for RUN: System is operating continuously.

»LED for RMT: System is accessed remotely.

»LED for Fault: Indicates unexpected event occurred.

Rear Panel

The rear panel of CNGE24MS is displayed as below:

1 2 3

CNGE24MS Rear Panel

1. Power Switch

2. Power input for AC 100V~240V / 50~60Hz.

3. Power input for DC 36~72V and fault relay output

INS_CNGE24MS_REV–

02/18/13 PAGE 9

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

Rack mount kit assembly

You can find the rack-mount kit and the screws in the packing box. Please assemble the rack-

mount kit on the switch with screws as shown below:

INS_CNGE24MS_REV–

02/18/13 PAGE 10

INSTALLATION AND OPERATION MANUAL CNGE24MS

Tech SupporT: 1.888.678.9427

Front Panel LEDs

LED indicators

LED Color Status Description

PW1 Green On PWR1 linked

PW2 Green On PWR2 linked

PW3 Green On PWR3 linked

STA Green On The power module is in PWR UP state

Blinking The system is upgrading firmware

DEF Green On System resets to default configuration

RUN Green Slowly blinking System is operating continuously

PWR Green On DC power module activated

Ping Green Blinking System is processing “PING” request

RMT Green Blinking System is accessed remotely

Ring Green On Ring enabled

Slowly blinking Ring has only One link (lacks one link to build the ring)

Fast blinking Ring working normally

R.M Green On The system is operating in C-Ring Master mode

Fault Amber On Unexpected event occurred.

10/100/1000Base-T(X) Gigabit Ethernet ports

LINK/

ACT

Green On Port speed 1000Mbps link up

Blinking Data Transmitted at 1000Mbps

Amber On Port speed 10/100Mbps link up

Blinking Data Transmitted at 10/100Mbps

SFP

LINK/

ACT

Green On Port link up

Blinking Data transmitted

Inhaltsverzeichnis

Andere Comnet Netzwerk-Router Handbücher

Comnet

Comnet CNGE3FE8MSPOE Bedienungsanleitung

Comnet

Comnet CNGE2FE24MS Bedienungsanleitung

Comnet

Comnet CNGE3FE8MS Bedienungsanleitung

Comnet

Comnet CWGE2FE24MODMS Bedienungsanleitung

Comnet

Comnet CWFE2COAX Betriebsanleitung

Comnet

Comnet CNGE8FX4TX4MS Bedienungsanleitung

Comnet

Comnet CNGE11FX3TX8MS Bedienungsanleitung

Comnet

Comnet CLFE4+1SMS[POE](C Bedienungsanleitung

Comnet

Comnet CNGE5MS Bedienungsanleitung

Comnet

Comnet CNGE2FE8MSPOE Bedienungsanleitung

Comnet

Comnet CWGE2FE8MSPOE Bedienungsanleitung

Comnet

Comnet CWFE8TX8MS Bedienungsanleitung

Comnet

Comnet CNFE10MS Bedienungsanleitung

Comnet

Comnet CWFE8MS/DIN Bedienungsanleitung

Comnet

Comnet RLXE4GE24MODMS Bedienungsanleitung

Comnet

Comnet NW7/M Bedienungsanleitung

Comnet

Comnet CNGE28FX4TX24MS2 Betriebsanleitung

Comnet

Comnet CLFE4US1TPC Bedienungsanleitung

Comnet

Comnet CWGE24MS2 Bedienungsanleitung

Comnet

Comnet CNGE20FX4TX16MS Betriebsanleitung

Comnet

Comnet CNGE24FX12TX12MSPOE Bedienungsanleitung

Comnet

Comnet reliance RL1000GW Bedienungsanleitung

Comnet

Comnet CNFE4+1SMSM2 Bedienungsanleitung

Comnet

Comnet CWGE9MS Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise