CoolGear CG-10U2AML Bedienungsanleitung
1
Thank you for purchasing this high-speed 10-port USB2.0 hub. It
provides an ideal solution to expand 10 USB2.0 ports from one
single USB2.0 host port. It provides a wide range self power
source (+5~24VDC from the 2-pin Terminal Blocks or DC Jack) to
supply enough power on USB2.0 buses.
Features:
✓Compliant with USB Specification 2.0
✓Metal Case, DIN Rail and wall mountable
✓Provides 10 Downstream USB2.0 Facing Ports
✓Supports USB Screw-Lock Mechanism for Both Type-B and
Type-A Cables
✓Supports 480Mbps (High speed), 12Mbps (Full-speed) and
1.5Mbps (Low-speed) Speed
✓Supports 15KV ESD Level 4 Protection for Each Port
✓Supports +5~24V DC Wide Range Input Power
✓Power Inputs: DC-Jack or Terminal Blocks
10-Port USB2.0 Metal Hub
with 15KV ESD Surge Protection and Rack/DIN-RAIL Mounting Kit
Installation Guide
1. Introduction
2. Connector Layout
Power LED
10 USB2.0 Downstream Port
Connectors
USB2.0 Upstream Port Connector
+5~24V DC Power Input DC
Jack and Terminal Blocks
10-Port Managed USB2.0 Metal Hub with 15KV ESD Surge Protection
2
⚫USB2.0 Upstream Port Connector: Type-B connector from
upstream USB2.0 port. It is connected from host or another
USB2.0 hub. Supports both normal and screw-lock type USB
cables.
⚫USB2.0 Downstream Port Connectors: There are 10 Type-A
connectors for USB2.0 or USB1.1 devices. They support both
normal and screw-lock type USB cables.
⚫Self Power Input Connectors: This 2-pin (one pin plus voltage
and the other pin is GND) terminal block connector and DC
Jack are used to connect external power to self-power the
hub, the voltage can be in the range from +5V to 24V DC.
WARNING!!
Please make sure the polarity of the input power should be
correctly matched with the terminal block pins to function
properly.
1. Use static electricity discharge precautions.
Remove possible static discharge potential from any objects
that the hub may come in contact with before installation.
This can be accomplished by touching a bare metal chassis
rail after you have turned off the power.
2. Apply DC power (range from +5V to 24V) to the 2-pin
Terminal Block Connector or DC Jack. The hub was
bus-powered by the upstream USB port, and was
self-powered by either of the 2 connectors to add power to
ensure enough power for the 10 downstream ports.
3. Connecting USB Host cable: The host cable is either a
standard A-to-B USB2.0 cable or a screw-lock type A-to-B
cable. Please connect the type-A end connector of the
3. Hardware Installation
+5~24V
GND
+
-
10-Port Managed USB2.0 Metal Hub with 15KV ESD Surge Protection
3
cable to your upstream USB port, then connect the type-B
end connector to this hub. Since the USB hub is
plug-and-play, you don’t have to turn off your host computer
when installing the hub.
Note: In some cases, you will see an error message said
the USB bus power over the current limit, please ignore this
message since the hub is hot plug and its power capacitor
will cause a very short period of current. It will NOT affect your
USB function.
4. Connect the USB devices to the downstream ports of this hub.
5. Mount your hub on the wall or DIN RAIL (with optional
mounting kit) if required.
DIN RAIL Mount (horizontal):
DIN RAIL Mount (vertical):
Wall
Mounting
Holes
DIN RAIL Clips
Mounted on the DIN RAIL vertically
Mounted on the DIN RAIL horizontally
DIN
RAIL
Clip
s
Wall
Mounting
Holes
10-Port Managed USB2.0 Metal Hub with 15KV ESD Surge Protection
4
To check the USB2.0 hub installation in Windows device
manager, please follow the following steps:
1. Click Start ➔Control Panel ➔System ➔Device Manager
button
2. Double click Universal Serial Bus Controller
3. Double click Generic USB Hub, the message will show that
this device is working properly.
Operating temp.: 0 to 60°C (32 to 140°F)
Operating humidity: 5 to 95% RH (non-condensing)
Dimensions (LxWxH): 7.78”(L)x2.18”(W)x1.22”(H)
(19.77x5.55x3.1cm)
5. Environmental Specifications
4. Checking the Hub Installation
Here is your USB2.0 Hub
Inhaltsverzeichnis
Andere CoolGear Schalten Handbücher
CoolGear
CoolGear USBG-10XU1 Bedienungsanleitung
CoolGear
CoolGear CG-10PU3MGD Bedienungsanleitung
CoolGear
CoolGear CG-4P31CHUB Bedienungsanleitung
CoolGear
CoolGear USBG-4U3MLR2 Bedienungsanleitung
CoolGear
CoolGear USBG-4U2ML Bedienungsanleitung
CoolGear
CoolGear USBG-7U2ML Bedienungsanleitung
CoolGear
CoolGear USBG-4SU2MLA Bedienungsanleitung
CoolGear
CoolGear USBG3-3X4M Bedienungsanleitung
CoolGear
CoolGear USBG-4U3ML Bedienungsanleitung
CoolGear
CoolGear USBG-4U2ML Bedienungsanleitung
CoolGear
CoolGear USBG-7DU2S Bedienungsanleitung
CoolGear
CoolGear CG-U31iS4PH Bedienungsanleitung
CoolGear
CoolGear USB3- 16U1 Bedienungsanleitung
CoolGear
CoolGear USBG-7U3ML Bedienungsanleitung
CoolGear
CoolGear USBG-3X4M Bedienungsanleitung
CoolGear
CoolGear USBG-7DU2i Bedienungsanleitung
CoolGear
CoolGear CG-UC31PD4H Bedienungsanleitung
CoolGear
CoolGear CG-7PU31HB Bedienungsanleitung
CoolGear
CoolGear CG-7PU313C Bedienungsanleitung
CoolGear
CoolGear USBNET-400i Bedienungsanleitung
