Cooper Lighting Combolight Trimmed V90229-1T Bedienungsanleitung

MOUNTING

CHANNEL

BUTTERFLY

MOUNTING

BRACKETS

HEX

SCREW

Figure 1

JBOX

JBOX COVER

SCREW

HOUSING

TRIM

TORSION

SPRING

CEILING

MATERIAL

HOUSING

TRIM

FIXTURE MOUNTING:

1. Fixture must be mounted using either BUTTERFLY MOUNTING

BRACKETS or HANGER BARS (Contact RSA Dealer for HANGER BARS).

INSTALLATION NOTE:

DO NOT install insulation within 3in of any part of the Luminaire.

Blinking light of this thermally protected Luminaire may indicate overheating.

BUTTERFLY MOUNTING:

2. Fixture comes equipped with universal BUTTERFLY MOUNTING

BRACKETS that can take common 1" or 1-1/2" black iron or galvanized

MOUNTING CHANNELS (supplied by others). See Fig 1.

3. Position fixture so the MOUNTING CHANNELS lie on top of the ceiling

runners.

4. Fasten MOUNTING CHANNELS securely to ceiling runners.

5. Secure MOUNTING CHANNELS to universal BUTTERFLY MOUNTING

BRACKETS with wire tie downs.

6. The BUTTERFLY MOUNTING BRACKETS are height-adjustable and

should be set so that the APERTURE COLLAR will be flush with the

finished ceiling plane.

Figure 3

ELECTRICAL:

7. Remove the JBOX COVER from the JBOX by removing the four SCREWS.

Connect supply lead wires to junction box lead wires in accordance with

your local electrical code(s) or N.E.C. Replace JBOX COVER onto JBOX,

securing with SCREWS. See Fig 2.

CEILING MATERIAL INSTALLATION:

8. Pull the TRIM away from the HOUSING. The TORSION SPRINGS will hold

the TRIM onto the HOUSING. Compress the TORSION SPRINGS on each

end of the TRIM, releasing the TRIM from the HOUSING. See Fig 3.

Figure 2

9. A clean, square hole in the CEILING MATERIAL must be cut. Install the

ceiling material below housing as seen in Fig 4.

10. Replace the TRIM into the HOUSING by connecting the TORSION

SPRINGS to the HOUSING. Push the TRIM into the HOUSING until flush

with the CEILING MATERIAL as seen in Fig 4.

Figure 4

INSTALLATION INSTRUCTIONS

V90229-1T

Avoid Fire or Electric Shock

COMBOLIGHT

TRIMMED

Page 1 of 3

THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

*Installation Instructions for qualified electricians only.

*Install per National Electrical Code and local regulations.

*Read Installation Instructions completely before installation.

*Failure to follow Installation Instructions may void warranties.









COVER

RING

BACK RING

COIL SPRING

LAMP

(MR16 shown, COIL

SPRING behind)

BACK RING

SOCKET ASSY

PIVOT JOINT

(FOR GIMBAL

TIGHTENING)

OPTICAL

ACCESSORY

RETAINER

RING

COVER

RING

SNOOT

Flush Position

Regressed Position

CEILING

LINE

11. Lamp installation:

To install LAMP, remove the COVER RING by pushing straight back on

the COVER RING and then turning it

counter-clockwise

to release.

See Fig. 5.

12. Once removed, insert the properly-specified LAMP into the

BACK RING, ensure that the LAMP is the correct LAMP for the SOCKET

or damage to the fixture or lamp may occur. The LAMP will seat into the

COIL SPRING when installed properly. While holding the LAMP in place,

grab the SOCKET ASSY and plug or screw the LAMP firmly into it.

See Fig. 6.

Figure 7

Figure 6

(Cover Ring Removed)

Figure 8

Figure 5

13. Optical Accessory: (skip to Step 21 if not using optical accessories)

To install OPTICAL ACCESSORY pieces, remove the ACCESSORY

RETAINER RING by unthreading until it is completely removed from the

COVER RING.

14. Install desired OPTICAL ACCESSORY pieces into the COVER RING and

re-thread the ACCESSORY RETAINER RING firmly. See Fig. 7.

*The COVER RING can accommodate three (3) accessories without the

ACCESSORY RETAINER RING or two (2) pieces with it.

*The ACCESSORY RETAINER RING may be used to lock the accessory.

For example, a linear spread lens or cross baffle can be locked in-place

into a desired orientation.

*Please note that not all accessories are compatible with each other and

with all lamps.

15. Regressed Lamp Ring/Snoot: (skip to Step 19 if not regressing the lamp)

The lamp ring may be installed in a regressed position only if a

SNOOT accessory is being used. See Fig. 8. If necessary, please see step

13 for instructions on SNOOT installation. To accomplish the regressed

lamp ring position set the COVER RING aside. Remove the lamp ring assy

by loosening the two (2) SET SCREWs in the GIMBAL BLOCKs.

16. Once loosened the lamp ring assy can be removed by grasping the

GIMBAL RING and turning

clockwise

until it releases from the GIMBAL

BLOCKs.

INSTALLATION INSTRUCTIONS

V90229-2

Avoid Fire or Electric Shock

COMBOLIGHT

LAMPHOLDER

Page 2 of 3

THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

*Installation Instructions for qualified electricians only.

*Install per National Electrical Code and local regulations.

*Read Installation Instructions completely before installation.

*Failure to follow Installation Instructions may void warranties.









GIMBAL BRACKET

(Standard Position)

SLOT

SET SCREW

SNOOT

GIMBAL RING

GIMBAL

BLOCK

17. Once removed, flip the two (2) GIMBAL BRACKETs around (180°) and

tighten the joint if necessary. See Fig. 9.

If necessary, please see Step 21 for gimbal tightening instructions.

18. Reinsert the lamp ring assembly by turning it

counter-clockwise

into the

SLOTs on the GIMBAL BLOCKs. Re-tighten the two (2) SET SCREWs

in the GIMBAL BLOCKs. The lamp ring assy should now be oriented in

the "up position". See Fig. 10.

BAYONET

SLOTS

COVER

RING

BACK RING

COVER RING

(AS INSTALLED)

GIMBAL BRACKET

(Rotated 180° to

"Down" Position)

19. To replace the COVER RING:

Push the COVER RING onto the BACK RING by lining up the

BAYONET SLOTS (see Fig. 11) with the two (2) PINs in the BACK RING.

Figure 10

Figure 11

Figure 12

Figure 9

20. Once lined up, push straight back until the COVER RING stops, then

while keeping the COVER RING pushed back, turn

clockwise

until it

pushes forward again slightly. See Fig. 12.

21. Gimbal tightening instructions:

The lamp ring is intended to give positive tension at the PIVOT JOINTS

so the lamp ring can be aimed by hand and held in place by tension.

*If a stronger, more secure lock is required then the PIVOT JOINTS (hex

screws) may be tightened

clockwise

with a hex wrench tool. See Fig. 6.

*Please note that in some conditions the COVER RING will need to be

removed to gain access to the inner PIVOT JOINTS.

INSTALLATION INSTRUCTIONS

V90229-3

Avoid Fire or Electric Shock

COMBOLIGHT

LAMPHOLDER

Page 3 of 3

THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

*Installation Instructions for qualified electricians only.

*Install per National Electrical Code and local regulations.

*Read Installation Instructions completely before installation.

*Failure to follow Installation Instructions may void warranties.









Inhaltsverzeichnis

Andere Cooper Lighting Beleuchtungsausrüstung Handbücher

Cooper Lighting

Cooper Lighting Halo Lazer LZR305 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo LZE800SL Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites LEM Bedienungsanleitung

Cooper Lighting

Cooper Lighting MT250PC Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L611 Bedienungsanleitung

Cooper Lighting

Cooper Lighting IRiS E3AASR Bedienungsanleitung

Cooper Lighting

Cooper Lighting ALL-PRO MST18920LES Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO Home MicroEdge HLB6 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites CC10 Bedienungsanleitung

Cooper Lighting

Cooper Lighting MS80 Bedienungsanleitung

Cooper Lighting

Cooper Lighting COMBOLIGHT CR220M70 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO MWP20FSUNVDBZ Bedienungsanleitung

Cooper Lighting

Cooper Lighting ATLANTIC PLUS Bedienungsanleitung

Cooper Lighting

Cooper Lighting McGraw-Edison Impact Elite LED Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO miniLUME LA5300 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO LAZER LZR204 Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE CFE-4 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting SURE-LITES HR87 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Portfolio LD4A Bedienungsanleitung

Cooper Lighting

Cooper Lighting MS185R Bedienungsanleitung

Cooper Lighting

Cooper Lighting AMETRIX ADY071480 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo Lazer LZR302 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung