Cooper Lighting Corelite Continua SQ4 Bedienungsanleitung
Lighting Solutions
A
D
G
B
EF
C
INS #
Brand Logo
reversed out of
black
INS #
IL524124EN
Installation Instructions - Continua SQ4 Suspended LED
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
ATTENTION - Receiving department: Note actual fixture description of any shortage or noticeable damage on delivery
receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be filed within 15 days
of delivery. All damaged material, complete with original packing must be retained.
WARNING
Risk of Fire, Electrical Shock, Cuts and or other
casualty hazards.This product must be installed in
accordance with the applicable installation code by
a qualified electrician or a person familiar with the
construction and operation of the product and the
hazards involved. Cooper Lighting Solutions assumes
no responsibility for claims brought about by improper
or careless installation or handling of this product.
WARNING
Risk of Fire and Electric Shock. If not qualified, consult
an electrician.
WARNING
All components must be used and installed as shown.
Failure to do so may result in injury.
Biscuit Aligner
Cross Cable
Bushing
Cable Adjuster Strain Relief
Cast joiner #8-18 x 5/8 HWH
Recommended Equipment:
• Hammer
• 1/4” nut driver
• Flathead screwdriver
• Scissors or sharp cutting blade
• Gloves
CAUTION
Edges May Cut. Handle with care.
CAUTION
Risk of Burn. Disconnect power and allow fixture to cool
before handling fixture.
CAUTION
Maximum distance between suspended mounting points
shall not exceed 12 feet.
NOTICE: Ground screw provided in proper location. Do not
relocate.
NOTICE: Minimum 90° supply conductors.
NOTE: Specifications and Dimensions subject to change
without notice.
2Cooper Lighting Solutions Installation instructions
Installation Instructions - Continua SQ4 Suspended LED
System Overview
SQ4 Joint Kit(s)
• (x4) Biscuit Aligners (A)
• (x2) Cast joiners (B)
• (x4) #8-18 x 5/8 HWH Screws (C)
NOTE: 1 kit required for each fixture-to-fixture joint
SQ4 Roll Lens
NOTE: 1 lens per run (up to 100’)
SQ4 End Kit(s)
• (x1) Die-Cast Endcap
• (x2) Cast joiners (B)
• (x4) #8-18 x 5/8 HWH Screws (C)
NOTE: 2 kits required for each run
(one for each end)
Fixture 1
Fixture 2, 3, 4...
Mount Spacing
Maximum distance of flexible mount location from end of unit: 1’ for 4’ unit, 1’ for 6’ unit, 2’ for 8’ unit 4’ for 12’ unit. Maximum
distance between mounting points shall not exceed 12 feet.
For installation at ceiling, see separate ceiling interface instructions.
AIRCRAFT CABLE CAN BE ADJUSTED INWARD.
MOUNTING POINTS EQUAL
FIXTURE LENGTHS 4’, 6‘, 8’ or 12’
POWER FEED
FIRST SECTION
FIRST SECTION
***CONSECUTIVE SECTIONS
***CONSECUTIVE SECTIONS
MOUNTING POINTS EQUAL
FIXTURE LENGTHS 4’, 6‘,8’ or 12’
2
3Cooper Lighting Solutions Installation instructions
Installation Instructions - Continua SQ4 Suspended LED
C
At each fixture end, secure Biscuit Aligners half way
into fixture end using hammer and install cast joiners.
IMPORTANT
Slide cross cable into fixture end. Mounting points
can be adjusted inward later as needed.
Bend tabs upward after inserting cross cable into fixture
in order to retain cross cable during installation.
Joining Hardware1Aircraft Cable at Fixture2
Power Drop
3
A
B
2X
D
E
Insert Supplied Bushing
Attach Strain Relief
as shown
4X
F
G
C
2X
4X E
4Cooper Lighting Solutions Installation instructions
Installation Instructions - Continua SQ4 Suspended LED
IMPORTANT: Ends of lens should overhang fixture
by ¼” at each end. Trim lens where necessary.
DO NOT UNDER-CUT.
Ensure all tabs are bent upward for joining and
making electrical connections. Close all tabs once
complete. Slide next fixture onto hanging fixture until
biscuit joiners engage. Make wiring connections and
push wires into housing prior to sliding the fixtures
firmly together. Once fixtures are together fasten
joiners using the provided #8-18 x 5/8 HWH screws.
Joining4
IMPORTANT: If conditions are dusty/dirty,
recommended practice is to keep lens roll(s) in
plastic packaging and install once conditions are
clean. Install roll lens using clean work gloves.
IMPORTANT: Energize fixture to test LEDs and
confirm they are all lit before beginning Roll Lens
install.
One person hold roll lens at one end of fixture (as
shown) while another person pulls lens through.
Roll Lens5
4
0.25”
C
2X
5Cooper Lighting Solutions Installation instructions
Installation Instructions - Continua SQ4 Suspended LED
C
2X
End Caps Sensor Side Mount (if applicable)
Sensor End Caps (if applicable)
6
7
Blowing off the Surface of the Lens
Additional Cleaning Methods
Dust and other loose contaminants should be blown
off before any other cleaning technique is employed.
Using compressed air over the entire lens is
recommended to prevent static buildup.
Fingerprints and large dust particles can be
removed by gently wiping the surface with a clean
microfiber cloth. If additional cleaning is required it
is recommended to use Clorox® wipes to remove
remaining contaminants by gently rubbing the
affected area and allowing to air dry.
Fixture Maintenance and Cleaning
Always follow recommended cleaning and
handling procedures when cleaning the lens. It can
be permanently damaged if cleaned or handled
improperly.
Secure endcaps to fixture using cast joiners. Close all
tabs once complete.
9
Wave Washer
Place Wave Washer on
the neck of the sensor
body
Tighten Decorative nut
while holding the Sensor
body in place
Decorative Nut
8
NOTE: Sensor connection
to supllied sensor wiring
should be made in the sensor
housing.
Warranties and Limitation of Liability
Please refer to www.cooperlighting.com/WarrantyTerms for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site www.cooperlighting.com/WarrantyTerms pour obtenir les conditions générales.
Garantías y Limitación de Responsabilidad
Visite www.cooperlighting.com/WarrantyTerms para conocer nuestros términos y condiciones.
FCC Statement
•This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received,
including
interference that may cause undesired operation.
Note: The grantee is not responsible for any changes
or modifications not expressly approved by the party
responsible for compliance. Such modifications could
void the user’s authority to operate the equipment.
Note: The equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off an on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment must be installed and operated in accordance
with provided instructions and the antenna(s) used for
this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons.
Lighting Solutions
Inhaltsverzeichnis
Andere Cooper Lighting Beleuchtungsausrüstung Handbücher
Cooper Lighting
Cooper Lighting FAIL-SAFE CFE-4 Series Bedienungsanleitung
Cooper Lighting
Cooper Lighting IRiS E3AASR Bedienungsanleitung
Cooper Lighting
Cooper Lighting Halo Lazer LZR302 Bedienungsanleitung
Cooper Lighting
Cooper Lighting MS185R Bedienungsanleitung
Cooper Lighting
Cooper Lighting HALO MWP20FSUNVDBZ Bedienungsanleitung
Cooper Lighting
Cooper Lighting ALL-PRO MST18920LES Bedienungsanleitung
Cooper Lighting
Cooper Lighting WaveLinx Lite Betriebsanleitung
Cooper Lighting
Cooper Lighting W35HPC Bedienungsanleitung
Cooper Lighting
Cooper Lighting Combolight Trimmed V90229-1T Bedienungsanleitung
Cooper Lighting
Cooper Lighting MT250PC Bedienungsanleitung
Cooper Lighting
Cooper Lighting LZR102 Bedienungsanleitung
Cooper Lighting
Cooper Lighting MIGHT LIGHT LED130 Bedienungsanleitung
Cooper Lighting
Cooper Lighting HALO ALL-PRO AL3050LPC Series Bedienungsanleitung
Cooper Lighting
Cooper Lighting RFM300 Bedienungsanleitung
Cooper Lighting
Cooper Lighting SURE-LITES CX Series Bedienungsanleitung
Cooper Lighting
Cooper Lighting ALL-PRO MST18920L Bedienungsanleitung
Cooper Lighting
Cooper Lighting MS245R Bedienungsanleitung
Cooper Lighting
Cooper Lighting Halo L611 Bedienungsanleitung
Cooper Lighting
Cooper Lighting COMBOLIGHT CR220M70 Bedienungsanleitung
Cooper Lighting
Cooper Lighting SURE-LITES SLX Series Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
