CPS PRO-SET CR700 Series Bedienungsanleitung

PRO-SET®

CR700 Series

TO BE OPERATED

BY QUALIFIED

PERSONNEL ONLY!

1 HP Commercial Refrigerant Recovery System

OPERATION MANUAL

TABLE OF CONTENTS

Specifications

Introduction

General Safety Instructions

Direct Liquid or Vapor Recovery Operation

Liquid Push-Pull Operation

Routine Maintenance

2-3

ENGLISH 1 - 5

SPECIFICATIONS

INTRODUCTION

Thank you for purchasing the CPS PROSET CR700 series unit. CPS is dedicated to give you the fastest and

most reliable equipment to meet all your commercial refrigerant recovery requirements. In doing this CPS

has integrated its latest technology and incorporated state of the art features while improving reliability and

speed. The CR700 incorporates an Exclusive CPS Designed Patent Pending compressor that maximizes speed

in both direct liquid and direct vapor recovery. The unit is equipped with a high airflow and high efficiency

condensing system to maximize vapor recovery speed. The CR700 also incorporates an automatic Low

Pressure shut off switch.

The CR700 is designed for servicing commercial and residential refrigeration systems. Simply follow the

quick start guide and turn it on. Once the recovery is complete, simply turn the center valve to the SELF-

CLEARING position. Now the unit is ready for the next type of refrigerant.

The PROSET CR700 series utilizes a 1 hp (0.85kW) patent pending oil-less compressor, non-restrictive

piston manifold valves, and high capacity condensing system.

The following are additional features:

• “On the Run” SELF-CLEARING valve. No need to turn off the unit when switching from recovery to

self-clearing.

•On board SUCTION and DISCHARGE gauges.

• 0 to 55 bar (800-psig) discharge gauge to handle R-410A.

• Small physical size.

• Automatic Low Pressure cutout switch.

• Integrated easy to use carrying handle and Safety bar.

•550 psig High Pressure cutout switch

• Easy and secure filter accesses. No dangling filters to be damaged.

Models

Compressor Type

Dimensions

Weight

Operating Temperature Range

Power Source

Power Consumption

Suction Pressure Gauge

Discharge Pressure Gauge

Filtration

Shut-Off Valves

Construction

Overload Protection

High Pressure Shut-Off

Refrigerants

Flow Rate

(at 60hz, reduce 15% for 50hz)

Direct Vapor

Direct Liquid

Push-Pull Liquid

-30” hg to 350 psig -1 to 34.5 bar -.1 to 3.5 MPa -30” hg to 350 psig

-76 cm hg to 35 kg/cm -100 kPa to 3450 kPa -76 cm hg to 35 kg/cm

0 to 800 psig 0 to 55 bar 0 to 5.5 MPa 0 to 800 psig

0 to 55 kg/cm 0 to 5500 kPa 0 to 55 kg/cm

Cleanable 100-mesh screen integrated into Suction Port

Both Suction and Discharge piston manifold valves

Heavy gauge aluminum chassis with High Density Polyethylene Case

15 amp 8 amp 15 amp 8 amp

38 bar (550 psig)

R-12, R-134a, R-401C, R-406A, R-500, R-401A

R-409A, R-401B, R-412A, R-411A, R-407D, R-22

R-411B, R-502, R-407C, R-402B, R408A, R-509

R-407A, R-404A, R-402A, R-507, R-407B, R-410A

Up to 43 kg/hr Up to 1.6 lb/min

Up to 271 kg/hr Up to 10 lb/min

Up to 542 kg/hr Up to 20 lb/min

850 W

115 V 50/60Hz 1 Ph 220-240 V 50/60 Hz 1 Ph 100 V 50/60 Hz 1 Ph 230 V 50/60 Hz 1 Ph

0°C (32°F) to 49°C (120°)

15.3 kg (34 lbs.)

20cm (8”) wide x 37cm (14.5”) long x 30.5cm (12”) high

1 HP Oil-less Reciprocating Compressor

CR700/CR700JUK* CR700E CR700J CR700S

* uses same gauges as CR700E

• Replaceable or cleanable filter cartridge.

• The Suction and Discharge shut-off valves. Easy to service if replacement required.

• Heavy-duty powder coated aluminum chassis surrounded by a tough High-Density Polyethylene case.

• Maintenance free Oil-less compressor

• Optional tank overfill sensor cord kit.

• patent pending

Low Pressure override switch to allow for continous operaton. To help you get a good start, please continue

to carefully read the balance of this manual. This manual contains important information on the proper

procedures for operating this equipment. Please pay close attention to the safety information, WARNING

and CAUTIONS provided throughout this manual. Always remember “SAFETY FIRST”.

GENERAL SAFETY INSTRUCTIONS

Only qualified service personnel should operate this unit. Most states, countries, etc… may require the

user to be licensed. Please check with your local government agency.

DANGER- the recovery tank used with this contains liquid refrigerant. Overfilling of the recovery tank may

cause a violent explosion resulting in severe injury or even death. As a minimum, please use a scale to

continuously monitor the recovery tank weight.

DANGER- Avoid breathing refrigerant vapors and lubricant vapor or mist. Breathing high concentration

levels may cause heart arrhythmia, loss of consciousness, or even cause suffocation.

DANGER- ELECTRICAL SHOCK HAZARD-Always disconnect power source when servicing this equipment.

DANGER- EXPLOSION RISK. Do not recovery flammable refrigerants

CAUTION- all hoses may contain liquid refrigerant under pressure. Contact with refrigerant may cause

frostbite or other related injuries. Wear proper personal protective equipment such as safety goggles and

gloves. When disconnecting any hose, please use extreme caution.

CAUTION- avoid breathing refrigerant vapors and/or lubricant mist. Exposure may irritate eyes, nose,

throat, and skin. Please read the manufacturers Material Safety Data Sheet for further safety information on

refrigerants and lubricants.

CAUTION- to reduce the risk of fire, avoid the use of extension cords thinner than NO. 14 awg. (1,5mm) to

prevent the overheating of this cord please keep length to a minimum.

CAUTION- do not use this equipment in the vicinity of spilled or open containers of gasoline or other

flammable substances. Make certain that all safety devices are functioning properly before operating the

equipment.

This equipment is intended for use of one refrigerant at a time until the Self-Clearing feature is used. Mixing

of different refrigerants will cause your recovered supply of refrigerant to become contaminated.

Note: It is very expensive to destroy mixed or damaged refrigerants.

DIRECT LIQUID OR VAPOR OPERATION

1. Connect the unit as shown in Diagram 1.

Note: The recovery tank must be rated for 38 bar.

2. Open the vapor valve on the Recovery Tank.

3. Open DISCHARGE valve on CR700.

Note: The Suction valve should be closed at this time.

4. Rotate the center valve to the “RECOVERY” position.

5. Push the Main Power Switch “ON”.

Note: If the unit fails to start, make sure there is no

suction pressure on the suction side of the unit. The

compressor is designed to start against high differential

pressures. Pressure on the suction side will reduce this

differential. Reset Circuit Breaker if tripped. Push the

LP Override Switch to the “ON” position.

6. Once unit has started, open the SUCTION valve on the CR700 to start the refrigerant flow.

7. The CR700 is designed to directly recover large amounts of liquid refrigerant. If during liquid recovery the

compressor begins to make a slugging or hammering noise, meter the incoming liquid by closing the

suction valve until the noise subsides.

8. The CR700 will automatically shut off* when a 10”hg vacuum is achieved. If the pressure rises (due to

boiling liquid refrigerant) the CR700 will resume operation.

9. After the CR700 has shut off, rotate the center valve to the SELF-CLEARING position. The CR700 will

resume operation automatically. The CR700 is now clearing out the condensor. The CR700 will

automatically shut off* when a 10”hg vacuum is achieved.

Note: If the LP override switch is set to “ON” position the unit will run continuously.

RECOVERY AND SELF-CLEARING ARE COMPLETE

LIQUID PUSH-PULL OPERATION

1. Connect the unit as shown in Diagram 2.

Note: The recovery tank must be rated for 38 bar.

2. Open the liquid and vapor valve on the Recovery Tank.

Note: The Suction valve should be closed at this time.

3. Open the DISCHARGE valve on CR700.

4. Rotate the center valve to the “SELF-CLEARING”

position.

5. Push the Main Power Switch “ON”

Note: If the unit fails to start, make sure there is no suction

pressure on the suction side of the unit. The compressor

is designed to start against high differential pressures.

Pressure on the siction side will reduce this differential.

Reset Circuit Breaker if tripped. Push the LP Override

Switch to the “ON” position.

6. Once unit has started, open the SUCTION valve on the CR700 to start the vapor refrigerant flow.

7. Monitor the optional inline sight glass for liquid refrigerant movement.

8. Once the liquid refrigerant is no longer present, close SUCTION valve. The CR700 will automatically shut

off* when a 10”hg vacuum is achieved.

9. Proceed to Direct Vapor Recovery Operation. (prior page)

Note: If the LP override switch is set to “ON” position the unit will run continuously.

ROUTINE MAINTENANCE

Filter Maintenance- the CR700 is equipped with a 100-mesh screen filter. This filter should be checked

periodically. A partially clogged filter will slow down the recovery rate of this unit.

Check the filter cartridge as follows:

• Use a 5/8” socket or boxed end wrench to loosen the suction port as shown in Figure 1.

• Once loose, remove the suction port- filter cartridge as shown in Figure 2.

• Either clean the current cartridge or replace with new cartridge.

• Inspect O-ring. Re-lubricate with compressor oil or equivalent.

• Place filter cartridge back into suction port fitting.

• Hand tighten this assembly back onto the CR700.

• Use a 5/8” socket or boxed end wrench to tighten 1/8 of a turn.

Do not over tighten, damage to the O-ring may occur.

• Check the connection for leaks.

Figure 1 Figure 2

Learn more about automotive A/C tools and equipment we have.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CPS Andere Handbücher

CPS

CPS CP330 Bedienungsanleitung

Beliebte Andere Handbücher anderer Marken

GO Industries

GO Industries 38017 Bedienungsanleitung

Cissell

Cissell 30LBCMAN2 Bedienungsanleitung

RIDGID

RIDGID K-60SP Bedienungsanleitung

Gage Bilt

Gage Bilt GB751SH-5 Bedienungsanleitung

OVE

OVE SIERRA 60 Bedienungsanleitung

ReelCraft

ReelCraft 7800 OLB21 Bedienungsanleitung

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Bedienungsanleitung

ROBLIN

ROBLIN DROP Benutzerhandbuch

EMG

EMG EMG-ACB BARREL Service-Handbuch

MiniSolar

MiniSolar MT-150 Bedienungsanleitung

Parkside

Parkside PSZ 250 B2 Bedienungsanleitung

ABB

ABB REM 610 Produkthandbuch

Parkside

Parkside 55992 Betriebsanleitung

Skyjacker

Skyjacker F250 Bedienungsanleitung

IBM

IBM IBM SYSTEM Z Installationsanleitung

Grech Motors

Grech Motors G28 Bedienungsanleitung

NOVAK

NOVAK BATTERY CARE SHEET Leitfaden

Telemotive

Telemotive blue PiraT Mini Benutzerhandbuch