Craftsman 486.24414 Bedienungsanleitung

Operator's Manual

For Garden Tractors with 23" Tires

Model No. 486.24414

CAUTION: Before using this product,

read this manual and follow all Safety

Rules and Operating Instructions.

CAUTION: DO NOT use this Dozer Blade

on Lawn Tractors or on Garden Tractors with

less than 23-inch diameter tires.

• Safety

,, Assembly

• Operation

• Maintenance

,, Parts

HVIPORTANT: For Missing Parts or

Assembly Questions Call 866-576-8388

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www,sears,com/craftsman

PRINTED IN U.S.A. FORM NO. 49810 (10/05)

SAFETY RULES ............................................................. 2

WARRANTY ................................................................... 2

CARTON CONTENTS .................................................... 8

FULL SIZE HARDWARE CHART ................................ 4-5

ASSEMBLY ................................................................ 6-13

OPERATION ................................................................. 14

SERVICE AND ADJUSTMENTS .................................. 15

MAINTENANCE ........................................................... 16

TROUBLESHOOTING .................................................. 16

STORAG E .................................................................... 17

ACCESSORIES ............................................................ 17

REPAIR PARTS iLLUSTRATiON ................................. 18

REPAIR PARTS MST ................................................... 19

PARTS ORDERING/SERVICE .................. BACK COVER

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.

Exercise caution at all times when using power equipment.

1. Read the tractor and dozer blade owners manuals and know how to operate your tractor before using the tractor with

the dozer blade attachment.

2. Never operate the tractor and dozer blade without wearing proper clothing suited to weather conditions and operation of

controls.

3. Never allow children to operate the tractor and dozer blade. Do not allow adults to operate without proper instructions.

4. Always begin with transmission in first (low) gear and gradually increase speed as required.

VLook for this symbol to point out important safety precautions, it means -- Attention!! Become

alert!! Your safety is involved.

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Dozer Blade fails due to a defect in

material or workmanship within one year from the date of purchase, call I°800°4°MYoHOME® to arrange for free repair (or

replacement if repair proves impossible).

If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179

The mode! number and serial numbers wil! be found on a

decal attached to the dozer blade.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

486.24414

i I

14\

18\

CARTON CONTENTS

1, Grip Assembly

2, Trigger with Cable

3, Left Side Plate

4, Right Side Plate

5, Blade Assembly

6, Attachment Rod

7, Handle Guide

8, Blade Pivot Bracket

9, Trip Spring (2)

10, Lift Link (2)

11_ Skid Shoe (2)

12, Lift Rod

13, Pivot Plate

14, Upper Lift Handle

15, Lower Lift Handle

16, Lift Bracket

17, Angle Lock Bar (2)

18, Frame Assembly

19, Handle Assembly

20, Contro! Cable

i- / B

i --4

I........ 3

I.......... i

I.........i

[........ t

I............ i

.........../1

l.............I Q

I / \

\\\\\\\

SHOWN FULL SiZE

,.K

J _\\\\

\\\

\\\\\\_ /

/\\\\

,¢

/.f ..........._ \\,I

I I

\\\ /

NOT SHOWN FULL SmZE

.... J

/MM NN OO

CONTENTS OF PARTSPACKAGE

REFo QTY. DESCRiPTiON REF. QTY. DESCRiPTiON

A 2 Hex Bolt, 1/2" x 2o3/4" V 11 Nylock Nut, 5/16"

B 2 Hex Bolt, 1/2" x 2" W 4 Hex Nut, 1/2"

C 2 Hex Bolt, 1/2" x 1ol/2" X 4 Hex Nut, 3/8"

D 2 Hex Bolt, 5/16" x 1o3/4" Y 2 Short Spacer

E 2 Hex Bolt, 3/8" x 1ol/4" Z 4 Lock Washer, 3/8"

F 4 Hex Bolt, 3/8" x 1" AA 1 Oval Screw, #10 x 1"

G 2 Hex Bolt, 5/16" x 3/4" BB 2 Washer

H 2 Hex Bolt, 3/8" x 3ol/2 CC 6 Washer, 1/2" Large

I 1 Shoulder Bolt DD 6 Washer, 5/8" SAE

J 6 Carriage Bolt, 3/8" x 1" EE 4 Washer, 1/2"

K 2 Carriage Bolt, 3/8" x 1ol/4" FF 4 Washer, 5/16"

L 6 Carriage Bolt, 5/16" x 1 GG 1 Cable Mount Bracket

M 1 Hex Bolt, 5/16" x 1ol/2" HH 2 Nylon Tie

N 2 Hex Bolt, 1/4" x 1ol/2" II 2 Clevis Pin

O 4 Cotter Pin JJ 2 Plastic Cap

P 4 Nylock Nut, 1/2" KK 7 Haircotter Pin

Q 10 Ny!ock Nut, 3/8" LL 2 Cable End Fitting

R 3 Nylock Nut, 1/4" MM 1 Extension Spring

S 1 Whizlock Hex Nut, 3/8" NN 1 Spring Pin

T 2 Hex Jam Nut, 5/16" OO 1 Plastic Grip

U 1 Long Spacer

TOOLSREQUIREDFORASSEMBLY

(1) 7/16"Wrench

(1) 1/2"Wrench

(1) 9/16"Wrench

(1) 3/4"Wrench

(1) AdjustableWrench

(1) PhillipsScrewdriver

(1) Hammer

, Removea!lpartsandhardwarepackagesfromthe

carton.Layoutpartsandhardwareandidentifyusing

theillustrationsonpages3and4.

NOTE: Notallofthesuppliedpartsandhardwarewillbe

neededforoneparticulartractor.Unneededitemsmaybe

discardedafterassemblyhasbeencompleted.

NOTE: Righthand(RH)andlefthand(LH)are

determinedfromtheoperator'spositionwhileseatedon

thetractor.

CAUTION: Donotbeginassembling

untilthetractorengine,mufflerandexhaust

deflectorhavebeenallowedtocooloff.

STEP 1: (SEE FIGURE 1)

, Look under the front of your tractor. If there is a single

mower deck suspension bracket located underneath

the middle of the front axle, continue on to step 2. If

your tractor does not have a mower deck suspension

bracket underneath the middle of the front axle, skip

to step 5 on page 7 for tractors with dua! suspension

brackets.

"_---_ BRACKET "--_--J"

FIGURE 1

iNSTRUCTiONS FORTRACTORS WITH SINGLE

FRONT DECK SUSPENSION BRACKET

STEP 2: (SEE FIGURE 2)

Remove the tractor hood. Refer to your tractor owners

manual for instructions on how to properly remove

the hood.

, Remove the browning shield from the front of the

tractor as shown. Hold onto the shield as you remove

the second bolt to prevent it from falling.

NOTE: Reinstall the browning shield before using your

tractor.

REMOVE

BROWNUNG SHUELD

FIGURE 2

STEP 3: (SEE FIGURE 3)

, Fasten the R.H. side plate (bend facing out) to the

front three holes indicated in the tractor frame. Use

three 3/8" x 1" carriage bolts (J) and three 3/8" nylock

nuts (Q). Fasten the rear of the side plate to the frame

using a 5/16" x 1" carriage bolt (L) and a 5/16" ny!ock

nut (V). If there is an engine mounting plate (shown

with dotted lines) that prevents the side plate from

resting flat against the tractor frame, use three large

1/2" washers (CC) as shims between the side plate

and the frame. Tighten all bolts. Repeat for the LH.

side plate.

, Reinstai! the browning shield removed in figure 2.

5/16" x t" ENGmNE LARGE 1/2"

CARRmAGE MOUNTmNG WASHER (CO)

BOLT (L) PLATE (IF

5/16" NYLOCK --_

NUT (V)

3/8" NYLOCK

NUT (Q) 318" x 1" CARRIAGE

BOLT (J)

FIGURE 3

STEP 4: (SEE FIGURE 4)

, Place a 1/2" washer (EE) and then a short spacer (Y)

onto a 1/2" x 1-1/2" hex bolt (C). Instal! the bolt in the

bottom hole at the front of the R.H. side plate and secure

it with a 1/2" nylock nut (P). Repeat for the L.H. side

plate,

Skip to step 8 on page 8.

STEP 6: (SEE FIGURE 6)

, Fasten the R.H. side plate (bend facing out) to the two

holes indicated in the tractor frame. Use two 3/8" x 1"

hex bolts (F) and 3/8" lock washers (Z). If the bolts

insert loosely into the tractor frame, use two 3/8" nylock

nuts (Q) on the inside of the frame. Repeat for the LH.

side.

1/2" X 1ol/2"

HEX BOLT (C)

SPACER (Y)

1/2" WASHER (EE) 1/2" NYLOCK

NUT (P)

3/8" NYLOCK NUT (Q)

(IF NEEDED)

3/8" x 1" \

HEX BOLT (F) "\ _j

FIGURE 4 FIGURE 6

iNSTRUCTiONS FOR TRACTORS WITH DUAL

FRONT DECK SUSPENSION BRACKETS

STEP 5: (SEE FIGURE 5)

, Remove bolts from holes shown in illustration if they

are present.

REMOVE BOLTS

FROM THESE HOLES

FIGURE 5

FRONT

SUSPENSmON

BRACKET

STEP 7: (SEE FIGURE 7)

, Place a 1/2" washer (EE) and then a short spacer (Y)

onto a 1/2" x 1-1/2" hex bolt (C). Install the bolt in the

bottom hole atthe front of the R.H. side plate and secure

it with a 1/2" nylock nut (P). Repeat for the LH. side

plate.

Go to step 8 on page 8.

HEX BOLT (C) SPACER (Y)

1/2" NYLOCK

1/2" WASHER (EE) NUT (P)

FIGURE 7

iNSTRUCTiONS FOR ALL TRACTORS

STEP 8: (SEE FIGURE 8)

', Install a 1/2" x 2" hex bolt (B) and two 1/2" hex nuts

(W) in the outer hole in each side of the pivot plate.

Temporarily adjust the hex nuts so that both bolt

heads extend about an inch and a half above the

pivot plate.

1/2" X2" BOLT (B)

)

112" HE× NUTS (W)' _

,©

FIGURE 8

STEP 9: (SEE FIGURE 9)

,, Assemble the round hook end of the angle lock

spring into the hole in the washer as shown,

WASHER

ANGLELOCK

SPRmNG

CHANNEUPIVOT

PLATE ASSEMBLY

FIGURE 9

STEP 10: (SEE FIGURE 10 and 11)

', Assemble the two angle lock bars together using a

3/8" x 1ol/4" carriage bolt (E) and a 3/8" nylock nut

(Q) in the top square hole& Do not tighten.

', Assemble the straight hook end of the angle lock

spring into the small holes in the angle lock bars.

Insert the lock bars down into the lock bar slot in

the channel pivot plate assembly.

3/8" X 1ol/4"

CARRIAGE BOLT

(TOP HOLE) (E) \

3/8" NYLOCK

ANGLELOCK

FRONT

LOCKBAR

SLOT

SPRRNG P_N

ANGLE LOCK

SPR_NG HOLE

CHANNEL/PIVOT

PLATE ASSEMBLY

FIGURE 10

Align the angle lock bars with the welded bracket

on the bottom of the channel, Use a hammer to

drive the spring pin (NN) through the angle lock

bars and into the slot in the welded bracket.

Tighten the nylock nut on the carriage bolt.

NOTE: The angle lock bars should pivot freely, When

they are pulled all the way back the pivot plate assembly

should be unlocked and free to pivot to the right or left

notches.

-_,_FRONT ANGLE

LOCK BARS

LOCK

BARS

1/4"' X l"'

SPRING PIN (NN}

FIGURE 11

STEP 11: (SEE FIGURE 12)

o Assemble a 3/8" x 1ol/4" carriage bolt (E) through

the cable mount bracket (GG) and then mount it

from the left side to the square holes in the angle

lock bars, Secure the bracket at the angle shown in

figure 14 with a 3/8" nylock nut (Q).

3/8" NYLOCK NUT (Q)

_ LOCK-_._I _ I /BRACKET (GG)/,

FIGURE 12

STEP 13: (SEE FIGURE 14)

Attach the cable end fitting (LL) and the long spacer

(U) to the left hand hole in the channel and lift bracket

using a 1/4" x 1ol/2" hex bolt (N) and 1/4" nylock nut

(R)=Tighten, keeping the cable end fitting aligned

with the threaded end of the cable.

CABLE MOUNT BRACKET 1/4" X 1-1/2"

HEX BOLT (N)

CABLE END

FiTTiNG (ll)

LONG SPACER(U)

CHANNEL

cKET

1/4" NYLOCK NUT (R)

STEP 12: (SEE FIGURE 13)

Select the control cable with two threaded ends,

Select the threaded end that has no rubber cap

or nuts and assemble a 5/16" hex jam nut (T)

approximately 3/4" onto the threads, Insert the

threaded end of the cable through the round hole

in the cable mount bracket (GG) and secure it with

another 5/16" hex jam nut (T). Tighten the second

nut while keeping the first nut in place.

Assemble the ball end of the cable wire up through

the hole in a cable end fitting (LL) and then slide it

back inside the curled edge of the fitting.

]5/16" BEX (T)

BALL END

FIGURE 13

FIGURE 14

STEP 14: (SEE FIGURE 15)

Attach the lift bracket to the right hand hole in the

channel, next to the long spacer, Use a 5/16" x 3/4"

hex bolt (G) and 5/16" nylock nut (V).

Attach the frame assembly to the channel assembly.

Fit one side of the frame assembly onto the 3/4" rod

of the channel and then fit the other side onto the rod.

Secure each side with a 3/4" washer (BB) and a 1/8"

x 1ol/4" cotter pin (O).

FRAME

5/16" X 3/4" BOLT (G)

ASSEMBLY

LIFT BRACKET

ROD

5116" NYLOCK

NUT (V)

314"WASHER (BB)

118" x 1-114"

COTTER PIN (O)

FIGURE 15

STEP 15: (SEE FIGURE 16)

, Attach the ends of the lift rod to the lift bracket on the

channel and the welded arm on the frame assembly.

Use two 1/2" washers (EE) and 1/8" x 1ol/4" cotter

pins (O).

STEP 17: (SEE FIGURE 18)

, Attach the skid shoes to the blade using four 5/18"

x 1" carriage bolts (L), 5/18" fiat washers (FF) and

5/18" nylock nuts (V), Do not tighten yet,

WELDED ARM

COTTER

PIN (0) _!

112" WASHER (EE) 1

LIFT ROD

FIGURE 16

5116" x 1" CARRIAGE

BOLT (L)

FIGURE 18

STEP 18: (SEE FIGURE 17)

, Assemble the blade pivot bracket to the pivot plate

assembly using two 3/8" x 1" bolts (F) and 3/8" nylock

nuts (Q),

Assemble the handle guide to the frame assembly

using a 5/16" x 3/4" bolt (G) and 5/16" ny!ock nut (V),

STEP 18: (SEE FIGURE 19}

, Align the channel pivot plate assembly behind the

blade and guide the ends of the mounting rod, one

end at a time, into the holes at the bottom of the

blade mount gussets. Secure the mounting rod with

two large hairpin cotters (KK).

3/8" NYLOOK /

NUT (Q) /

BLADE PIVOT

BRACKET

FIGURE 17

PIVOT PLATE

ASSEMBLY

HANDLE GUIDE 5116" X 3/4"

BOLT (G)

FIGURE 19

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 486.24537 Bedienungsanleitung

Craftsman

Craftsman 247.24019.1 Bedienungsanleitung

Craftsman

Craftsman 486.24441 Bedienungsanleitung

Craftsman

Craftsman 316.792440 Bedienungsanleitung

Craftsman

Craftsman 610.240842 Betriebsanleitung

Craftsman

Craftsman TRACTOR LIFT 610.246 Bedienungsanleitung

Craftsman

Craftsman ZT 7000 Bedienungsanleitung

Craftsman

Craftsman 247.240193 Bedienungsanleitung

Craftsman

Craftsman ZTS 7500 Bedienungsanleitung

Craftsman

Craftsman 358.795740 Bedienungsanleitung

Craftsman

Craftsman 486.243001 Bedienungsanleitung

Craftsman

Craftsman 358.795620 Bedienungsanleitung

Craftsman

Craftsman 19A30042791 Bedienungsanleitung

Craftsman

Craftsman 247.24019 Bedienungsanleitung

Craftsman

Craftsman 316.792520 Bedienungsanleitung

Craftsman

Craftsman 29918 - 17 in. Dual Rear Tine Tiller-CA... Bedienungsanleitung

Craftsman

Craftsman 610.24489 Bedienungsanleitung

Craftsman

Craftsman 358.795630 Bedienungsanleitung

Craftsman

Craftsman 358.795660 Bedienungsanleitung

Craftsman

Craftsman 486.248463 Bedienungsanleitung

Craftsman

Craftsman 486.24504 Bedienungsanleitung

Craftsman

Craftsman 486.244071 Bedienungsanleitung

Craftsman

Craftsman 486.24560 Bedienungsanleitung

Craftsman

Craftsman 421264 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung