Craftsman TRACTOR LIFT 610.246 Bedienungsanleitung

User Instructions

TRACTOR LIFT

Model Number 610.24600

Provides access to mower deck for easy

•

cleaning and service

Fits all 1985 through current models

•

of CRAFTSMAN front engine tractors

and Zero Turn Mowers

Can be fitted to most major front engine tractor brands

•

Adjustable arms for greater versatility

•

Extra heavy duty gauge steel construction

•

If you read and follow these instructions, this product can be

•

assembled in approximately 20 minutes

Assemble unit on cardboard to avoid scratches or damage to parts

•

Can easily be assembled by one person

•

All fasteners for this Tractor Lift can be purchased at Sears or any

•

hardware store

If there are any missing

•

parts, or if you have any

questions on assembly,

operation, maintenance

or safety, please call

1-800-652-6231

610.24600-REV B 3/08

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.sears.com/craftsman

Patent Pending

WARNINGS

Always use the stabilizer bar provided when using tractor lift.

•

Make sure stabilizer bar is properly in place before starting any

work on tractor.

Read and understand all safety and operating instructions

•

before using the tractor lift.

Never

allow anyone unfamiliar

with these instructions to use the tractor lift.

Read and understand all safety and operating instructions

•

provided by the tractor's manufacturer before using tractor lift.

Never

lay under the tractor or mowing deck.

•

When using lift, keep all bystanders, including children, away.

•

This tractor lift must be only used for lifting and lowering to

•

and from a level and stable surface.

Never

use in wet conditions.

•

Do not

attempt to lift the front and back of the tractor at the same

•

time.

Do not

use tractor lift as an automotive lift, or for any other use for

•

which it is not intended or designed.

If tractor lift is bowing while lifting or lowering your tractor, which

•

indicates an overload condition, remove the tractor immediately.

Do not

attempt to lift or lower any power equipment while motor is

•

running.

Never

engage blades while using tractor lift.

•

Always

disconnect spark plug wire from tractor before beginning

•

any work on tractor.

Do not

exceed the rated capacity of the tractor lift - 270#.

•

Failure to follow these warnings may result in property

•

damage and/or serious bodily injury.

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.

Page 2.

SAFETY INSTRUCTIONS

Be sure to read and follow all safety instructions and

•

warnings. Failure to follow these instructions may result in

damage to the product and/or serious personal injury.

Danger of serious personal injury exists. Serious personal

•

injury can occur when using a lifting device.

Never

attempt to ride any vehicle up or down the tractor lift.

•

Do not climb onto tractor while tractor is in the elevated position.

•

When working on the front of the tractor always place wheel

•

chocks in back of the rear wheels/tires.

Always raise and lower tractor lift in a controlled fashion; do not

•

allow the tractor to drop too quickly, damage could occur.

Make sure lifting arms are aligned and set to the proper distance apart

•

so that the equipment being loaded is well balanced on the lift.

Do not remove warning decals from product.

•

Before each use, always check for any worn, loose, or

•

damaged parts on the tractor lift. If any damage is present,

DO NOT USE THE TRACTOR LIFT

Periodically check the fasteners to make sure they are still

•

tight and in place.

Keep lift surface clean by occasionally cleaning with water and

•

any mild detergent.

Do not add to or try to modify the tractor lift in any way.

•

Any modifications will void any warranties.

Failure to abide by the warnings and read the safety instructions may

•

result in loss of load, damage to lift and/or property, serious personal

and/or fatal injury.

Tractor Lift can be used out of the box on all Craftsman tractors

with bumpers or brush guards. Tractor Lift mounting hardware is

provided if your tractor does not have a bumper or brush guard.

OPERATION

MAINTENANCE

Store unit in a clean dry place.

Recommended tire pressure - 30 PSI.

Before each use:

Always check tire pressure.

•

Always inspect unit for damage.

•

Always check fasteners for tightness.

•

TOOLS REQUIRED FOR ASSEMBLY

9/16" Wrench and/or Socket

Adjustable wrench

REF NO

QTY

PART NUMBER

DESCRIPTION

REF NO

QTY

PART NUMBER

DESCRIPTION

1 1 51001

Angle Frame Assembly

7L 1 410131

Tractor Mounting Bar - Left

2 1 51002

Handle Top

1 410132

Tractor Mounting Bar - Right

3 1 51003

Handle Bottom

8 1 51006

Stabilizer Bar

4 2 41009

Lift Tube Assembly

10 1 310031

Hardware Bag

6 1 51005 Lift Cross Tube 11 1 310041

Assembly Manual

Carton Contents

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.

Page 3.

26 22

24 28

Hardware Contents

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.

Page 4.

10.00000000

2.00000000

26 38

10.00000000

2.00000000

DETAIL I

SCALE 1 : 5.5

"X"

Remove,

add washer ( 24 ),

replace.

Step 1.

Step 2.

Tractor Lift can be used out of the box on all Craftsman tractors with bumpers or brush guards. Tractor Lift mounting hardware is provided. If

your tractor does not have a bumper or brush guard, follow the steps below:

Note: Left and Right sides are determined by standing behind tractor looking forward.

Step 1.

Remove existing bolt "X" and set aside. If tractor does not have

•

this bolt use supplied 3/8" x 1-1/4" bolt with 3/8 nylok nut.

Align holes in tractor mounting bars ( 7R & 7L ) to the front

•

left & right side frame holes of the tractor.

Insert hex head bolt ( 29 ) through inside front hole of frame,

•

through tractor mounting bar and secure with nylock nut ( 27 ).

Add flat washer ( 24 ) under head of bolt removed in earlier

•

step and reinsert through tractor mounting bar and tighten.

For LT1000 & LT2000 series tractors, use self-thread bolts

•

( 28 ) in place of bolt ( 29 ) and nut ( 27 ).

Step 2.

Push tube plugs ( 38 ) into each end of lift tube ( 6 ).

•

Slide lift tube through cut-out in tractor mounting bars and

•

center.

Pin lift tube in place with one hair pin cotter ( 26 ) on each side

•

of mounting bar.

Note: The mounting bars have been manufactured to attach to the

frames of most major front engine tractor brands. Additional

hardware has been included for attachment to non-Craftsman

brands.

Setting up Lift Mounting Hardware - Tractor Front

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.

Page 5.

Note: The higher the lift tube extensions (5)

are positioned, the harder the tractor will be to lift.

Push mower

Brush guard bumper

(can also be used for

front of Craftsman tractor)

Front of Craftsman Zero Turn

Front of Craftsman Tractors

Settings:

A. Push Mower

B. Brush guard / Bumper installed

C. Front of Craftsman Tractor

D. Front of Craftsman Zero Turn

Lift tubes come pre-assembled. Attach lift tube assemblies ( 4 ) to angle frame ( 1 ) using bolts ( 22 ), flat washers ( 24 ), split lock washers ( 23 )

•

and hex nuts ( 25 ).

Secure rear of lift tube assembly ( 4 ) to angle frame ( 1 ) using bolts ( 29 ), flat washers ( 24 ), split lock washers ( 23 ) and hex

•

nuts ( 25 ).

Note: Over-tightening receiver bolts ( 22 ) could cause damage to lift tubes ( 4 ).

Determining the width between lift tubes.

Assemble Tractor Lift

Attach Lift Tubes to Angle Frame

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.

Page 6.

224

25 1

Foot Bar Tube

Handle Top Tube

30 39

Peel off scuff pad (39)

backing and adhere to

back of handle.

IF HANDLE CANNOT BE

EASILY INSERTED, FLIP

HANDLE OVER AND

REINSERT.

Step 1. Attach handle bottom ( 3 ) to angle frame ( 1 ) using hex bolt ( 22 ),

flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25 ).

Step 2. Insert ring grip pin ( 30 ), as shown.

Step 3. Insert handle top ( 2 ) into handle bottom ( 3 ). Secure with hex

bolt ( 33 ), flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25 ).

Step 4. Place handle grips ( 37 ) onto handle top tube ( 2 ). A little

soapy water will help grip slide onto tube easily.

Assemble Tractor Lift

Attach Handle to Angle Frame

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.

Page 7.

Snap button

Foot bar tube

Step 1. Slide stabilizer bar ( 8 ) onto foot bar tube as shown.

Step 2. Press snap button and slide stabilizer bar against handle.

Step 3. Insert ring grip pin ( 30 ) through stabilizer bar and handle top.

Assemble Tractor Lift

Attach Stabilizer Bar

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.

Page 8.

30 8

Tube Handle

Snap Button

Turn 180

Figure 1 Figure 2

Snap Button

Step 3. Engaging Stabilizer Bar

Stabilizer bar MUST be engaged immediately after raising the tractor.

WARNING

: Failure to engage stabilizer bar may result in serious personal

injury and or property damage.

Remove ring grip pin ( 30 ) from tube handle. Press snap button

•

and slide stabilizer bar ( 8 ) from foot bar tube.

Turn stabilizer bar 180 degrees as shown at bottom of Figure 1.

•

Position stabilizer bar under base of unit between wheels.

•

Slide stabilizer bar back onto foot bar tube making sure the bar is

•

positioned back over snap button.

FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.

Page 10.

OPERATION

Using the Tractor Lift

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 486.244412 Bedienungsanleitung

Craftsman

Craftsman 358.795630 Bedienungsanleitung

Craftsman

Craftsman 610.24610 Bedienungsanleitung

Craftsman

Craftsman 29281 Bedienungsanleitung

Craftsman

Craftsman 610.24600 Bedienungsanleitung

Craftsman

Craftsman 486.24116 Bedienungsanleitung

Craftsman

Craftsman 486.24414 Bedienungsanleitung

Craftsman

Craftsman 358.795631 Bedienungsanleitung

Craftsman

Craftsman 316.792570 Bedienungsanleitung

Craftsman

Craftsman 917.248951 Bedienungsanleitung

Craftsman

Craftsman 41AJSS-C799 Bedienungsanleitung

Craftsman

Craftsman CMCA320 Bedienungsanleitung

Craftsman

Craftsman 45-04381 Bedienungsanleitung

Craftsman

Craftsman 486.24441 Bedienungsanleitung

Craftsman

Craftsman 25241 Bedienungsanleitung

Craftsman

Craftsman 486.24847 Bedienungsanleitung

Craftsman

Craftsman SNOW BLADE 486.24441 Bedienungsanleitung

Craftsman

Craftsman ZTS 7500 Bedienungsanleitung

Craftsman

Craftsman BUSHWACKER 517.795670 Bedienungsanleitung

Craftsman

Craftsman CMXGZBF7124336 Bedienungsanleitung

Craftsman

Craftsman 486.24536 Bedienungsanleitung

Craftsman

Craftsman 486.254072 Bedienungsanleitung

Craftsman

Craftsman 486.244411 Bedienungsanleitung

Craftsman

Craftsman 486.243291 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung