Craftsman 486.244412 Bedienungsanleitung

Operator's Manual

CRRFrSMRN°

42" OW LA

Model No. 486.244412 DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

CAUTION:

Before using this product, read

and follow all Safety, Assembly

and Operating Instructions

IMPORTANT: For Missing Parts or

Assembly Questions Call 866-576-8388

Safety

Assembly

Operation

Maintenance

Parts

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

PRINTED IN U.S.A. FORM NO. 42459 (2/10/12)

WARRANTY .................................................................... 2

SAFETY RULES ............................................................. 2

ACCESSORIES AND ATTACHMENTS ........................... 3

FULL SIZE HARDWARE CHART ................................... 3

CARTON CONTENTS .................................................... 4

ASSEMBLY ................................................................ 5-13

OPERATION ............................................................ 14-15

MAINTENANCE ............................................................ 15

SERVICE AND ADJUSTMENTS .................................... 16

STO RAG E................................................................. 16

TROU BLES HOOTI NG ............................................... 17

REPAIR PARTS ILLUSTRATION ...................................... 18

REPAIR PARTS LIST. ............................................... 19

PARTS ORDERING/SERVICE ............... BACK COVER

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the

equipment. Exercise caution at all times when using power equipment.

• Read the tractor and snow blade owner's manuals

and know how to operate your tractor before using

tractor with snow blade attachment.

Never operate tractor and snow blade without

wearing proper clothing suited to weather conditions

and operation of controls.

•Never allow children to operate tractor and snow

blade, and do not allow adults to operate without

proper instructions.

Always begin with transmission in first (low) gear and

gradually increase speed as conditions permit.

Look for this symbol to point out important safety precautions. It means--Attention!! Become

alert!! Your safety is involved. 1

CRAFTSMAN ONE YEAR FULL WARRANTY

FOR ONE YEAR from the date of purchase, this product is warranted against any defects in material or workmanship. A

defective product will be replaced free of charge.

For warranty coverage details to obtain free replacement, visit the web site: www.craftsman.com

This warranty is void if this product is ever used while providing commercial services or if rented to another person.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

DO NOT RETURN TO STORE for Missing Parts or Assembly Questions

Call 1-866-576-8388 Attachment Hotline

The model number and serial numbers will be found on

a decal attached to the snow blade.

You should record both the serial number and the

date of purchase and keep in a safe place for future

reference.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

486.244412

Theseandotheraccessoriesarerecommendedforusewithyourunit.Call1-800-4-MY-HOME®tofindoutiftheyareavailable.

Ifavailable,theymaybepurchasedatmostCraftsmanoutletsorbycalling1-800-4-MY-HOME®.

WHEEL WEIGHT TIRE CHAINS WEIGHT BRACKET

FOR DRAW BAR SNOW CAB

O P

REF.

PART NO. QTY.

46071 1

43648 1

43085 1

43001 14

710-0305 2

44326 2

47631 6

43350 6

712-0256 2

47189 3

47810 3

DESCRIPTION REF.

Hex Bolt, 1/4-20 x 3-1/4" L

Hex Bolt, 1/4-20 x 1-1/2" M

Hex Bolt, 5/16-18 x 1-1/2" N

Hex Bolt, 3/8-16 x 1" O

Carriage Bolt, 3/8-16 x 1-1/4" P

Bolt, Carriage 5/16-18 x 1" Q

Hex Bolt, 3/8" x 1" (Thd. Forming) R

Carriage Bolt, 3/8-16 x 1" S

Hex Jam Nut, 5/16" Fine Thread T

1/4" Nylock Hex Nut U

5/16" Nylock Hex Nut V

PART NO.

HA21362

R19172410

43070

43055

43010

1540-118

43003

44917

23658

46053

48106

QTY.

DESCRIPTION

i3/8"Nylock Hex Nut

Washer, 1/2" (Large)

3/8" Washer

Hairpin Cotter

Cotter Pin 1/8"x 1-1/4"

1/2" Washer

3/8" Lock Washer

Palnut, 3/8"

iSpacer, 5/8" Long

iSpacer, 1" long

Shoulder Bolt, 3/8 x .9"

Jj3

PARTS IN PACKAGES NOT SHOWN FULL SIZE

REF. QTY. DESCRiPTiON REF. QTY. DESCRiPTiON

2 Cable End Fitting 7 1 Blade Adjust Spring

1 Cable Mount Bracket 8 1 Plastic Grip

1 Angle Lock Spring 9 1 Grip Assembly

2 Nylon Tie 10 2 Angle Lock Bars

1 Spring Mount Rod 11 1 Blade Pivot Shaft

1 Channel Pivot Pin

CARTON CONTENTS (Loose Parts in Carton)

/14

24 ,\

REF. QTY. DESCRiPTiON REF. QTY. DESCRiPTiON

12 1 Hanger Bracket, L.H. 19

13 1 Hanger Bracket, R.H. 20

14 1 Pivot Support Bracket 21

15 2 Angle Support Bracket 22

16 1 Channel Assembly 23

17 1 Blade Assembly 24

18 1 Blade Pivot Rod

Lift Handle Tube

Lift Handle Rod

Cable

Slotted Angle Support Bracket

Quick Attach Bracket (RH)

Quick Attach Bracket (LH)

TOOLS REQUIRED FOR ASSEMBLY

(1)

Pliers

Hammer

Adjustable Wrench (or socket set)

9/16" Open End or Box End Wrench

7/16" Open End or Box End Wrench

1/2" Open End or Box End Wrench

NOTE: Not all of the supplied parts and hardware will

be needed for any one particular tractor. Unneeded items

may be discarded after assembly has been completed.

NOTE: Right hand (RH) and left hand (LH) are

determined from the operator's position while seated on

the tractor.

CAUTION: Do not begin assembling until

the tractor engine, muffler and exhaust

deflector have been allowed to cool off.

LOCATE MODEL LABEL OF TRACTOR

• Look under your tractor seat, locate the serial

number, and proceed to the step as shown.

£RgFT MgH

CONFORMS TO ANSi B71.1-2003 SAFETY STANDARDS

IIIil_llllllill

IIIIIIlllln,,,........,,,_llllllllllll

SERIALO00000AO00000

FORPAR1SANDSERVICECALL1-800-4MY-HOME

SEARS, ROEBUCK AND CO, Hoffm_ln Est_}_es, IL 60179

193653 ,j

917 MODEL TRACTORS

GO TO PAGE 5

INSTRUCTIONS FOR 917 MODEL TRACTORS

LOCATE MOWER SUSPENSION BRACKETS

Look under the front of your tractor.

If there is a single mower deck suspension

bracket located underneath the middle of the front

axle as shown in the image below, proceed to

INSTRUCTIONS FOR TRACTORS WITH SINGLE

FRONT DECK SUSPENSION BRACKET below.

If your tractor does not have a mower deck

suspension bracket underneath the middle of

the front axle, proceed to INSTRUCTIONS FOR

TRACTORS WITH DUAL FRONT SUSPENSION

BRACKETS on page 6.

MOWER DECK

SUSPENSION

BRACKET

FIGURE 1

INSTRUCTIONS FOR TRACTORS WITH SINGLE

FRONT DECK SUSPENSION BRACKET

STEP 1: (SEE FIGURE 2)

Remove the tractor hood. Refer to your tractor owners

manual for instructions on how to properly remove

the hood.

Remove the browning shield from the front of the

tractor as shown. Hold onto the shield as you remove

the second bolt to prevent it from falling.

£RnFT MRH

CONFORMS TO ANSi B71.1=2003 SAFETY STANDARDS

|pl==l ..... '="=l|l I

III|l_lllllllll

IIIIIIllll,,,.,......,=,,,_|l|llllllll

SERIAL 000000A000000

FOR P/\RTS AND SERVICE CALL 1-800-4MY-HOME

SEARS, ROEBUCK AND CO, Hoffman Estates, IL 60179 193653

247 MODEL TRACTORS

GO TO PAGE 8

NOTE: Reinstall the browning shield before using your

tractor.

FIGURE 2

BROWNING

SHIELD

STEP 2: (SEE FIGURE 3)

• Fasten the R.H. Side Plate (bend facing out) to the

front three holes in the tractor frame using three 3/8"

x 1" carriage bolts (H), three large 1/2" washers (M)

(see note) and three 3/8" nylock nuts (L). For the

rear hole, use a 5/16" x 1" carriage bolt (F), a large

1/2" washer (M) and a 5/16" nylock nut (K). Place the

washers between the tractor frame and the side plate.

Tighten all bolts. Repeat for L.H. side plate.

Reinstall the browning shield removed in figure 2.

• Proceed to INSTRUCTIONS FOR ALL 917 MODEL

TRACTORS on page 8.

NOTE: If there is an engine mounting plate (shown with

dotted lines) leave the large 1/2" washer (M) off the bolt

that goes through the plate.

5/16" x 1" CARRIAGE

BOLT (F) ENGINE

(SEE NOTE) MOUNTING

PLATE

5/16" NYLOCK

NUT (K)

3/8" NYLOCK

NUT(L)t

FIGURE 3

318"x 1" CARRIAGE

BOLT(H)

112"LARGE

WASHER(M)

INSTRUCTIONS FOR TRACTORS WITH DUAL

FRONT DECK SUSPENSION BRACKETS

iDENTiFY YOUR SUSPENSION BRACKETS

Compare your tractor to the illustrations shown below.

If your tractor resembles the top illustration, proceed

to iNSTRUCTiONS FOR TYPE A TRACTORS below.

If your tractor resembles the bottom illustration,

proceed to iNSTRUCTiONS FOR TYPE B

TRACTORS on page 7.

TYPE A

FRONT SUSPENSION

BRACKET

TYPE B

FRONT SUSPENSION

BRACKET

FIGURE 4

INSTRUCTIONS FOR TYPE A TRACTORS

STEP 1: (SEE FIGURE 5)

Remove any bolts found in the holes indicated in the

illustration.

REMOVE BOLTS FROM THESE HOLES

FIGURE 5

-,....FRONT

SUSPENSION

BRACKET

STEP 2: (SEE FIGURE 6)

o Attach the R.H. hanger bracket to the two front empty

holes on the right side of the tractor frame using two

new 3/8" x 1" hex bolts (D), 3/8" lock washers (R),

and 3/8" flat washers (N) as shown. For the rear hole,

use a 3/8" x 1" hex bolt (D), 3/8" lock washer (R)

and 3/8" flat washer (N) with a large 1/2" washer (M)

placed between the hanger bracket and the tractor

frame. Tighten. Repeat for the left side.

Proceed to INSTRUCTIONS FOR ALL 917 MODEL

TRACTORS on page 8.

318" FLAT

WASHER (N)

318"LOCK

WASHER (R)

3/8" x 1"

REX BOLT(D) _

112" LARGE

WASHER (M)

FIGURE 6

R.H. HANGER

BRACKET

INSTRUCTIONS FOR TYPE BTRACTORS

STEP 1: (SEE FIGURE 7)

Remove any bolts found in the holes indicated in the

illustration.

REMOVE BOLTS FROM

THESE HOLES

FRONT

SUSPENSION

BRACKET

FIGURE 7

STEP 2: (SEE FIGURE 8)

Attach the R.H. hanger bracket to the three holes

shown on the side of the tractor frame using three

3/8" x 1" hex bolts (D), 3/8" lock washers (R), 3/8"

fiat washers (N) and 1/2" large washers (M). Use 3/8"

nylock nuts (L) on inside of frame if bolts insert freely

into holes. Tighten.

Repeat for other side.

Proceed to iNSTRUCTiONS FOR ALL 917 MODEL

TRACTORS on page 8.

NOTE: Use special 3/8" x 1" thread forming bolts (G) in any

holes that are too small for regular bolts.

3/8" x 1" HEX BOLT (D)

(OR THREAD FORMING

BOLT (G) IF NEEDED)

3/8" LOCK

WASHER (R)

318" FLAT

WASHER (N)

3/8" NYLOCK NUT (L)

(IF NEEDED)

R.H. HANGER

BRACKET

FIGURE 8

112" LARGE

WASHER (i)

iNSTRUCTiONS FOR ALL 917 MODEL

TRACTORS

STEP 1: (SEE FIGURE 9)

• Assemble one angle support bracket to the topmost

set of holes in the hanger brackets using two 3/8" x

1" hex bolts (D) and 3/8" nylock nuts (L). Assemble

the second angle support bracket to the second from

the bottom set of holes in the hanger brackets using

two 3/8" x 1" hex bolts (D) and 3/8" nylock nuts (L).

Be sure the brackets are turned as shown. Do not

tighten yet.

_3/8 x 1

I I I I

REX BOLT(O)

3/8" NYLOCK -------'-_'@ /

NUT (L)

/ANGLE SUPPORT

BRACKET

FIGURE 9

STEP 2: (SEE FIGURE 10)

• Assemble the pivot support bracket to the angle

support brackets using four 3/8" x 1" hex bolts (D)

and four 3/8" nylock nuts (L). Do not tighten yet.

• Tighten the 4 bolts fastening the angle support

brackets to the hanger brackets.

• Tighten the 4 bolts fastening the pivot support

bracket to the angle support brackets.

• Proceed to BLADE ASSEMBLY FOR ALL

TRACTORS on page 10.

/318" NYLOCK

NUT (L)

PIVOT SUPPORT

BRACKET

FIGURE 10

iNSTRUCTiONS FOR 247 MODEL TRACTORS

STEP 1: (SEE FIGURE 11)

* Assemble one slotted angle support bracket to the

top set of holes in the quick attach brackets using two

3/8" x 1" hex bolts (D) and 3/8" nylock nuts (L). Do

not tighten

, Assemble the other slotted angle support bracket to

the bottom set of holes in the quick attach brackets

using two/8" x 1" hex bolts (D) and 3/8" nylock nuts

(L). Do not tighten.

NOTE: Be sure brackets are turned as shown.

3/8" x 1"

HEX BOLT (D)

3/8" NYLOCK

NUT(L)

FIGURE 11

STEP 2: (SEE FIGURE 12)

* Assemble the pivot support bracket to the slotted

angle support brackets using four 3/8" x 1" hex bolts

(D) and four 3/8" nylock nuts (L). Do not tighten yet.

* Tighten the 4 bolts fastening the slotted angle

support brackets to the quick attach brackets.

* Tighten the 4 bolts fastening the pivot support

bracket to the slotted angle support brackets.

3/8" x 1" /

HEX BOLT (D) 318"NYLOCK

NUT(L)

PIVOT SUPPORT

BRACKET

FIGURE 12

STEP3: (SEE FIGURE 13)

*Assemble a shoulder bolt (V) and a 3/8" nylock nut

(L) to the front bracket on each side of the tractor,

unless a shoulder bolt is already present.

3/8" NYLOCK NUT (L)

SHOULDER BOLT (V)

FIGURE 13

STEP 4: (SEE FIGURE 14)

• Pull out on the attachment pins on the hitch assembly

and swing the top of the pins down away from the

holes they were in.

Hook the hitch assembly onto the shoulder bolts in

the sides of the tractor frame.

Align the holes in the hitch assembly with the holes

in the tractor frame. Insert the attachment pins to lock

the hitch assembly in place.

Proceed to BLADE ASSEMBLY ALL TRACTORS on

page 10.

ATTACHMENT PiN

SHOULDER BOLT

FIGURE 14

BLADE ASSEMBLY FOR ALL TRACTORS

STEP 1: (SEE FIGURE 15)

• Assemble the two angle lock bars together as shown

in figure 6, so that all holes are aligned. Use one 3/8"

x 1-1/4" carriage bolt (E) and one 3/8" nylock nut (L).

Be sure to insert bolt from side indicated. Do not

tighten at this time.

Hold the angle lock bars so that the square holes are

at the top. insert the straight hook end of the angle

lock spring through the small middle hole in both

angle lock bars.

3/8" NYLOCK NUT (L)

3/8" x 1-1/4"

CARRIAGE BOLT (E)

O_ ANGLE LOCK BARS

ANGLE LOCK

SPRING

STEP 3: (SEE FIGURE 17)

Using a hammer, assemble a 3/8" palnut (S) onto one

end of the spring mount rod. insert the other end of

the spring mount rod through the pivot plate using the

rear set of holes. Support the assembled end of the

spring mount rod on a block of wood, and assemble

the remaining palnut onto the other end of the rod.

3/8" PALNUT

3/8" PALNUT(S)

SPRING

e_MOUNT

ROD

_'_ PIVOT

PLATE

FIGU RE 17 (Top View)

FIGURE 15 (Right Hand Side View)

STEP 2: (SEE FIGURE 16)

insert the round hook end of the angle lock spring up

through the hole in the spring mount bracket.

insertthe angle lock bars down through the slot in the

channel. Underneath the channel, place a 1" long spacer

(U) on each side of the angle lock bars and insert a 1/4"

x 3-1/4" bolt (A) through the channel, angle lock bars

and the spacers. Secure the bolt with a 1/4" nylock nut

(J). Tighten so that lock bars can pivot freely'.

At this time tighten the 3/8" carriage bolt and hex nut

previously assembled to angle lock bars.

NOTE: When the angle lock bars are pulled back in slot,

the pivot plate should unlock and be free to pivot to the

right or left position.

SPRING

PIVOT MOUNT

PLATE

BRACKET

CHANNEL

1/4" NYLOCK

NUT (J)

1"SPACERS

FIGURE16

ANGLE

LOCK

SPRING

"_"'-1/4" x 3-1/4"

REX BOLT (A)

(Right Hand Side View

STEP 4: (SEE FIGURE 18)

Assemble a 3/8" x 1-1/4" carriage bolt (E) through

the square hole in the cable mount bracket and

through the square hole in the angle lock bars. (The

carriage bolts should face in opposite directions.)

Using pliers hold the cable mount bracket in position,

angling down towards the L.H. hole in the channel as

shown in figure 15. Secure with a 3/8" nylock nut (L).

Tighten. Refer to the figure for the correct angle for

the cable mount bracket.

3/8" x 1-1/4"

CARRIAGE BOLT(E) .&_'_

ALIGN CABLE J_"_

MOUNT BRACKET _" /\_ ANGLE

WITH L.H. HOLE __----LOCK

3/8" NYLOCK

NUT (L) FRONT

FIGURE 18 (Right Hand Side View

Andere Handbücher für 486.244412

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 45-04381 Bedienungsanleitung

Craftsman

Craftsman ZT 7000 Bedienungsanleitung

Craftsman

Craftsman 358.796355 Bedienungsanleitung

Craftsman

Craftsman 486.244283 Bedienungsanleitung

Craftsman

Craftsman ZTS 7500 Bedienungsanleitung

Craftsman

Craftsman 944.361065 Bedienungsanleitung

Craftsman

Craftsman 19B30005791 Bedienungsanleitung

Craftsman

Craftsman 316.792570 Bedienungsanleitung

Craftsman

Craftsman 358.796360 Bedienungsanleitung

Craftsman

Craftsman 917.252492 Bedienungsanleitung

Craftsman

Craftsman C944.514323 Bedienungsanleitung

Craftsman

Craftsman 3One 917.257562 Bedienungsanleitung

Craftsman

Craftsman 19A70041791 Bedienungsanleitung

Craftsman

Craftsman 842.242560 Bedienungsanleitung

Craftsman

Craftsman 316.792520 Bedienungsanleitung

Craftsman

Craftsman 358.795630 Bedienungsanleitung

Craftsman

Craftsman 650 Series Bedienungsanleitung

Craftsman

Craftsman 486.24504 Bedienungsanleitung

Craftsman

Craftsman CMXGZBF71242131 Bedienungsanleitung

Craftsman

Craftsman CMXGZBF7124336 Bedienungsanleitung

Craftsman

Craftsman 358.796340 Bedienungsanleitung

Craftsman

Craftsman 486.24326 Bedienungsanleitung

Craftsman

Craftsman 247.24019 Bedienungsanleitung

Craftsman

Craftsman 610.24411 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung