Craftsman 358.796340 Bedienungsanleitung

Operator's Manual

ICRRFTgMRN°I

25cc/1.5 cu. in. 2-Cycle

GASOLINE HEDGE TRIMMER

Model No.

358.796340 - 22" Blade

• Safety

•Assembly

• Operation

• Maintenance

• Parts List

• Espar_ol, p. 15

WARNING:

Read and follow all Safety Rules and Operating

Instructions before first use of this product.

For answers to your questions about this product:

Call 7 am-7 pm, Mon-Sat; 10 am-7 pm, Sun

1-800-235-5878 (Hours listed are Central Time)

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

545140965 12/15/06

WarrantyStatement 2 Storage 9

SafetyRules 2 TroubleshootingTable 10

Assembly 4 EmissionsStatement 11

Operation 5 PartsList 13

Maintenance 7 Spanish 15

Service&Adjustments 8 PartsandOrdering BackCover

ONEYEARFULLWARRANTYONCRAFTSMAN®GASOLINEHEDGETRIMMER

Whenusedandmaintainedaccordingtotheoperator'smanual,ifthisproductfails

duetoadefectinmaterialorworkmanshipwithinoneyearfromthedateofpur-

chase,returnittoanySearsstore,SearsServiceCenter,orotherCraftsmanoutletin

theUnitedStatesforfreerepair(orreplacementifrepairprovesimpossible).

Thiswarrantyexcludes spark plug, air filter and blades, which are expendable

parts that can wear out from normal use in less than one year.

This warranty applies for only 30 days from purchase date if this product is used

for commercial or rental purposes.

This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

ADANGER: THIS POWER TOOL CAN

BE DANGEROUS! This unit can cause se-

rious injury including amputation or blind-

ness to the operator and others. The

warnings and safety instructions in this

manual must be followed to provide rea-

sonable safety and efficiency in using

this unit. The operator is responsible for

following the warnings and instructions in

this manual and on the unit. Never allow

children to use this tool.

_WARNING: Failure to follow all

Safety Rules and Precautions can re-

sult in serious injury.

KNOW YOUR UNIT

•Read your operator's manual care-

fully until you completely understand

and can follow all warnings and

safety rules before operating the unit.

• Restrict unit to users who understand

and will follow all warnings and safety

rules in this manual and on the unit.

PLAN AHEAD

_WARNING: Inspect the area be-

fore starting the unit. Remove all debris

and hard objects such as rocks, glass,

wire, etc. that can ricochet, be thrown,

or otherwise cause injury or damage

during operation.

• Always wear eye protection when op-

erating, servicing, or performing main-

tenance on unit. Wearing eye protec-

tion will help to prevent brush or debris

from being thrown or ricocheting into

eyes and face which can result in

blindness and/or serious injury. Eye

protection should be marked Z87.

• Wear hearing protection when using

this unit.

• Secure hair above shoulder length. Se-

cure or remove jewelry, loose clothing,

or clothing with loosely hanging straps,

ties, tassels, etc. They can be caught

in moving parts.

• Stay alert. Do not operate unit when

you are tired, ill, upset, or if you are

under the influence of alcohol, drugs,

or medication.

-2-

Safety Boots

Glasses

Blades move Allow blades to stop

_releasedmOmentarily before removing u

after the them from the cut.

trigger is.

WARNING:

Blades can throw objects violently.

•You can be blinded or injured.

• Wear safety glasses.

WARNING:

Hazard zone for thrown objects

• Blades can throw objects violently.

• Others can be blindedor injured.

• Keep people and animals 30 feet

(10 m) away.

WARNING:

Blades move momentarily after the

trigger is released.

• The blades can seriously cut you or

others.

• Allow blades to stop before

removing them from the cut.

• Keep children, bystanders, and ani-

mals away from work area a mini-

mum of 30 feet (10 meters) when

starting or operating unit.

If situations occur which are not cov-

ered in this manual, use care and good

judgment. If you need assistance, con-

tact your Sears Service Center or call

the Customer Assistance Helpline at

1-800-235-5878.

HANDLE FUEL WITH CAUTION

• Eliminate all sources of sparks or

flame (including smoking, open

flames, or work that can cause

sparks) in the areas where fuel is

mixed, poured, or stored.

• Mix and pour fuel in an outdoor area;

store fuel in a cool, dry, well ventilated

place; use an approved, marked con-

tainer for all fuel purposes.

• Do not smoke while handling fuel or

while operating the unit.

• Do not fill fuel tank while engine is

running.

• Make sure the unit is properly as-

sembled and in good operating con-

dition.

• Avoid spilling fuel or oil. Wipe up fuel

spills before starting the engine.

• Move at least 10 feet (3 meters)

away from fuel and fueling site before

starting engine.

• Always store gasoline in a container

approved for flammable liquids.

OPERATE YOUR UNIT SAFELY

_i DANGER: RISK OF CUT; KEEP

HANDS AWAY FROM BLADE - Blade

moves momentarily after the trigger is

released. Do not attempt to clear away

cut material when the blade is in mo-

tion. Make sure the ON/OFF switch is in

the OFF position, the spark plug wire is

disconnected, and the blade has

stopped moving before removing

jammed material from the cutting

blade. Do not grab or hold the unit by

the cutting blade.

• Inspect unit before each use for

worn, loose, missing, or damaged

parts. Do not use until unit is in

proper working order.

• Keep outside surfaces free from oil

and fuel.

• Never start or run engine inside a

closed room or building. Breathing

exhaust fumes can kill.

• Avoid dangerous environments. Do

not use in unventilated areas or

where explosive vapors or carbon

monoxide build up could be present.

• Be not overreach or use from unsta-

ble surfaces such as ladders, trees,

steep slopes, rooftops, etc. Keep firm

footing and balance at all times.

• Do not raise unit above your shoul-

ders; the cutting blade can come

dangerously close to your body.

• Always keep unit in front of your body.

Keep all parts of your body away from

the cutting blade=

-3-

• Keep the cutting blade and air vents

free from debris.

• Use only for jobs explained in this

manual.

MAINTAIN YOUR UNIT PROPERLY

_WARNING: Disconnect spark

plug before performing maintenance

except for carburetor adjustments.

• Have all maintenance and service

not explained in this manual per-

formed by a Sears Service Center.

• Do not use a cutting blade that is

bent, warped, cracked, broken, or

damaged in any other way. Have

worn or damaged parts replaced by

your Sears Service Center.

• Use only recommended Craftsman

cutting blades and replacement

parts; use of any other parts may

void your warranty and cause dam-

age to your unit.

• Empty fuel tank before storing the unit.

Use up fuel left in carburetor by starting

engine and letting it run until it stops.

• Hand carry the unit with the engine

stopped and the muffler and cutting

blade away from your body.

• Allow engine to cool, empty the fuel

tank, and secure the unit before stor-

ing or transporting it in a vehicle.

• Do not store the unit or fuel in a

closed area where fuel vapors can

reach sparks or an open flame from

hot water heaters, electric motors or

switches, furnaces, etc.

• Store the unit so the cutting blade

cannot accidentally cause injury.

• Store in a dry area out of reach of

children.

SAFETY NOTICE: Exposure to vibra-

tions through prolonged use of gaso-

line powered hand tools could cause

blood vessel or nerve damage in the

fingers, hands, and joints of people

prone to circulation disorders or abnor-

mal swelling. Prolonged use in cold

weather has been linked to blood ves-

sel damage in otherwise healthy

people. If symptoms occur such as

numbness, pain, loss of strength,

change in skin color or texture, or loss

of feeling in the fingers, hands, or

joints, discontinue the use of this tool

and seek medical attention. An

antivibration system does not guaran-

tee the avoidance of these problems.

Users who operate power tools on a

continual and regular basis must moni-

tor closely their physical condition and

the condition of this tool.

SPECIAL NOTICE: Your hedge trim-

mer is equipped with a temperature

limiting muffler and spark arresting

screen which meets the requirements

of California Codes 4442 and 4443. All

U.S. forest land and the states of Cali-

fornia, Idaho, Maine, Minnesota, New

Jersey, Oregon, and Washington re-

quire by law that many internal com-

bustion engines be equipped with a

spark arresting screen. If you operate

a hedge trimmer in a state or locale

where such regulations exist, you are

legally responsible for maintaining the

operating condition of these parts.

Failure to do so is a violation of the law.

For normal homeowner use, the muffler

and spark arresting screen will not re-

quire any service. After 50 hours of

use, we recommend that your muffler

be serviced or replaced by your Sears

Service Center.

CARTON CONTENTS

Check carton contents against the fol-

lowing list.

Model 358.796340

• Hedge Trimmer

• Scabbard

• 2-Cycle Engine Oil

NOTE: It is normal for the fuel filter to

rattle in the empty fuel tank.

ASSEMBLY

Your hedge trimmer is fully assembled;

no assembly is required.

-4-

KNOW YOUR HEDGE TRIMMER

READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

UNIT. Compare the illustrations with your unit to familiarize yourself with the location

of the various controls and adjustments. Save this manual for future reference.

Muffler ON/OFF

Switch

Spark Plug _. ,_/Throttle Lock

Hand Guard _- _ Throttle

Lock-out

Primer

ON/OFF SWITCH

The ON/OFF SWITCH is used to stop the

engine. To stop the engine, move the

switch to the OFF position.

CHOKE

The CHOKE helps to supply fuel to the

engine to aid in cold starting. Activate the

choke by moving choke lever to the de-

sired position. See STARTING YOUR EN-

GINE for complete starting information.

Trigger

BulbChoke Lever FuelMix Fill Cap

PRIMER BULB

The PRIMER BULB removes air from the

fuel lines and fills them with fuel. This

allows you to start the engine with few-

er pulls on the starter rope. Activate the

primer bulb by pressing it and allowing

it to return to its original form.

THROTTLE TRIGGER

The THROqq-LETRIGGER controls engine

speed. Squeeze the trigger for full speed

operation; release it for idle speed.

4t_WARNING: Muffler is very hot

during and after use. Do not touch the

muffler or allow combustible material

such as dry grass or fuel to do so.

BEFORE STARTING ENGINE

_WARNING: Be sure to read the

fuel information in the safety rules

before you begin. Ifyou do not

understand the safety rules, do not

attempt to fuel your unit. Call

1-800-235-5878.

FUELING ENGINE

_,WARNING: Remove fuel cap

slowly when refueling.

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good

quality synthetic 2-cycle air-cooled

engine oil. We recommend Craftsman

brand synthetic oil. Mix gasoline and oil

at a ratio of 40:1. A 40:1 ratio is

obtained by mixing 3.2 ounces of oil

with 1 gallon of unleaded gasoline=

Included with this hedge trimmer is a

3.2 ounce container of oil. Pour the

entire contents of this container into 1

gallon of gasoline to achieve the proper

fuel mixture. DO NOT USE automotive

oil or boat oil. These oils will cause

engine damage. When mixing fuel,

follow instructions printed on container.

Once oil is added to gasoline, shake

container momentarily to assure that

the fuel is thoroughly mixed. Always

read and follow the safety rules relating

to fuel before fueling your unit.

IMPORTANT

Experience indicates that alcohol

blended fuels (called gasohol or using

ethanol or methanol) can attract mois-

ture which leads to separation and

formation of acids during storage. Acid-

ic gas can damage the fuel system of

an engine while in storage.

To avoid engine problems, empty the

fuel system before storage for 30 days

or longer. Drain the gas tank, start the

engine and let it run until the fuel lines

and carburetor are empty. Use fresh

fuel next season. Never use engine or

carburetor cleaner products in the fuel

tank or permanent damage may occur.

See the STORAGE section for additional

information.

-5-

OPERATING INSTRUCTIONS

To maximize operating efficiency, do

not run the engine for longer than 30

seconds at a time at full throttle.

Releasing the trigger and allowing the

engine to briefly return to idle speed

(5-10 seconds) will be sufficient.

IMPORTANT POINTS

• Use the minimum throttle speed nec-

essary to effectively cut hedges for

optimal hedge trimmer performance.

• Never attempt to use this hedge trim-

mer to cut hedges that have any

branches with a diameter larger than

3/4".

OPERATING POSITION

Hearing

Protection Protection

1. Move the ON/OFF switch to the ON

position.

2. Engage the throttle lock as follows:

• press the throttle lock-out;

• squeeze and hold throttle trigger;

• press and hold throttle lock;

• release the throttle trigger

NOTE: Keep the throttle lock engaged

until the engine starts.

ON OFF

3. Slowly press the primer bulb 6 times.

4. Move the choke lever to the FULL

CHOKE position.

Primer Bulb Choke

Lever

STOPPING YOUR ENGINE

• To stop the engine, move the ON/OFF

switch to the OFF position.

BEFORE STARTING THE ENGINE

• Fuel engine. Move at least 10 feet (3

meters) away from the fueling site.

• Hold the unit on the ground in the

starting position as shown. Support

unit so the blade is off of the ground

and away from trees, bushes, on-

lookers, etc.

TL-.:/',,

,I_S/

STARTING A COLD ENGINE (or a

warm engine after running out of

fuel) Throttle Lock

X Throttle

Lock-out

Throttle

Trigger

Pull starter rope handle sharply until

engine sounds as if it is trying to run,

but do not pull rope more than 6

times.

Move the choke lever to the HALF

CHOKE position.

Pull starter rope sharply until the en-

gine runs, but no more than 6 pulls.

NOTE: If the engine doesn't start af-

ter 6 pulls (at the HALF CHOKE posi-

tion), check to make sure the ON/

OFF switch is in the ON position.

Move the choke lever to the FULL

CHOKE position and press the prim-

er bulb 6 times; pull the starter rope

2 more times. Move the choke lever

to the HALF CHOKE position and pull

the starter rope until the engine

runs, but no more than 6 more pulls.

If the engine still doesn't start, it is

probably flooded. Proceed to

STARTING A FLOODED ENGINE.

Once the engine starts, allow it to

run 10 seconds, then move the

chokelevertotheOFFCHOKEposi-

tion.Allowtheunittorunfor30more

secondsattheOFFCHOKEposition

beforesqueezingandreleasingthe

throttletriggertoreleasethethrottle

lock.NOTE:Ifenginedieswiththe

chokeleverintheOFFCHOKEposi-

tion,movethechokelevertothe

HALFCHOKEpositionandpullthe

ropeuntilengineruns,butnomore

than6pulls.

STARTING A WARM ENGINE

1. Move the ON/OFF switch to the ON

position.

2. Slowly press the primer bulb 6

times.

3. Move the choke lever to the HALF

CHOKE position.

4. Engage the throttle lock as directed

in STARTING A COLD ENGINE.

NOTE: Keep the throttle lock engaged

until the engine starts.

5. Pull starter rope sharply until engine

runs, but no more than 5 pulls.

6. Allow the engine to run 10 seconds,

then move choke lever to the OFF

CHOKE position.

7. Release the throttle lock by squeez-

ing and releasing the throttle trigger.

NOTE: If engine has not started, pull

starter rope 5 more pulls. If engine still

does not run, it is probably flooded. Pro-

ceed to STARTING A FLOODED ENGINE.

STARTING A FLOODED ENGINE

Flooded engines can be started by

placing the ON/OFF switch in the ON

position and the choke lever in the OFF

CHOKE position and engaging the

throttle lock as directed in the START-

ING A COLD ENGINE section; then, pull

the rope to clear the engine of excess

fuel. Starting could require pulling the

starter rope many times depending on

how badly the unit is flooded.

If the unit still doesn't start, refer to the

TROUBLESHOOTING TABLE or call

1-800-235-5878.

CUSTOMER RESPONSIBILITIES

_t WARNING: Ensure ON/OFF switch is in the OFF position and disconnect

the spark plug before performing maintenance except for carburetor adjust-

ments.

CARE &MAINTENANCE TASK WHEN TO PERFORM

Check for loose fasteners and parts Before each use

Check for damaged or worn parts Before each use

Inspect and clean unit and labels After each use

Clean air filter Every 5 hours of operation

Inspect muffler and spark arresting screen Every 50 hours of operation

Replace spark plug Yearly

Replace fuel filter Yearly

GENERAL RECOMMEN DATIONS

The warranty on this unit does not cov-

er items that have been subjected to

operator abuse or negligence. To re-

ceive full value from the warranty, the

operator must maintain unit as instruct-

ed in this manual. Various adjustments

will need to be made periodically to

properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

• Spark Plug Boot

• Air Filter

• Housing Screws

CHECK FOR DAMAGED OR

WORN PARTS

Contact Sears Service Center for re-

placement of damaged or worn parts.

• ON/OFF Switch - Ensure ON/OFF

switch functions properly by moving

the switch to the OFF position. Make

sure engine stops; then restart engine

and continue.

• Fuel Tank - Do not use unit if fuel tank

shows signs of damage or leaks.

INSPECT AND CLEAN UNIT AND

LABELS

• Before and after each use, inspect

complete unit for loose or damaged

parts.

-7-

• After each use, clean the unit and la-

bels using a damp cloth with a mild

detergent.

• Wipe off unit with a clean dry cloth.

CLEAN AIR FILTER

Air Filter

Cover

Air Filter Screw

A dirty air filter decreases engine per-

formance and increases fuel consump-

tion and harmful emissions. Always

clean after every 5 hours of operation.

1. Clean the cover and the area

around it to keep debris from falling

into the carburetor chamber when

the cover is removed.

2. Remove parts as illustrated.

NOTE: To avoid creating a fire hazard

or producing harmful evaporative emis-

sions, do not clean filter in gasoline or

other flammable solvent.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Add a few drops of oil to the filter;

squeeze filter to distribute oil.

6. Replace parts.

INSPECT MUFFLER AND SPARK AR-

RESTING SCREEN

_.WARNING: The muffler on this

product contains chemicals known to

the State of California to cause cancer.

As the unit is used, carbon deposits

build up on the muffler and spark ar-

resting screen. For normal homeowner

use, however, the muffler and spark ar-

resting screen will not require any ser-

vice. After 50 hours of use, we recom-

mend that your muffler and spark ar-

resting screen be serviced or replaced

by a Sears Service Center.

REPLACE SPARK PLUG

Replace spark plug each year to ensure

the engine starts easier and runs better.

Set spark plug gap at 0.025 inch. Ignition

timing is fixed, nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder

and discard.

3. Replace with Champion RCJ-6Y

spark plug and tighten securely with

a 3/4 inch socket wrench.

4. Reinstall the spark plug boot.

REPLACE FUEL FILTER

To replace fuel filter, drain unit by run-

ning it dry of fuel, then remove fuel cap/

retainer assembly from tank. Pull filter

from tank and remove it from the fuel

line. Install new fuel filter on fuel line;

reinstall parts.

Fuel Filter

Fuel Line

_WARNING: Disconnect the spark

plug before performing maintenance,

service or adjustments except for car-

buretor adjustments.

We recommend all service and adjust-

ments not listed in this manual be per-

formed by your Sears Service Center.

CARBURETOR ADJUSTMENT

,_WARNING: Keep others away

when making idle speed adjustments.

The blade will be moving during most

ofthis procedure. Wear your protective

equipment and observe all safety pre-

cautions. When making adjustments,

use a screwdriver short enough to

keep your hands behind the hand-

guard and away from the blade. After

making adjustments, the blade must

not move at idle speed.

The carburetor has been carefully set

at the factory. Adjustments may be

necessary if you notice any of the fol-

lowing conditions:

• Engine will not idle when the throttle

is released.

• The blade moves at idle.

-8-

Keep others away when making idle

speed adjustments. Make adjustments

with the unit resting on a level surface

free of debris that can be caught in the

hedge trimmer blade. Serious injury to

the operator and others can occur if the

carburetor is not properly adjusted.

Keep all parts of your body away from

the blade and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until

engine runs without blade moving (idle

too fast) or engine stalling (idle speed

too slow).

• Turn idle speed screw clockwise to

increase engine speed if engine

stalls or dies.

• Turn idle speed screw counterclock-

wise to decrease engine speed if the

blade moves at idle.

_WARNING: Recheck the idle

speed after each adjustment. The blade

must not move at idle speed to avoid se-

rious injury to the operator or others.

Idle Speed Screw

If you require further assistance or are

unsure about performing this proce-

dure, contact your Sears Service Cen-

ter or call our customer assistance help

line at 1-800-235-5878.

4BbWARNING: Perform the following

steps after each use:

• Allow engine to cool, and secure the

unit before storing or transporting.

• Store unit and fuel in a well ventilated

area where fuel vapors cannot reach

sparks or open flames from water

heaters, electric motors or switches,

furnaces, etc.

• Store unit with all guards in place.

Position unit so that any sharp object

cannot accidentally cause injury.

• Store unit and fuel well out of the

reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of sea-

son or if it will not be used for 30 days

or more.

If your unit is to be stored for a period

of time:

• Clean the entire unit.

• Store in a clean dry area.

• Clean all parts and check for damage.

Have damaged parts repaired or re-

placed by your Sears Service Center.

• Lightly oil external metal surfaces, in-

cluding the blade.

To oil the blade:

• Stop the engine and allow blade to

come to a complete stop.

• Ensure ON/OFF switch is in the OFF

position.

• Disconnect the spark plug wire.

• Apply a light machine oil along the

edge of the top strap as shown.

FUEL SYSTEM

Empty the fuel system before storage

for 30 days or longer. Drain the gas

tank, start the engine and let it run until

the fuel lines and carburetor are empty=

Use fresh fuel next season.

Under FUELING ENGINE in the OPERA-

TION section of this manual, see mes-

sage labeled IMPORTANT regarding

the use of gasohol in your engine.

Fuel stabilizer is an acceptable alterna-

tive in minimizing the formation of fuel

gum deposits during storage. Add stabi-

lizer to gasoline in fuel tank or fuel stor-

age container. Follow the mix instructions

found on stabilizer container. Run engine

at least 3 minutes after adding stabilizer.

Craftsman 40:1,2-cycle engine oil (air

cooled) is already blended with fuel

stabilizer. If you do not use this Sears

oil, you can add a fuel stabilizer to your

fuel tank=

-9-

ENGINE

• Remove spark plug and pour 1 tea-

spoon of 40:1,2-cycle engine oil (air

cooled) through the spark plug open-

ing. Slowly pull the starter rope 8 to

10 times to distribute oil.

• Replace spark plug with new one of

recommended type and heat range

(see REPLACE SPARK PLUG section).

• Clean air filter.

• Check entire unit for loose screws,

nuts, and bolts. Replace any dam-

aged, broken, or worn parts.

• At the beginning of the next season,

use only fresh fuel having the proper

gasoline to oil ratio.

OTHER

• Do not store gasoline from one sea-

son to another.

• Replace your gasoline can if it starts

to rust.

TROUBLESHOOTING TABLE

_, WARNING: Always stop unit and disconnect spark plug before perform-

ing all of the recommended remedies below except remedies that require

TROUBLE

Engine will not

start.

Engine will

not idle

properly.

Engine will not

accelerate,

lacks power.

or dies under

a load.

Engine

smokes

excessively.

Engine runs

hot.

operation of the unit.

CAUSE

1. ON/OFF switch in the OFF

position.

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. Fuel not reaching

carburetor.

6. Compression low.

1. Carburetor requires

adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. Air filter dirty.

2. Spark plug fouled.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

5. Compression low.

1. Choke partially on.

2. Fuel mixture incorrect.

3. Air filter dirty.

4. Carburetor requires

adjustment.

1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build-up on

muffler outlet screen.

REMEDY

1. Move ON/OFF switch to the ON

position.

2. See "Starting a Flooded Engine"

in Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel fitter; replace.

Check for kinked or spilt fuel tine;

repair or replace.

6. Contact Sears Service (see back

cover).

1. See "Carburetor Adjustment" in

Service and Adjustments Section.

2. Contact Sears Service (see back

cover).

3. Contact Sears Service (see back

cover).

1. Clean or repIace air filter.

2. Clean or replace plug

and regap.

3. Contact Sears Service (see back

cover).

4. Contact Sears Service (see back

cover).

5. Contact Sears Service (see back

cover).

1. Adjust choke.

2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter.

4. Contact Sears Service (see back

cover).

1. See "Fueling Engine" in Operation

section.

2. Replace with correct spark plug.

3. Contact Sears Service (see back

cover).

4. Contact Sears Service (see back

cover).

If situations occur which are not covered in this manual, use care and good

judgment. If you need assistance, contact your Sears Service Center or

call the Customer Assistance Helpline at 1-800-235-5878.

-10-

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 486.24414 Bedienungsanleitung

Craftsman

Craftsman 358.796355 Bedienungsanleitung

Craftsman

Craftsman 486.24839 Bedienungsanleitung

Craftsman

Craftsman 316.792510 Bedienungsanleitung

Craftsman

Craftsman 486.248474 Bedienungsanleitung

Craftsman

Craftsman TRACTOR LIFT 610.246 Bedienungsanleitung

Craftsman

Craftsman 247.24019.1 Bedienungsanleitung

Craftsman

Craftsman 486.243001 Bedienungsanleitung

Craftsman

Craftsman 610.24600 Bedienungsanleitung

Craftsman

Craftsman SNOW BLADE 486.24441 Bedienungsanleitung

Craftsman

Craftsman 316.792570 Bedienungsanleitung

Craftsman

Craftsman 45-04381 Bedienungsanleitung

Craftsman

Craftsman C944.514320 Bedienungsanleitung

Craftsman

Craftsman 320.74900 Bedienungsanleitung

Craftsman

Craftsman 610.24489 Bedienungsanleitung

Craftsman

Craftsman 421264 Bedienungsanleitung

Craftsman

Craftsman 917.24899 Bedienungsanleitung

Craftsman

Craftsman C944.514323 Bedienungsanleitung

Craftsman

Craftsman 486.24847 Bedienungsanleitung

Craftsman

Craftsman 486.242411 Bedienungsanleitung

Craftsman

Craftsman CMXMLBA5618A Bedienungsanleitung

Craftsman

Craftsman 19A30042791 Bedienungsanleitung

Craftsman

Craftsman 486.24250 Bedienungsanleitung

Craftsman

Craftsman ZTS 7500 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung