Craftsman 486.244283 Bedienungsanleitung

Owner's Manual

48" SNOW BLADE

Model No.

486.244283

PRINTED IN U.S.A.

FORM NO. 49828 (1/06)

•

Safety

•

Assembly

•

Operation

•

Maintenance

•

Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

CAUTION:

Before using this prod uct, read

this manual and fol low all Safe ty

Rules and Operating In struc tions.

STOP

DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

Most fasteners are readily available

through any hardware store

TABLE OF CONTENTS

MODEL NUMBER: 486.244283

SERIAL NUMBER: __________________

DATE OF PURCHASE: __________________

The model number and serial numbers will be found on a

decal attached to the snow blade.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

MAINTENANCE

...........................................................

SERVICE AND ADJUSTMENTS

..................................

STORAGE

....................................................................

TROUBLESHOOTING

..................................................

REPAIR PARTS ILLUSTRATION

.................................

REPAIR PARTS LIST

...................................................

PARTS ORDERING/SERVICE

..................

BACK COVER

Look for this symbol to point out important safety precautions. It means--

Attention!! Become

alert!! Your safety is involved.

SAFETY

SAFETY RULES

.............................................................

WARRANTY

...................................................................

ACCESSORIES

..............................................................

FULL SIZE HARDWARE CHART

...................................

CARTON CONTENTS

....................................................

ASSEMBLY

................................................................

6-13

OPERATION

............................................................

14-15

1. Read the tractor and snow blade owner's manuals and

know how to operate your tractor before using tractor

with snow blade attachment.

2. Never operate tractor and snow blade without wearing

proper clothing suited to weather conditions and

operation of controls.

3. Never allow children to operate tractor and snow

blade, and do not allow adults to operate without

proper instructions.

4. Always begin with transmission in ﬁ rst (low) gear and

gradually increase speed as required.

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.

Exercise caution at all times, when using power equipment.

ACCESSORIES AND ATTACHMENTS

WARRANTY

WHEEL

WEIGHT

TIRE CHAINS

WEIGHT BR

CKET

FOR DR

AW A

W CAB

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Snow Blade fails due to a defect in

material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair (or

replacement if repair proves impossible).

If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179

These and other accessories are recommended for use with your unit. Call 1-800-4-MY-HOME® to ﬁ nd out if they are available.

If available, they may be purchased at most Craftsman outlets or by calling 1-800-4-MY-HOME®.

HARDWARE PACKAGE CONTENTS

(SHOWN FULL SIZE)

REF. QTY. DESCRIPTION

A 1 Hex Bolt, 1/4" x 3-1/4" LG.

B 1 Hex Bolt 1/4" x 1-1/4"

C 4 Hex Bolt, 5/16" x 1"

D 1 Hex Bolt, 5/16" x 1-1/2"

E 2 Hex Bolt, 3/8" x 1"

F 1 Hex Bolt, 1/2" x 1-3/4"

G 4 Carriage Bolt 3/8" x 1-1/4"

H 18 Carriage Bolt, 3/8" x 1"

I 3 Nylock Nut, 1/4"

J 5 Nylock Nut, 5/16"

K 22 Nylock Nut, 3/8"

L 1 Nylock Nut, 1/2"

M 4 Hex Jam Nut, 5/16"

N 2 Palnut, 3/8"

O 2 Lock Washer, 3/8"

P 3 Washer 1/2"

Q 1 Clevis Pin, 5/8" x 1-3/4"

R 2 Clevis Pin, 1/2" x 1"

S 1 Spacer, 5/8" LG.

T 2 Spacer, 1" LG.

U 3 Hairpin Cotter, Large

V 4 Hairpin Cotter, Small

W 2 Cotter Pin 1/8" x 1-1/4"

A B

E F G H

REF. QTY. DESCRIPTION

1 1 Long Hanger Bracket

2 1 Short Hanger Bracket

3 1 Rear Mounting Bracket

4 1 Pivot Support Bracket

5 1 Thrust Channel

6 1 Channel Assembly

REF. QTY. DESCRIPTION

PARTS IN HARDWARE PACKAGES NOT SHOWN FULL SIZE

CARTON CONTENTS

(Loose Parts in Carton)

REF. QTY. DESCRIPTION

1 1 Long Hanger Bracket

2 1 Short Hanger Bracket

3 1 Rear Mounting Bracket

4 1 Pivot Support Bracket

5 1 Thrust Channel

6 1 Channel Assembly

REF. QTY. DESCRIPTION

1 1 Long Hanger Bracket

2 1 Short Hanger Bracket

3 1 Rear Mounting Bracket

4 1 Pivot Support Bracket

5 1 Thrust Channel

6 1 Channel Assembly

REF. QTY. DESCRIPTION

AA 2 Cable End Fitting

BB 1 Cable Mount Bracket

CC 1 Angle Lock Spring

DD 2 Nylon Tie

EE 1 Spring Mount Rod

FF 1 Channel Pivot Pin

7 1 Blade Assembly

8 1 Blade Pivot Rod

9 1 Lift Handle Tube

10 1 Lift Handle Rod

11 2 Rear Support Channel

12 1 Cable

AA BB

HH II

GG 1 Blade Adjust Spring

HH 1 Plastic Grip

II 1 Grip Assembly

JJ 2 Angle Lock Bar

KK 1 Blade Pivot Shaft

LL 2 Frame Bracket

MM 1 Rear Locating Bracket

(1) Pliers

(1) Hammer

(1) Adjustable Wrench (or socket set)

(1) 9/16" Open End or Box End Wrench

(2) 7/16" Open End or Box End Wrench

(2) 1/2" Open End or Box End Wrench

TOOLS REQUIRED FOR ASSEMBLY

REMOVAL OF PARTS FROM CARTON

•

Remove the loose parts and the hardware packages

from the carton. Lay out all parts and hardware and

identify using the illustrations on pages 4 and 5.

IMPORTANT:

You will not use all of the parts or hardware

supplied with your blade. Dispose of unused parts or

hardware after you have ﬁ nished assembling the blade.

CAUTION:

Do not

begin assembling

until the tractor engine, mufﬂ er and exhaust

deﬂ ector have been allowed to cool off.

TRACTOR PREPARATION

•

Allow engine, mufﬂ er and exhaust deﬂ ector to cool

before beginning.

•

Refer to tractor owner's manual to remove mower

deck or any other attachment you may have mounted

to your tractor. Mark and save all removed parts.

IMPORTANT:

Right hand (R.H.) and left hand (L.H.) are

determined from the operators position while seated on

the tractor.

STEP 1: (SEE FIGURE 1)

•

Look

under the front of your tractor

Look under the front of your tractorLook

. I

f there is a single

mower deck suspen

sion bracket located

underneath

the mi

le of the front axle, continue

on to step

not

, skip to step 7 on page 8 for tractors with dual

mower deck suspension brackets.

MOWER DECK

SUSPENSION

BRACKET

FIGURE 1 - SEARS TRACTOR SHOWN

3/8" LOCK WASHER (O)

3/8" X 1" HEX BOLT (E)

FRAME BRACKET

3/8" NYLON

LOCK NUT (K)

3/8" X 1"

CARRIAGE BOLT (H)

FIGURE 2 - SEARS TRACTOR SHOWN

REMOVE BROWNING

SHIELD ON SEARS

TRACTORS

MOUNTING

HOLES ON

SEARS TRACTORS

FRAME

BRACKET

FIGURE 3 - SEARS TRACTOR SHOWN

STEP 3: (SEE FIGURE 3)

•

Attach

a frame bracket to each sid

e of the tractor

frame. On Sears tractors use a 3/8" x 1" hex bolt

(E) and 3/8" lock washer (O) in the lower hole and a

3/8" x 1" carriage bolt (H) and 3/8" nylock nut (K) in

the upper hole of each frame bracket. Leave out the

upper bolt if there is no hole in the tractor frame.

not tighten.

For other brand tractors use the bolts

and nuts shown in the illustrations on page 9.

• On Sears tractors re-attach

the bro

wning shield

STEP 2: (SEE FIGURE 2)

•

Use ﬁ gure 2 to help i

dentify the mounting holes for

Sears tractor frames.

For other brand tractors

, identify

the two mounting holes by p

lacing a frame bracket

against the tractor frame

in front

the front axle and

ﬁ nding two holes in the tractor frame that align with

two of the holes in the frame bracket

he bracket can

be ﬂ

ipped over to reverse the

hole pattern.

efer also

to the illustrations on page

• Remove any bolts found in the mounting holes.

• On Sears tractors, remove the browning shield from

the front of the tractor as shown.

IMPORTANT:

Be sure to reattach

the browning shield in

step 3

INSTRUCTIONS FOR TRACTORS WITH SINGLE

FRONT DECK SUSPENSION BRACKETS

OPERATION

FIGURE 6

3/8" x 1-1/4"

CARRIAGE BOLT (G)

3/8" NYLOCK NUT (K)

HANGER BRACKETS

Ends down when "H" is 6" or less

Ends up when "H" is more than 6"

FRONT PLATE

3/8" x 1-1/4"

CARRIAGE BOLT (G)

3/8" NYLOCK NUT (K)

LONG HANGER

BRACKET

12-1/4"

SHORT HANGER

BRACKET

FIGURE 4 - SEARS TRACTOR SHOWN

STEP 4:

(SEE FIGURE 4)

This step is for Sears tractors only.

If you have a

tractor brand other than Sears, skip to step 5.

•

Stack the short Hanger Bracket on top of the long

Hanger Bracket with the ends of the brackets pointing

up. Align the ﬁ rst and third slots in both brackets with

the middle set of slots in the thrust channel as shown.

• Fasten the brackets to the thrust channel using

two 3/8" x 1-1/4" carriage bolts (G) and 3/8" nylock

nuts (K). Spread the brackets so that the ends are

approximately 12-1/4" apart, measured from the

outside.

Do not tighten.

•

Skip to step 9 on page 10.

JOHN DEERE LT TRACTOR

FIGURE 5 - JOHN DEERE TRACTOR LT SHOWN

STEP 5:

(SEE FIGURE 5)

This step is for tractor brands other than Sears.

If you have a Sears tractor, skip to step 9 on page 10.

• Measure the distance from the center of the frame

brackets to the front of the tractor frame. This will be

referred to as distance "L" in step 6.

• Measure to determine which of the two holes at

the bottom of the Frame Bracket is closest to being

6" from the ground. The height of this hole will be

referred to as distance "H" in step 6.

•

Measure the inside distance between the Frame

Brackets. This distance will be referred to as distance

"W" in step 6.

STEP 6:

(SEE FIGURE 6 AND THE ILLUSTRATIONS

ON PAGE 9)

This step is for tractor brands other than Sears.

If you have a Sears tractor, skip to step 9 on page 10.

•

Refer to the illustrations on page 9 for examples of

how to attach the Hanger Brackets on various tractors.

•

Select the set of slots in the top of the Thrust Channel

that will postion the channel's front plate slightly out in

front of the tractor frame. The distance from the slots

to the front plate must be slightly greater than the

distance

"L"

in step 5.

•

Hold the Hanger Brackets with the ends pointing up.

Stack the short Hanger Bracket on top of the long

Hanger Bracket. If distance

"H"

measured in step 5

was less than 6", hold the brackets together and ﬂ ip

them over so that the ends point down.

•

Slide the Hanger Brackets apart so that the overall

length is slightly less than distance

"W"

measured

in step 5. Center the Hanger Brackets on top of the

Thrust Channel and attach them to the selected slots

using two 3/8" x 1-1/4" carriage bolts (G) and 3/8"

nylock nuts (K).

Do not tighten.

•

Proceed to step 9 on page 10.

FIGURE 7 - SEARS TRACTOR SHOWN

SEARS (LT) TRACTOR FRAME

SUSPENSION

BRACKET

UND

INSTRUCTIONS FOR TRACTORS WITH DUAL

FRONT DECK SUSPENSION BRACKETS

STEP 8:

(SEE FIGURE 8 AND THE ILLUSTRATIONS

ON PAGE 9)

•

Refer to the illustrations on page 9 for examples of

how to attach the Hanger Brackets on various tractors.

•

Select a set of slots in the top of the Thrust Channel

that will position the front plate slightly out in front of

the tractor frame. The distance from the slots to the

front plate must be slightly greater than the distance

"L"

in step 7.

•

Hold the Hanger Brackets with the ends pointing up.

Stack the short Hanger Bracket on top of the long

Hanger Bracket. If distance

"H"

measured in step 7

was less than 6", hold the brackets together and ﬂ ip

them over so that the ends point down.

•

Slide the Hanger Brackets apart so that the overall

length is slightly less than distance

"W"

measured

in step 7. Center the Hanger Brackets on top of the

Thrust Channel and attach them to the selected slots

using two 3/8" x 1-1/4" carriage bolts (G) and 3/8"

nylock nuts (K).

Do not tighten.

•

Proceed to step 9 on page 10.

3/8" x 1-1/4"

CARRIAGE BOLT (G)

3/8" NYLOCK NUT (K)

HANGER BRACKETS

Ends down when "H" is 6" or less

Ends up when "H" is more than 6"

FRONT PLATE

FIGURE 8

STEP 7:

(SEE FIGURE 7)

•

Locate the Mower Deck Suspension Brackets on each

side at the front of the tractor frame. A Sears tractor

is shown below. For examples of brackets on other

tractors see the illustrations on page 9.

• Measure the distance from the center of the deck

attachment hole in the Mower Deck Suspension

Brackets to the front of the tractor frame. This will be

referred to as distance "L" in step 8.

•

Measure the height above the ground of the deck

attachment hole in the Mower Deck Suspension

Brackets. The height of this hole will be referred to as

distance "H" in step 8.

•

Measure the inside distance between the Mower

Deck Suspension Brackets. This will be referred to as

distance "W" in step 8.

SEARS LAWN

TRACTORS

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN

MIDDLE SET OF SLOTS IN THRUST CHANNEL

9.75"

SEARS GARDEN

TRACTORS

12"

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN

MIDDLE SET OF SLOTS IN THRUST CHANNEL

MTD - LAWN TRACTORS

WITH FAST ATTACH FEATURE

13"

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

MTD - GARDEN TRACTORS

WITH FAST ATTACH FEATURE

13"

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

MTD GARDEN

TRACTORS

13"

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

MTD LAWN

TRACTORS

13"

FRAME

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

5/16" x 1"

HEX BOLT

MURRAY TRACTORS

8.5"

TRACTOR

SUSPENSION

BRACKET

LOCATE HANGER BRACKETS IN REAR

SET OF SLOTS IN THRUST CHANNEL

FORWARD SLOTS MAY BE USED ON

SOME MURRAY TRACTORS

JOHN DEERE SABRE

13"

FRAME

BRACKET

3/8" x 1"

CARRIAGE

BOLT

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

12.75"

3/8" x 1"

HEX BOLT

3/8" x 1"

CARRIAGE

BOLT

LOCATE HANGER BRACKETS IN

MIDDLE SET OF SLOTS IN THRUST CHANNEL

FRAME

BRACKET

SEARS TRACTORS WITH

CENTER SUSPENSION BRACKET

JOHN DEERE LT

13"

FRAME

BRACKET

LOCATE HANGER BRACKETS IN FRONT

SET OF SLOTS IN THRUST CHANNEL

5/16" x 1"

HEX BOLT

STEP 12:

(SEE FIGURE 12)

•

Place the rear of the Thrust Channel between the

two Rear Support Channels. Install four 3/8" x 1"

carriage bolts (H) and 3/8" nylock nuts (K) using the

most widely spaced holes that are aligned with slots.

Finger tighten only.

•

If the Rear Support Channels bump against bottom

of the tractor, reattach the rear of the channels to a

lower set of holes in the Rear Mounting Bracket. If

there is more clearance than necessary between the

Rear Support Channels and the bottom of the tractor,

reattach the rear of the channels to a higher set of

holes in the Rear Mounting Bracket.

• Spread the Hanger Brackets apart as far as possible

and center the Thrust Channel under the tractor.

•

Tighten

all bolts and nuts installed up to this point.

• Measure the height of the front plate on the Thrust

Channel. If it is not 4" to 5" above the ground, reinstall

the clevis pins in the Hanger Brackets to a higher or

lower hole position to attain the correct height.

STEP 13:

(SEE FIGURE 13)

•

Assemble the pivot support bracket to the front of the

Thrust Channel using four 3/8" x 1" carriage bolts (H)

and four 3/8" nylock nuts (K). Make sure the bracket is

straight and then

tighten.

FIGURE 10

FIGURE 13 - SEARS TRACTOR SHOWN

FIGURE 9

REAR SUPPORT

CHANNELS

REAR MOUNTING

BRACKET

REAR LOCATING

BRACKET

3/8" X 1"

CARRIAGE BOLT (H)

3/8" NYLOCK NUT (K)

TRACTOR

DRAWBAR

5/8" X 1-3/4"

CLEVIS PIN (Q)

LARGE

HAIRPIN

COTTER (U)

REAR MOUNTING

BRACKET

REAR LOCATING

BRACKET

REAR SUPPORT

CHANNEL

STEP 10:

(SEE FIGURE 10)

•

Slide the Rear Support Channels under the rear of

the tractor. Attach the Rear Mounting Bracket to the

Tractor Drawbar using the 5/8" x 1-3/4" Clevis Pin (Q)

and a large Hairpin Cotter (U).

REAR

SUPPORT

CHANNEL

FRONT

PLATE

3/8" X 1"

CARRIAGE BOLT (H)

3/8" NYLOCK

NUT (K)

4" to 5"

GROUND

1/2"X 1" CLEVIS PIN (R)

LARGE HAIRPIN COTTER (U)

1/2" WASHER (P)

FIGURE 11 - SEARS TRACTOR SHOWN

STEP 11:

(SEE FIGURE 11)

•

Slide the Thrust Channel under the front of the tractor.

Attach the Hanger Brackets to the Frame Brackets

using two 1/2" x 1" clevis pins (R), 1/2" washers (P)

and large hairpin cotters (U).

STEP 9:

(SEE FIGURE 9)

•

Install the Rear Locating Bracket to the top of the

Rear Mounting Bracket using two 3/8" x 1" Carriage

bolts (H) and 3/8" nylock nuts (K).

Tighten

nuts.

•

Install the Rear Support Channels to the middle set of

holes in the sides of the Rear Mounting Bracket using

four 3/8" x 1" Carriage Bolts (H) and 3/8" nylock nuts

(K).

Finger tighten only.

FIGURE 12 - SEARS TRACTOR SHOWN

3/8" X 1"

CARRIAGE BOLT (H)

3/8" NYLOCK

NUT (K)

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 358.796355 Bedienungsanleitung

Craftsman

Craftsman ZT 7000 Bedienungsanleitung

Craftsman

Craftsman 19A30041791 Bedienungsanleitung

Craftsman

Craftsman 19B30005791 Bedienungsanleitung

Craftsman

Craftsman 486.242411 Bedienungsanleitung

Craftsman

Craftsman 2 IN ONE MULCHER/BAGGER 917.37248 Bedienungsanleitung

Craftsman

Craftsman 486.24449 Bedienungsanleitung

Craftsman

Craftsman 917.248950 Bedienungsanleitung

Craftsman

Craftsman 358.795792 Bedienungsanleitung

Craftsman

Craftsman 358.792410 Bedienungsanleitung

Craftsman

Craftsman 757.242330 Bedienungsanleitung

Craftsman

Craftsman 610.24610 Bedienungsanleitung

Craftsman

Craftsman 358.795631 Bedienungsanleitung

Craftsman

Craftsman 29918 - 17 in. Dual Rear Tine Tiller-CA... Bedienungsanleitung

Craftsman

Craftsman 358.795781 Bedienungsanleitung

Craftsman

Craftsman 25322 Bedienungsanleitung

Craftsman

Craftsman 486.24326 Bedienungsanleitung

Craftsman

Craftsman 917.249040 Bedienungsanleitung

Craftsman

Craftsman 247.24019 Bedienungsanleitung

Craftsman

Craftsman 610.240842 Betriebsanleitung

Craftsman

Craftsman 3One 917.257562 Bedienungsanleitung

Craftsman

Craftsman 917.252492 Bedienungsanleitung

Craftsman

Craftsman 917.248930 Bedienungsanleitung

Craftsman

Craftsman 358.792410 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung