Craftsman 486.24847 Bedienungsanleitung

Owner's Manual

I:RI:IFT. MRN®

Model No. 486.24847

FRONT SCOOP TRACTOR ATTACHMENT

CAUTION:

Before using this product, read this

manual and follow all Safety Rules

and Operating Instructions.

IMPORTANT - READ THIS FIRST???

For Missing Parts or Assembly Questions

Please Call 866-576-8388

Mon.-Fri. 7 a.m.-5 p.m. CST.

FAX 217-728-2032 or e-mail [email protected]

Missing parts will be sent UPS in 24 hours directly to your home.

• Safety

• Assembly

• Operation

• Maintenance

• Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsma n

PRINTED IN U.S.A. FORM NO. 49326 (1/05)

WARRANTY .............................................................. 2

SAFETY RULES ........................................................ 3

FULL SIZE HARDWARE CHART ............................. 4

CARTON CONTENTS .............................................. 6

ASSEMBLY ............................................................... 7

OPERATION ............................................................ 14

MAINTENANCE ...................................................... 15

TROUBLESHOOTING ............................................ 15

REPAIR PARTS ILLUSTRATION .......................... 16

REPAIR PARTS LIST ............................................. 17

SLOPE GUIDE ........................................................ 19

PARTS ORDERING/SERVICE ................. Back Page

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN FRONT SCOOP TRACTOR ATTACHMENT

For one year from the date of purchase, when this scoop is maintained and lubricated according to the operating and

maintenance instructions in this owner's manual, Sears will repair any defect in material or workmanship free of

charge. If this scoop is used for commercial or rental purposes, this warranty applies for only 90 days from the date of

purchase.

This warranty does not cover repairs necessary because of operator negligence or abuse, including the failure to

maintain the equipment according to instructions contained in this owner's manual.

WARRANTY SERVtCE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER/

DEPARTMENT IN THE UNITED STATES.

This warranty applies only while this product is in the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D/817 WA., Hoffman Estates, Chicago, IL 60179

The model number and serial number will be found on a

decal attached to the bucket.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

486.24847

Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment.

Exercisecautionatalltimes,whenusingpowerequipment.

• Readthis owner'smanualbeforeattemptingto

assembleoroperatethescoopattachment.

• Readthevehicleowner'smanualandknowhowto

operate your vehicle before using the scoop

attachment.

• Nevercarrypassengersinthescoopbucket.Ithas

notbeendesignedtocarrypassengers.

• Neverallowchildrento operatethevehicleor the

scoopattachment.

• Donotallowadultstooperatethevehicleorscoop

attachmentwithoutproperinstructions.

• Alwaysbeginwiththetransmissioninfirst(low)and

graduallyincreasespeedasconditionspermit.

• Drivethetractoratreducedspeedoverroughterrain

andhillsidesornearcreeksandditchesto prevent

tippingoverandlossofcontrol.Donotdrivetooclose

toacreekorditch.

• Neverramthescoopintomaterialathighspeed.

• Vehiclebrakingandstabilitymaybeaffectedwiththe

attachmentof thisscoop.Donotfill thescoopto

maximumweightcapacitywithout checkingthe

capabilityofthevehicletosafelydriveandstopwith

thescoopattached.

• Beforeoperatingvehicleonanygrade(hill)referto

the safety rules in the vehicle owner'smanual

concerningsafeoperationon slopes.Referalsoto

theslopeguideonpage19ofthismanual.Stayoff

steep slopes!

• Follow maintenance and lubrication instructions as

outlined in this manual.

Look for this symbol to point out important safety precautions. It means--Attention!!

Become alert!! Your safety is involved.

These accessories were available when the unit was purchased. They are also available at most Sears retail outlets and

service centers. Most Sears stores can order repair parts for you when you provide the model numbers of your tractor and

scoop.

WHEEL WEIGHT

DiF

/FF

PARTS NOT SHOWN FULL SIZE

PARTS BAG CONTENTS

Not all parts will be needed for fit-up to any one tractor.

Discard uneeded parts after assembly is finished.

REF. QTY.

A 2

B 2

C 3

D 2

E 4

F 5

G 5

H 3

t 2

J 2

K 1

L 2

M 2

N 3

O 2

P 2

Q 12

R 5

S 1

T 1

DESCRIPTION REF.

Hex Bolt, 5/8" x 1-1/2" U

Hex Bolt, 1/2" x 1-1/2" V

Hex Bolt, 1/2" x 1" W

Hex Bolt, 3/8" x 1-1/4" X

Hex Bolt, 3/8" x 1" Y

Hex Bolt, 5/16" x 1" Z

Hex Bolt, 5/16" x 1-3/4" AA

Hex Bolt, 1/4" x 1-3/4" BB

Carriage Bolt, 5/16-18 x 1" CC

Carriage Bolt, 1/4-20 x 3/4" DD

Slotted Truss Head Bolt, 10-32 x 5/8" EE

QTY. DESCRIPTION

6Lock Washer, 3/8"

3 Washer, 1/4"

8 Washer, 5/16"

3 Washer, 1/2" Small

6 Washer, 5/8"

2 Washer, 1/2" Large

2 Washer, 3/4"

2 Washer, 1"

3 Hairpin Cotter, Long

4 Hairpin Cotter, Short

6 Cotter Pin, 1/8" x 1-1/4"

Nylock Nut, 5/8" FFF

Nylock Nut, 1/2" GG

Nylock Jam Nut, 1/2" HH

Hex Nut, 3/8" tt

Nylock Nut, 3/8" JJ

Nylock Nut, 5/16" KK

Nylock Nut, 1/4" LL

Hex Nut, 1/4" MM

Nylock Nut, #10-32

2 Cotter Pin, 1/8" x 1-1/2"

4 Spacer, 1/2"

1 Spacer, 3/8" Small

2 Clevis Pin

1 Compression Spring

6 Cable Tie

2 Tilt Stop Bracket

1 Hose Clip

CARTON CONTENTS

1. Bucket Assembly

2. Pin Stop Bracket

3. Lift Frame Assembly

4. Lift Bracket Assembly

5. Tilt Anchor Assembly

6. Right (LT) Side Plate

7. Left (LT) Side Plate

8. Right (GT) Side Plate

9. Left (GT) Side Plate

10. Dump Control Rod

11. Lift Strap Assembly (2)

12. Tilt Bracket Assembly

13. Attachment Rod

14. Dump Handle Tube

15. Lift Handle Tube

16. Dump Handle Tube Extension

17. Dump Pivot Bracket

18. Lift Handle Tube Extension

19. Dump Control Pin

20. Lift Cable (Short)

21. Lift Cable (Long)

6 8

11 -

j12 %

TOOLS REQUIRED FOR ASSEMBLY

(1)

(2)

(1)

#2 Phillips Screwdriver

Standard Screwdriver

15/16" Wrenches (one should be box-end)

3/4" Wrenches

9/16" Wrenches

7/16" Wrenches

1/2" Wrenches

3/8" Wrench

ADDITIONAL ITEMS NEEDED

Ruler or Tape Measure

Grease

STEP 1 - REMOVE PARTS FROM CARTON

• Remove the hardware pack and all loose parts from

the carton.

• Lay cardboard on floor to help prevent scratching of

painted parts.

• Lay out and identify all the parts and hardware as

shown on pages 4 through 6.

5/16" WASHERS

______------5/16" x 1"

HEX BOLT

L PIN STOP

./BRACKET

i BUCKET

ASSEMBLY

5/16"

NYLOCK NUT

3/8" NYLOCK NUT

FIGURE 1

3/8" x 1o1/4"

HEX BOLT

3/8" HEX NUT

STEP 2 - INSTALL TWO BOLTS

• Assemble two 3/8" x 1-1/4" hex bolts and 3/8" hex

nuts, threading the nut all the way onto the bolt until it

is tight against the head of the bolt. See figure 1.

• Install a nut/bolt assembly into the bucket assembly

and fasten using a 3/8" nylock nut. Tighten. Repeat

for the other side. See figure 1.

STEP 3 - INSTALL PIN STOP BRACKET

Install the pin stop bracket to the top of the bucket

assembly using four 5/16" x 1" hex bolts, eight 5/16"

washers and four 5/16" nylock nuts. Center the bolts

in the slots of the pin stop bracket and the slots of the

bucket. Tighten the bracket so that it is square with

the bucket. See figure 1.

STEP 4 - INSTALL LIFT FRAME ASSEMBLY

• Apply grease to the mounting surface of the bucket

assembly and the inside of the lift frame arms.

See figure 2.

Assemble the lift frame assembly to the bucket

assembly using two 5/8 x 1-1/2" hex bolts and 5/8"

nylock nuts. Tighten, then loosen the nuts 1/4 turn,

or until the lift frame pivots freely. See figure 2.

5/8" x 1-1/2"

HEX BOLT

APPLY

GREASE j _-

APPLY LIFT FRAME

GREASE ASSEMBLY

5/8" NYLOCK NUTS

FIGURE 2

APPLY GREASE

STEP 5-INSTALL LIFT BRACKET ASSEMBLY

• Assemble the lift bracket assembly to the lift frame

assembly using two 5/8" washers and 1/8" x 1-1/4"

cotter pins. See figure 3.

LIFT FRAME

ASSEMBLY

FIGURE 3

STEP 6 - INSTALL TILT ANCHOR ASSEMBLY

• Assemble the tilt anchor assembly to the lift bracket

assembly using two 1/2" x 1" hex bolts and nylock

jam nuts. Tighten. See figure 4.

1/2" NYLOCK

JAM NUTS

TILT ANCHOR

ASSEMBLY

1/2" x 1"

HEX BOLT

LIFT

BRACKET

1/2" x 1"

HEX BOLT

STEP 7 - INSTALL LIFT STRAP ASSEMBLIES

• Loosen the bolts and nuts on the lift strap

assemblies 1/4 turn or until the straps will slide back

and forth. You will retighten them later in step 24.

Turn the lift strap assemblies as shown. Install each

lift strap assembly to an arm of the lift bracket

assembly and then secure with a small 1/2" washer

and a short hairpin cotter. See figure 5.

Position the lower end of each lift strap assembly to

the outside of the lift frame. Fasten to the upper front

holes in the lift frame using a 1/2" x 1" clevis pin, 1/2"

spacer and short hairpin cotter for each assembly.

See figure 5.

NOTE: The lift strap assemblies may be installed in the

rear mounting holes of the lift frame to increase

the lift height, but this will also increase the lifting

effort. The front holes give a lift height of about 6-

1/2" and require 28 Ibs. of force to lift a 150 Ib

load. The rear holes will give a lift height of about

8-1/2" and require 35 Ibs. of force.

SHORT HAIRPIN

COTTER

/1/2" WASHER

_.@../ (SMALL)

LIFT STRAP

SHORT ASSEMBLY

HAIRPIN /_\%

COTTER

1/2"SPACER

UPPER FRONT 1/2"x 1"

MOUNTING HOLE CLEVIS PIN

FIGURE 5Bucket removed for clarity.

FIGURE 4

STEP 8 - INSTALL TILT BRACKET ASSEMBLY

NOTE: If you mounted the lift strap assemblies in Step 7

to the rear holes in the lift frame for increased

lifting height, you need to replace the 3/8" spacer

on the tilt bracket assembly with the smaller 3/8"

spacer from the parts bag at this time.

Loosen the bolts and nuts on the tilt bracket

assembly 1/4 turn or until the two plates will slide

back and forth. You will retighten them later in step

23. See figure 6.

Lightly apply grease to the end of the arm on the tilt

anchor assembly and install the tilt bracket assembly

to the arm using a 1/2" x 1" hex bolt and 1/2" nylock

jam nut. Tighten. Loosen the nut 1/4 turn, or until the

tilt bracket assembly pivots freely. See figure 6.

Install a 1/4" x 1-3/4" hex bolt through a 1/4" washer

and then through the end of the extension spring on

the tilt bracket assembly. Next, install a 1/4" hex nut

all the way onto the threads of the bolt. Finally install

the end of the bolt into the hole in the arm of the tilt

anchor assembly and secure using a 1/4" nylock nut.

Tighten. See figure 6.

STEP 9 - INSTALL DUMP PIVOT BRACKET

Install a 1/8" x 1-1/2" cotter pin to the inside hole in

the shaft shown in figure 9, and then install a 1"

washer onto the shaft. Apply grease to the end of the

shaft and install the dump pivot bracket assembly

onto the shaft. Install a 1" washer onto the shaft and

secure it using a 1/8" x 1-1/2" cotter pin. See figure 7.

1/8" x 1-1/2"

COTTER PIN

_'_ 1"WASHERS

APPLY

GREASE

1/8" x 1-1/2"

COTTER PIN

DUMP PIVOT

BRACKET

FIGURE 7

1/4" NYLOCK NUT

TILT ANCHOR

ASSEMBLY_

1/4" HEX NUT

1/2" x 1"

HEX BOLT

1/4" WASHER

IAPPLY

1/4"x 1-3/4" GREASE

HEX BOLT 1/2" NYLOCK

JAM NUT TILT BRACKET

ASSEMBLY

FIGURE 6

STEP 10 - INSTALL DUMP CONTROL ROD

Install a 1/8" x 1-1/4" cotter pin into the inside hole in

each end of the dump control rod. Spread the ends of

the cotter pins and wrap around the rod. Install a 5/8"

washer onto each end of the control rod. See figure 8.

Install the dump control rod to the dump pivot bracket

and bucket. Fasten using two 5/8" washers and 1/8" x

1-1/4" cotter pins. Spread the ends of the cotter pins

and wrap around the rod. See figure 8.

1/8" x 1-1/4"

COTTER PIN

5/8" WASHERS

1-1/4"

COTTER

PINS

1/8" x 1-1/4"

COTTER PIN 5/8" WASHERS

DUMP

CONTROL

ROD

FIGURE 8

STEP 11 - INSTALL TILT STOP BRACKETS

Install a tilt stop bracket to each side of the bucket

using a 1/4" x 3/4" carriage bolt, 1/4" washer and 1/4"

nylock nut. Do not tighten the nuts until step 25. See

figure 9.

STEP 13 - INSTALL LIFT HANDLE TUBE

EXTENSION

• Install the lift handle tube extension on the lift handle

tube using a 1/4" x 1-3/4" hex bolt and 1/4" nylock

nut. See figure 11.

TmLT STOP

8RACKET

1/4" NYLOCK _.

NUT 1/4" x 3/4"J

1/4" WASHER CARRIAGE BOLT

FIGURE 9

FIGURE 11

LIFT HANDLE

TUBE EXTENSION

l,;'x;'O3'LZ'"

1/4" NYLOCK NUT

LIFT HANDLE

TUBE

STEP 12 - INSTALL LIFT HANDLE TUBE

• Install the lift handle tube on the index bracket using

two 5/16" x 1-3/4" hex bolts and 5/16" nylock nuts.

See figure 10.

LIFT HANDLE

TUBE

5/16"

NYLOCK 5/16" x 1-3/4"

-_®_ HEX BOLT

INDEX

FIGURE 10

STEP 14 -INSTALL LIFT CABLE

Squeeze the lift trigger and slide the anchor end of the

lift (short) cable into the hole in the trigger. Release

the trigger and guide the cable through the slot in the

bottom of the trigger and trigger housing. Insert the

end of the plastic cable covering into the trigger

housing. See figure 12.

Connect the hooked end of the lift cable into the index

rod, and install the threaded cable adjuster into the

notch in the top of the index bracket, placing a nut on

each side of the notch. See figure 12.

Adjust the cable adjuster nuts so that when the trigger

is squeezed, the bottom of the index rod raises

enough to release from the latched position. The index

rod should also lower far enough to lock in the latched

position when the trigger is released. See figure 12.

• Attach the lift cable to the lift handle using three cable

ties.

Inhaltsverzeichnis

Andere Craftsman Rasen- und Gartengeräte Handbücher

Craftsman

Craftsman 486.244412 Bedienungsanleitung

Craftsman

Craftsman 486.248463 Bedienungsanleitung

Craftsman

Craftsman 917.252492 Bedienungsanleitung

Craftsman

Craftsman 2 IN ONE MULCHER/BAGGER 917.37248 Bedienungsanleitung

Craftsman

Craftsman 316.792570 Bedienungsanleitung

Craftsman

Craftsman CMXGZBF71242131 Bedienungsanleitung

Craftsman

Craftsman 0944.511590 Bedienungsanleitung

Craftsman

Craftsman 917.248930 Bedienungsanleitung

Craftsman

Craftsman 358.792410 Bedienungsanleitung

Craftsman

Craftsman 917.248951 Bedienungsanleitung

Craftsman

Craftsman 358.795630 Bedienungsanleitung

Craftsman

Craftsman CMCW211 Bedienungsanleitung

Craftsman

Craftsman 45-04381 Bedienungsanleitung

Craftsman

Craftsman 29281 Bedienungsanleitung

Craftsman

Craftsman 358.795792 Bedienungsanleitung

Craftsman

Craftsman CompuCarve 183.217540 Bedienungsanleitung

Craftsman

Craftsman CMXMLBA5618A Bedienungsanleitung

Craftsman

Craftsman 486.244120 Bedienungsanleitung

Craftsman

Craftsman 486.24449 Bedienungsanleitung

Craftsman

Craftsman Incredi-Pull 316.794450 Bedienungsanleitung

Craftsman

Craftsman ELECTRIC WEEDWACKER C944.512200 Bedienungsanleitung

Craftsman

Craftsman 486.24414 Bedienungsanleitung

Craftsman

Craftsman POWER RAKE 486.2928 Bedienungsanleitung

Craftsman

Craftsman 247.24035 Bedienungsanleitung

Beliebte Rasen- und Gartengeräte Handbücher anderer Marken

Vertex

Vertex 1/3 HP Technische Daten

GHE

GHE AeroFlo 80 Bedienungsanleitung

Millcreek

Millcreek 406 Bedienungsanleitung

Land Pride

Land Pride Post Hole Diggers HD25 Bedienungsanleitung

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch

Premier designs

Premier designs WindGarden 26829 Bedienungsanleitung

Snapper

Snapper 1691351 Bedienungsanleitung

Mosquito Magnet

Mosquito Magnet Patriot Bedienungsanleitung

Perfect

Perfect BG2 Bedienungsanleitung

P.Lindberg

P.Lindberg LS2 Bedienungsanleitung

Gardena

Gardena Easy 1887 Bedienungsanleitung

Makita

Makita UM104D Bedienungsanleitung

AQUA FLOW

AQUA FLOW PNRAD Bedienungsanleitung

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Benutzerhandbuch

BIOGROD

BIOGROD 730710 Bedienungsanleitung

Land Pride

Land Pride RCF2784 Bedienungsanleitung

Makita

Makita UM110D Bedienungsanleitung

BOERBOEL

BOERBOEL Standard Floating Bar Gravity Latch Bedienungsanleitung