Craftsman 351.183200 Bedienungsanleitung

[SAVE THIS MANUAL

FOR

FUTURE REFERENCE

OWNER'S

MANUAL

MODEL NO.

351.183200

CAUTION:

READ ALL

INSTRUCTIONS

CAREFU LLY!

__/_/_)_/1:: RI:1FTSM I:!N

Framing Nailer

•safety instructions

• operating instructions

• replacement parts

Sold by SEARS, ROEBUCK AND CO., 3333 Beverly Road. Hoffman Estates, IL 60179 _)

Part No. 6186.00 July 1994

DESCRIPTION

The Sears Framing Nailer drives nails of 0 113 to 0..131"

diameter from 2 to 3 1/2" tong. Magazine is angled at

27 1/2° for nailing in tight spots such as when toenail-

ing. High strength, aluminum components are

lightweight and durable. Contact safety disables nailer

until nosepiece isin contact with workptece Hardened,

serrated contact tip grips wood for fast, easy nailing

Large capacity, top load magazine makes it easy to

load up 105 stick nails at a time. Nailer drives straight,

screw, and ring shank nails. The Sears Angle Framing

Nailer is exce!lent for truss making, framing, sheating,

sub-flooring and decking.,

. SPECIFICATIONS

Capacity ............................... 75 to 105 nails

Nail Size .......................... 0113 to 0.131"

Nail Lengths ............................. 2 to 3 I/2"

Operating Pressure ..................... 75 to 100 PSIG

Air inlet ........................ 1/4" FNRT

Length ............... ...................... :183/8"

Height ........................................ 13 3/4"

Width ...................................... 5 1/8"

Weight ................................ 8,3 lbs

NAILS

£18351 ...... 8 penny, .120" diameter x 2 1/2" long

918352 ......... 10 penny,. 120" diameter x 3" long

£18353 ..... 16 penny, .131"diameter x 3 1/2"long

SAFETY INSTRUCTIONS

Air tool operators and all others in work area should

always wear safety goggles (must comply with ANSl

Z87.1) to prevent eye injury from fasteners and flying

debris when loading, operating or unloading this tool

Never exceed operating pressure of 100 PSlG (7 1

kg/cm 3),,

Always keep hands and body away from the fastener

discharge area when air supply is connected to tool,.

Always disconnect tool from air supply when servicing

or adjusting toot and when tool is not in use.

Do not operate toot when nose is not in contact with

work,

/_ FILTEr,-_GLIAT_2- L_21[A'fl]_

FENLEDUll[-I]IS[N,_'E[T--J

Figure I-

Do not operate tool if contact trip mechanism is not

functioning properly

Never load the tool until you are ready to use it.

Never depress tool trigger when loading.

Always load tool with nose pointing away from you and

others.

Never point the tool at yourself or others

Never carry too! with trigger depressed

Do not use oxygen, combustible gases or high pres-

sure compressed gas as the air supply for the tool,

Always use tool at safe distance from other people in

work area.

Do not attempt to discharge fastener into hard or brittle

materials such as concrete, steel or tile.

._-Do not connect female quick-disconnect coupling to

tool side of air line

Connect male free-flow nipple to tool side of air line so

that tool is depressurized when disconnected from

hose.

Do not use a hose swivel in air supply line,

Use Sears recommended fasteners only.

OPERATING INSTRUCTIONS

AIR SUPPLY LINE

Refer to Figure 1.

The Sears Framing Nailer operates on compressed air

at pressures from 75 to 100 PSIG.

Never exceed maximum pressure.

The minimum air requirements for nailer: Average

working SCFM, 40 at go PSI with a 3/8" air hose and

15 gallon tank

WARNING: KEEP HANDS AND BODY AWAY FROM

DISCHARGE AREA OF NAILER WHEN

CONNECTING AIR SUPPLY. ALWAYS

DISCONNECT TOOL FROM AIR SUP-

PLY WHEN SERVICING, ADJUSTING

AND WHEN TOOL IS NOT IN USE.

Clean dry air is essential to operation of Sears nailer.

Air operated tools require clean, dry, lubricated com-

pressed atr to ensure top performance, tow

maintenance and long life

Dirt and abrasive materials present in all air lines wilt

damage tool O-rings, valves and cylinders.

/_2 FDD]_E _HIP

--2--

OPERATING INSTRUCTIONS (Continued)

AIR SUPPLY LINE (Continued)

Moisture will reduce tool performance and life if not

removed from compressed air,

A filter-regulatorolubricator system is required and

shouid be located as close to tool as possible (see

Figure 1). A distance of less than t5 feet is recom-

mended1

Keep air filter clean. A dirty filter will reduce air pressure

to nailer causing a reduction in power and efficiency

The air supply system must be able to provide air

pressure of 75 to 100 pounds per square inch at the

toot.

The lubricator should be filled with a non-detergent air

tool oil.,

All hoses and pipes in the air supply system must be

ctean and free of all moisture and foreign particles,,

Never connect a female quick-disconnect coupling to

too! side of air system A male free-flow coupling should

be connected to the tool side of air system,

The female coupling provides a seal, preventing loss of

compressed air from compressor tank when discon-

nected from male coupling. If connected to tool side of

air supply, the femaTe coupling could seal a com-

pressed a!r charge in the nailer which could discharge

if the tool trigger is actuated,

The air pressure should be Properly regulated.

Different workpiece materials and different nail lengths

will require different operating pressure.

Use oniy as much air pressure as required, Using more

air pressure than needed will waste compressed air

and cause unnecessary wear to nailer.

Be sure all connections in air supply system are sealed

tOprevent air Ioss,

Refer to Figures 2 and 5.

NOTE: For best results use Sears nails only

WARNING: DISCONNECT TOOL FROM AIR SUP-

PLY. ALWAYS LOAD WITH NOSE OF

TOOL POINTING AWAY FROM YOU

AND OTHERS. ALWAYS WEAR SAFETY

GOGGLES THAT COMPLY WITH ANSI

Z87.1o

Slide pusher handle (Ref, No, 59) towards rear of tool

until it locks into position,

Insert nails into opening at top of magazine.

Hold pusher handle firmly and release by depressing

latch (Ref. No, 55). Allow pusher to gently slide forward

against nails°

_.NAILING OPERATION

WARNING: NEVER OPERATE TOOL UNLESS CON.

TACT TRIP IS IN CONTACT WITH

WORKpIECEo DO NOT OPERATE TOOL

WITHOUT NAILS OR DAMAGE TO

TOOL MAY'RESULT. NEVER FIRE

NAILS INTO THE AIR BECAUSE NAILS

MAY INJURE OPERATOR OR OTHERS

AND DAMAGE TO TOOL MAY RESULT.

The Sears Framing Nailer is equipped with a contact

trip safety mechanism that disables nailer unless con-

tact trip is pushed against work. Hotd tooi handle firmly

and place nose of tool on location where nail is to be

applied. Pull trigger to drive nail into workpiece.

Figure 2 -Loading. Fram!nq Nails Figure 3 - Contact Trio Operation

-3-

OPERATING INSTRUCTIONS (Continued)

OPERATING PRESSURE

Use only enough air pressure to perform the nailing

operation Air pressure in excess of that which is re-

quired will make the nailing operation inefficient and

may cause premature wear or damage to the tool,

Determine minimum air pressure required by driving

some test nails Into the workpiece, Set air pressure so

that test nai! heads are driven down flush with the work

surface, Nails driven too deep may damage workpiece

MAINTENANCE

Inspect contact trip safety mechanism daily for proper

operation.

WARNING: DO NOT OPERATE NAILER IF SAFETY

MECHANISM IS NOT OPERATING

PROPERLY.

Perform the following procedures to test safety

mechanism:

1. Leave trigger untouched while pushing contact

trip into workpiece. Nailer must not fire_

2 Pull nailer trigger while contact trip isclear of work

and pointed away from operator and others Nailer

must not fire.

3 Depress and hold trigger Push contact against

work where nail is needed, The nailer should drive

only one nail each time the contact trip is pushed

against workpiece,

ff contact trip does not operate properly, repair imme-

diately through Sears Service Center.

Replace any damaged or missing parts, Use the parts

list to order parts..

Lubricate tool each day the tool is used with quality air

tool oil. If no air line lubricator is used, pour five to six

drops of oil into inlet (Key No 22, Figure 5) of nailer,

Keep the magazine and nose of the natler clean and

free of any dirt, lint or abrasive particles.

The tip of the ram (Key No 11, Figure 5) can become

dented or rounded over time, Square off the tip of the

ram with a clean, fine hand file to extend the life of the

ram and naiter_ Nail firing will be more consistent ifthe

ram tip is kept clean and square

TROUBLESHOOTING

WARNING: DISCONNECT TOOL FROM AIR SUP-

PLY BEFORE ATTEMPTING REPAIR OR

ADJUSTMENT.

.....Note: Be sure tool is oiled properly. Clean and oil all

O-rings during reassembly

If too_ losers power or operates inconsistently, put five

or six drops of air tool oil into inlet cap (Key No 22).

If tool continues to operate improperly, the piston and

cylinder valve O-rings should be lubricated with

silicone grease Remove cap, cylinder valve and piston

(Key Nos. 4, 9 and 11).

Check O-rings and replace if worn, stretched or

damaged. Clean all O-rings and O-ring grooves with

clean, dry cloth.. Coat all O-rings and O-ring grooves

with air nailer grease or silicone grease Be careful not

to pinch or damage O-rings during assembly As-

semble in reverse order of disassembly

If tool fires but nail is not discharged from magazine,

check piston O-ring (Key No, 10) Also, check all O-

rings in trigger valve assembly (Key Nos 35 - 45),

If tool leaks air out of nose, check cylinder O-ring (Key

No. 13) and spacer O-ring (Key No. 17)

Iftoot leaks air out of e×ha ust port, check cylinder valve

O-rings (Key Nos 7 and 8),

FULL ONE YEAR WARRANTY ON SEARS/CRAFTSMAN FRAMING NAILER

If within one full year from the date of purchase, this Sears Craftsman Framing Nailer fails due to a defect

in material or workmanship, Sears will repair it, free of charge.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING THE NAILER TO THE NEAREST SEARS

STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES.

This warranty gives you specific legal rights, and you may have other fights which vary from state to state.

Sears, Roebuck and Coo, Dept, 817 WA, Hoffman Estates, IL 60179

--4-

NOTES

ii___,_i_,

011 C

I.,,_ It

2-.._

_Sm5

L,/,j

REPLACEMENT PARTS LIST FOR FRAMING NAILER

KEY" PART

NO. NO.

I I77500

2 1514.00

36301 B0

4 6302,00

5 6303.00

6 6304.00

7 6305.00

8 6306.00

9 6307,00

10 630800

11 6309,,00

12 631000

13 63t 1,,00

14 631200

15 6313.00

16 6314,00

17 6315,00

18 6316_00

19 6317o00

20 631 &00

6320.00

23 0814L00

24 46-58494-3

25 6321.00

26 6322.00

27 6323,00

28 6324,00

29 632500

30 0483,00

3t 0824.00

32 632600

33 6327.00

34 6328.00

35 6148,00

36 6149o00

37 6150,00

38 6151.00

39 6152,00

40 6153,00

41 6154.00

42 6155,00

DESCRIPTION QTY,

64,0 x 25mm Bolt,

socket head* 4

6mm Washer, split* 4

Rubber plug 1

Cap t

Cap seal 1

Cylinder valve spring 1

Cylinder valve O-ring,

inside

Cylinder valve O-ring,

outside

Cylinder valve

Piston O-ring

Ram-piston assembly

Cylinder cap

Cylinder O-ring, top

Cylinder

Cylinder O-ring, bottom

Bumper

Cylinder spacer O-ring

Cylinder spacer

Cap gasket

Nailer body

Inlet cap gasket

Inlet cap

5-08 x 20ram Bolt,

socket head*

5mm Washer, split

Nose O-ring*

Nose bumper

Ram guide

3 x 8mm Pin, roll

Nose

8-1,25 x 30mm Bolt,

socket head 4

8mm Washer, split 4

Contact trip spring 1

Contact trip 1

Plastic shroud 1

Breather valve O-ring, top 1

Breather valve 1

Breather valve O-ring,

outside 1

O-ring 1

Valve 1

O-ring 1

Spring 1

*Standard hardware item available locally

eNot shown.

KEY

NO.

PART

NO.

615600

6157 00

615800

615900

6329 00

6161 00

6162 00

6164 00

6163 00

6330 00

633100

6332 00

633300

6334.00

6088 00

619600

633500

6336 00

6337 00

6338 00

6339,00

6340 00

6341.00

634200

6343,00

6344.00

6345,00

634600

635400

6347,00

73 634800

74 634900

75 6350,00

76 6O8690

77 619800

78 1218 00

79 6351.00

80 6352,00

81 6353,00

•6! 86,00

,. ,,,

DESCRIPTION

Plunger

O-ring

Seal

Cap

Bracket

Trigger

Lever

Spring pin

Spring

Latch bracket

Latch spring

Latch bushing

Latch

Latch shaft

4-0 7 x 10ram Bolt,

socket head

4mm Washer, split

Pusher

5 x 20mm Spring pin

5 x 12mm Spring pin

Plastic block

3-05 xl 4ram Boit,

socket head

3mm-0 5 Nut, fiber hex

Spring shaft

Spring spindle

Magazine spring

Spindle cover

Magazine

6-1 0 x 12ram Bolt,

socket head*

6-I.0 Nut, fiber hex

5-08 x 25mm Bolt,

socket head*

5mm Washer, flat*

6ram-0 8 Nut, fiber hex

Magazine bracket

4-0 7 x 8mm Bolt,

socket head

4ram-0 7 Nut, fiber hex

8-I 25 x 16ram Bolt,

socket head*

6ram Washer, flat

8ram Bushing

Nail wear plate

Owner's Manual

RECOMMENDED ACCESSORIES

QTY.

8 penny, .120 dia. x 2 1/2" long

10 penny, .120 dia. x3" long

16 penny, .131 dia x3 1/2"long

918351

918352

918353 J

-7-

OWNER'S

MANUAL

SERVICE

MODEL NO.

351.183200

HOW TO ORDER

REPLACEMENT

PARTS

Framing Nailer

Thank you for purchasing Your Framing Nailer from Sears,

This unit will provide you with many years of reliable service

Should the, need exist for repair parts or service, simply

contact any Sears Service Center and most Sears, Roebuck

and Co stores Be s_re to provide air pertinent facts when

you call or visit The modei number of your Framing Nailer is

on the front of the nailer

All parts listed may be ordered from any Sears Service

Center and most Sears stores If the parts you need are not

stocked locally, your order wi{I be electronically transmitted

to the Sears Repair Parts Distribution Center for handling

When ordering replacement parts, always give the following

information:

NAME OF ITEM: Framing Nailer

MODEL NUMBER: 351,183200

PART NUMBER:

PART DESCRIPTION:

Sold by SEARS, ROEBUCK AND CO., 3333 Beverly Road. Hoffman Estates, IL 60179 @

Part No. 6186.00 June 1994

Inhaltsverzeichnis

Andere Craftsman Nagelpistole Handbücher

Craftsman

Craftsman 351.184240 Bedienungsanleitung

Craftsman

Craftsman CMP21PL Bedienungsanleitung

Craftsman

Craftsman C583-930360 Bedienungsanleitung

Craftsman

Craftsman 351.184090 Bedienungsanleitung

Craftsman

Craftsman CMCN618 Bedienungsanleitung

Craftsman

Craftsman 351.181810 Bedienungsanleitung

Craftsman

Craftsman 351.184440 Bedienungsanleitung

Craftsman

Craftsman CMCN621PL Bedienungsanleitung

Craftsman

Craftsman 351.182930 Bedienungsanleitung

Craftsman

Craftsman Easy Fire 0993056 Bedienungsanleitung

Craftsman

Craftsman 351.183220 Bedienungsanleitung

Craftsman

Craftsman CMPBN18 Bedienungsanleitung

Craftsman

Craftsman 351.184360 Bedienungsanleitung

Craftsman

Craftsman 900.684253 Bedienungsanleitung

Craftsman

Craftsman 142.18803 Bedienungsanleitung

Craftsman

Craftsman 351.181790 Bedienungsanleitung

Craftsman

Craftsman CMCN616 Bedienungsanleitung

Craftsman

Craftsman 18178 - Full Head Framing Nailer Bedienungsanleitung

Craftsman

Craftsman 351.184420 Bedienungsanleitung

Craftsman

Craftsman 351.184540 Bedienungsanleitung

Craftsman

Craftsman 351.184300 Bedienungsanleitung

Craftsman

Craftsman 351.181750 Bedienungsanleitung

Craftsman

Craftsman 315.115120 Bedienungsanleitung

Craftsman

Craftsman 351.183210 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung