Craftsman 351.183220 Bedienungsanleitung

SAVE THiS MANUAL

FOR

FUTURE REFERENCE

OWNER'S

MANUAL

MODEL NO.

351.183220

CAUTION:

READ ALL

INSTRUCTIONS

CAREFULLY!

FIN®

An le Finishin ailer

®safety instructions

•operating instructions

®replacement parts

Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A. ©

Part No. 75_3.01 SEPTEMBER 1993

DESCRIPTION

The Sears Angle Finishing Nailer drives 15 gauge nails

from 1 1/2 to 2 1/4" long and 14 gauge nails 2 1/2" long

Magazine is angled for nailing in tight spots.. Tapered

nose makes precise nail placement easy. Die cast

aluminum body is light weight and balanced to reduce

operator fatigue_ Contact safety disables nailer uritil

nosepiece is in contact with workpiece. Convenient

rear load magazine makes loading nails easy. The

Sears Angle Finishing Nailer-is ideal for interior and

exterior molding, furniture making and cabinetry°

SPECIFICATIONS

Capacity ...................... I00 nails, 15 gauge

.................................... 90 nails, 14 gauge

Finish nail lengths ..................... 1 1/2 to 2 1/2"

Operating pressure ....................... 60-100 PSIG

Air inlet .................................. 1/4" N..RTE

Length ..................................................... 13"

Height ........................................ 11 1/2"

Width .......................................... 3 3/4"

Weight .......................................... 53/4 tbs.

FINISH NAILS

918348 ................ 15 gauge finish nails, 1 t/2" long

9.18349 .................. 15 gauge finish nails, 2" long

918350 .............. 14 gauge finish nails, 2 1/2" long

SAFETY INSTRUCTIONS

Air tool operators and all others in work area should

always wear safety goggles (must comply with ANSI

Z87.t) to prevent eye injury from fasteners and flying

debris when loading, operating or unloading this tool

Never exceed operating pressure of 100 PSIG (7.1

kg/cm3).

Always keep hands and body away from the fastener

discharge area when air' supply is connected to tool

Always disconnect tool from air supply when servicing

or adjusting tool and when tool is not in use,,

Do not operate tool when contact trip is not in contact

with work

Never load the tool untUyou are ready to use it,,

Never depress tool trigger when Ioading_

Always load tool with tool pointing away from you arid

others.

Never' point tool at yourself or others.

Never carry tool with trigger depressed.

Do not use oxygen, combustible gases or high pres-

sure compressed gas as the air' supply for the toot,

Always use tool at safe distance from other people in

work area,,

Do not attempt to discharge fastener into hard or brittle

materials such as concrete, steel or tile.

Do not connect female quick-disconnect coupling to

tool side of air'line_

Connect male free-flow nipple to tool side of air line so

that tool is depressurized when disconnected from

hose°

Use Sears recommended fasteners only,

OPERATING INSTRUCTIONS

AIR SUPPLY LINE

Refer to Figure I.

The Sears air nailer operates on compressed air at

pressures from 60 to 100 PSIG.

Never exceed maximum pressure.

Minimum air requirements for nailer: Average working

SCFM 40 at 90 PSI with a 3/8" air hose and 15 gallon

tank..

WARNING: KEEP HANDS AND BODY AWAY FROM

DISCHARGE AREA OF NAILER WHEN

CONNECTING AIR SUPPLY.

ALWAYS DISCONNECT TOOL FROM

AIR SUPPLY WHEN SERVICING OR AD-

JUSTING TOOL AND WHEN TOOL IS

NOT IN USE,

_j_ FILTE_-P,EELLAI_-LL(BP,I_IOR

FEHkLEDUI_-OISCI)N)IE[T

Figure 1- HALEOUICK-OISCOhrrECT

--2--

OPERATING INSTRUCTIONS (Continued)

AIR SUPPLY LINE (Continued)

Clean dry air is essential to the operation of the Sears

nailer, Air operated tools require clean, dry, lubricated

compressed air to ensure top performance, tow main-

tenance and long life.

Dirt and abrasive materials present in all air lines will

damage tool O-rings, valves and cylinders,

Moisture wilt reduce tool performance and life if not

removed from compressed air,.

A _ter-regulator-lubricator system is required and

should be located as close to tool as possible (see

Figure 1), a distance of less than 15 feet is recom-

mended.

Keep air filter clean. A dirty filter will reduce the air

pressure tothe nailer causing a reduction in power and

efficiency.

The air supply system must be able to provide air

pressure of 60 to 100 pounds per square inch at tool..

The lubricator should be filled with a nomdetergent air

tool oil.

All hoses and pipes in the air supply system must be

clean and free of all moisture and foreign particles,.

Never connect a female quick-disconnect coupling

to the tool side of air system. A male, free-flow cou -

piing should be connected to the tool side of air

system° The female coupling provides a sea! prevent-

ing loss of compressed air frorn compressor tankwhen

disconnected from male coupling.. If connected to tool

side of air supply, the female coupling could seal a

compressed air charge in the naiter which could dis-

charge ifthe tool trigger is actuated,

The air pressure should be properly regulated_ Do not

mount swivel connector in air suppiy line.

Different workpiece materials and different nail lengths

will require different operating pressure..

Be sure all connections in air supply system are sealed

to prevent air Iosso

Refer to Figures 2 and 5,.

WARNING; DISCONNECT TOOL FROM AIR SUP-

PLY.ALWAYS LOAD NAILER WITH NOSE OF TOOL

POINTING AWAY FROM YOU AND OTHERS. AL_

WAYS WEAR SAFETY GOGGLES THAT COMPLY

WITH ANSI Z87°1.

1. Insert nails into rear of magazine with heads of

nails in top of slot (see Figure 2a below)..

Figure 2a - Loadinq

2_ Slide nails to front of magazine past nail stop

bracket (Key No_ 40, Figure 5).. See Figure 2b

below.

Figure 2b - LoadinCl

3. Slide pusher (Key Noo31, Figure 5) over nails and

nail stop bracket to rear of magazine_ Slide pusher

forward against nails_See Figure 2c below.

Figure 2c - Loadinq .....

UNLOADING

Refer to Figures 3 and 5.

Place finger inside round hole in pusher cover and

press pusher (Key No. 31, Figure 5) to release nails_

Slid e pusher to front of magazine, Slide nails out of rear

of magazine_

Press pusher here

to release nails

Figure 3 - Unloadinq

-3-

OPERATING INSTRUCTIONS (Continued)

NAILING OPERATION

Refer to Figure 4.

WARNING: NEVER OPERATE TOOL UNLESS CON-

TACT TRIP IS IN CONTACT WITH WORKPIECE. DO

NOT OPERATE TOOL WITHOUT NAILS OR DAM-

AGE TO TOOL MAY RESULT. NEVER FIRE NAILS

INTO THE AIR BECAUSE NAILS MAY INJURE OP-

ERATOR OR OTHERS AND DAMAGE TO TOOL MAY

RESULT.

The Sears 15 Gauge Finishing Nailer is equipped with

acontact trip safety mechanism that disables nailer

unless contact trip is pushed against work. Hold tool

handle firmly and press nose of tool on workpiece

where nail is to be applied. Pull trigger to drive nail into

workpiece.

The nailer can also be operated by holding trigger

depressed and pushing contact trip against work°

piece. This operating procedure is preferred for

rapid-fire nail driving. Never operate tool unless con-

tact trip is in contact with workpiece.

OPERATING PRESSURE

Use only enough air pressure to perform the operation.

Air pressure in excess of that which is required will

make the nailing operation inefficient and may cause

premature wear or damage to the tool

Different workpiece materials and different nail lengths

witt require different qperating pressure. Determine

minimum air pressure required by drk,ing some test

nails into the workpiece° Set air pressure so that test

nail heads are driven down flush with the work surface.

Nails driven too deep may damage workpiece.

Air pressure can be adjusted for nail countersinking.

MAINTENANCE

Lubricate too! daily with quality air tool oil If no air' line

lubricator is used, place five to six drops of oil into inlet

of nailer' everyday,

Keep magazine and nose clean and free of anydirt, tint

or abrasive particles.

The tip of the ram (Key No. t !) can become dented or

rounded over time. Square off tip of the ram with a

clean, fine hand file to extend the life of the ram and

nailer° Nail firing will be more consistent if the ram tip is

kept clean and square,

Figure 4 - Contact Trip Operation

inspect contact trip safety mechanism daily for proper

operation. Do not operate nailer if mechanism is not

operating propedy

Perform the following procedures to test safety mecho

anism:

1. Leave trigger untouched while pushing contact

trip into workpiece. Nailer must not fire°

2. Pull nailer trigger while contact tr!p is clear of work

and pointed away from operator and others,.

Nailer must not fire,

3. Depress and hold trigger. Push contact trip

against workpiece where nail is needed. The nailer'

should drive only one nail each time the contact

trip is pushed against workpiece.

REPAIR NAILER IMMEDIATELY IF CONTACT

TRIP MECHANISM DOES NOT OPERATE

PROPERLY.

Repair or replace any missing or' damaged parts Use

the parts list to order parts_

FULL ONE YEAR WARRANTY ON CRAFTSMAN AIR-DRIVE TOOLS

if this Craftsman air.drive tool fails to give complete satisfaction within one year from

the date of purchase, RETURN IT TO THE NEAR_:ST SEARS SERWCE CENTER/

DEPARTMENT IN THE UNITED STATES, and Sears will repair it, free of charge.

if this Air-Drive Tool is used for commercial purposes, this warranty applies for

only 90 days from the date of purchase.

This warranty gives you specific legal rights and you may also have other rights which

vary from state to state.

Sears, Roebuck and Co., Dept. D/817 WA, Hoffman Estates, IL 60195

k_4_

TROUBLESHOOTING

WARNING: DISCONNECT TOOL FROM AIR SUP-

PLY BEFORE ATTEMPTING REPAIR OR

ADJUSTMENT.

...... , ,,,,,,,............ , ,, ........

SYMPTOM POSSIBLE CAUSE.,(S)

Trigger cap leaks 'ai'r t° O-ring damaged

Trigger leaks 1, O-ring damaged

air

Cap leaks

air

NOse leaks

air

not operate

Tool'operates

slowly or

loses power

Tool skips staple!

inconsistent operation

Refer to Figure 5,,

Note: Be sure tool is oiled propedy_ Clean and oil all

O-rings during reassembly,

CORRECTIVE ACTION

1, Check and replace damaged O-ring

.............. (Key NO. 64)

1o Check and replace damaged' O'fin'gs

................................ (Key No s. 55, 58, 60, 6!, 62,t & 64)

,1. 1, Tighten bolts (Key No. 1)

2_ Damaged cap gasket ........ 21, Check and replace damaged gasket

(Key No_9 8)

...."{"_'#,lose"bolts loose 1. Tighten bo_ts (Key No. 68),,

2, Check and replace damaged gasket

(Key NO.65)

3," Damaged bumper ........3, Check and replace damaged bumper

..........(Key No.,,15) ,

'11' lns,uff_cientair supply 1. Check air supp!y .....

2,, Insufficient lubrication 2, Place five or six drops of air tool oit into inlet

cap (Key ,No,23),,,,

....3'i"'Damager"or worn cylinder Valve O-rings 3, Replace damaged or worn O:tings ......

, (Key ace. 6 & 7)

41 Broken _lind'er va'ive spring 4. Replace broken spring (Key No. 5) "

5, CyIinder valve binding in cap 5, Clean and lubricate valve and cap

(Key' Nos. 8 & 3) ................

''ii lnsufficientlubrication ............... 1,. Place five of six drops of air tool

oil into inlet cap (Key NO, 23)

2. Broken cylinder valve spring ............. ., .12: check and replace brok,en,,,,spring(Key No. 5)

3, Damaged or worn O-rings 3r Check and replace damaged or

worn O-rings .................

4, Damaged trigger assembly ........ i 4, Check and replace trigger assembly

5, Build-up on ram 5, "Clean and lubricate ram/piston

assemb!,y (Key No. 11)

6. Cyl!,nder not sealed on bumper properly ......... 6, D!sassemble cylinder and assemble properly

7, Cylinder vaive poorly lubricated 7, Disassemble cylinder vaive (Key No. 8). clear_

................................................. and lubricate, assemble properly .....

.8, Insufficient _r,,Supply ............................ 8:,, Check air supply,

I, Worn or damaged bumper 1, Check and repface bumper

(Key NO. I5)

Bulld_up on ram or nose _ '2. Clean and lubricate ram/piton assembly

(Key No 11) and inside of nose and nose

cover (Key Nos. 74 & 76)

insufficient air'supply ............ ,'ii 3. Check a_rsupply "

4. Damaged or worn P!Ston O-ri,ng ......... 4. Check and replace O-(ing (Key No. 10)

5. Insufficient lubrication 5, Place five or six drops of air tool oil

into inlet cap (Key N,o,.,23)

6, Darnaged"mag_i[n e Spii_ ..... ......... Check, ,and replace spring, (Key No, 35)

7. Magazinetnose bolt loose ......... ,7. Tighten bo!t (Key No, 43)...........

8. Nails too short 8, Use Sears recommended nails only

9, Damaged nails 9 Discard damaged naiEs. Use Sears

,,, recommended nails only

10. Incorrect nail size 10.,, USe sears recommended nails only

11. Cap gasket leaks 1!, Tighten cap bolts (Key No, 1),

Check and repface damaged cap

,gasket (Key No, 18) .......

12, Damaged triggei'vaive O-ring 12, check and replace damaged O-rings

(Key Nos, 55, 58, 60, 61, 62 & 64)

i3_ Bent or damaged ram..... 13:,Check and replace damaged ram/piston

assem,bly (Key No. !1)

14. Dirty magazine .................. 14. Clean magazine and lubricat ewith air toot o,!,!

15 Damaged or worn magazine 15, Check and replace magazine (Key No, 30)

-5-

MODEL 351.183220

C)"

Figure 5 -,Replacement Parts Illustration

-6-

REPLACEMENT PARTS LIST FOR NAILER

PART KEY

NO. DESCRIPTION QTY.' NO,

t775 00 6-1 0 x 25mm Bolt, socket head 4 43

58-100020 6mm Washer, lock 10 44

8362 00 Cap 1 45

7467 00 Cap seat I 46

7468.00 Cylinder valve spring t 47

6 .... 7469 00 ]o:ring, cyi'i"ndervalve, inside ! 48

7 7470.00 O.ring, cylinder valve, outside 2 49

8 7471 00 Cylinder valve t 50

9 747200 Valve seat 1 5!

...........!.0 6I t 1.00 O-ring, pisto n ..... 1.... 52

t 1 7530. oo Ram/Piston assembly 1 53

12 6t t2 00 O-ring, cylinder 1 54

13 7473.01 Cylinder 1 55

I4 7474 00 Baffle 1 56

15 7531.00 Bumper 1 57

16 747600 O.ring, cylinder spacer 1 58

t7 7477 00 Cylinder spacer 1 59

18 7478.00 Cap gasket 1 60

19 748200 5-0 8 x 18ram Bolt, socket head t 6t

20 58-100014 5ram Washer, fiat* I 62

21 7479 00 Nai._erbody t 1 63

22 6121.00 Inlet cap gasket 1 64

23 7480.00 Inlet cap 1 65

24 0814 00 5-0 8 x 16ram Bolt, socket head 5 66

25 46-58494-3 5ram Washer, lock* 4 67

26 753200 Magazine bracket I 68

27 6349.00 5-08 Nut, fiber hex 1 69

28 6080.00 4-0 7 Nut, fiber hex 5 70

29 7533 00 3 x 34ram Pin, spring ! 71

30 7534.00 Magazine 1 72

31 7535 00 Pusher 1 73

32 7487 00 Roller t 74

33 7536 00 Magazine cap 1 75

34 7537 00 4-0 7 x 10mm Screw, sckt pan hd t 76

35 7488 00 Magazine spring 1 77

36 7538.00 Pusher cover 1 78

37 7539 00 3 5 x 28mm Pin, dowel 2 79

38 7540 O0 Wear plate 1 e

39 754t.00 4-0.7 x 8ram Screw, socket pan hd. 2

40 754200 Nail stop bracket t e

41 753700 4_07 x 10mm Screw, sock. pan hd, 1 •

42 6270.00 5_0.8 x 8mm Bolt, socket head 1 e

PART

NO.

6078 00

46.58470_3

6349 00

46-58436-3

6086.00

46-22561-3

6t63 O0

616100

616200

6160.00

6159,00

6158 00

6t57.00

6156 00

6155 00

6t36 00

6! 53.00

6151.00

615100

6150.00

6t4900

6050.00

7498°00

7544.00

7545.00

0179 00

7546 00

46-5690-3

7547 00

7548.00

7549 00

7550.00

7551 O0

7552.00

8051.00

6045.00

8361.00

7553.01

DESCRIPTION QTY.

............. i .........

4-0.7 X 12ram Bolt, socket head 1

4ram Washer, lock* 1

5-0 8 Nut, fiber hex 1

4mm Washer, flat* 1

4-0.7 x 8mm Bolt, socket head 1

3 x 25mm Pin, spring* 3

3 x 16mm Pin, spring 1

Trigger 1

Lever 1

Safety bracket 1

Trigger cap 1

O-ring, trigger cap 1

O-ring, plunger 2

Plunger 1

Plunger spring 1

O-ring, trigger valve, bottom 1

Trigger valve 1

O-ring, trigger valve, middle 1

O-ring, trigger valve, top 1

O-ring, breather valve, bottom 1

Breather valve 1

O-ring, breather valve, top 1

Nose gasket 1

Ram guide 1

Nose plate 1

6-10 x 20mm Bolt, socket head 6

Contact trip arm 1

4-0.7 Nut, hex* 1

Contact trip 1

Rubber cushion 1

Contact trip spring 1

',lose 1

',lose bracket 1

Nose cover 1

Pusher spring 1

5-0.8 x 20ram Bolt, socket head 3

Cylinder bracket 1

Owner's Manual 1

RECOMMENDED ACCESSORIES

9 I8348

9- 18349

_918350

15 Gauge Finish Nails, 1 1/2" long 1

15 Gauge Finish Nails, 2" long 1

t4 Gauge Finish Nails, 2 I/2" long 1

eNot shown

*Standard hardware item available locally.

-7-

OWNER'S

MANUAL

SERVICE

MODEL NO.

351,183220

HOW TO ORDER

REPLACEMENT

PARTS

Angle

nishing aiier

Thank you for purchasing your Angle Finishing Nailer from

Sears, This unit will provide you with many years of reliable

service° Should the need exist for repair parts or' service,

simply contact any Sears Service Center and most Sears,

Roebuck and Co, stores. Be sure to provide all pertinent

facts when you call or' visit. The model number of your

Angle Finishing Nailer is on the front of the nailer.

All parts listed may be ordered from any Sears Service

Center and most Sears stores° If the parts you need are not

stocked locally, your order will be electronically transmitted

to the Sears Repair Parts Distribution Center for handling.

when ordering replacement parts, always give the following

information:

NAME OF ITEM: Angle Finishing Nailer

MODEL NUMBER: 351,1 83220

PART NUMBER:

PART DESCRIPTION:

Part No. 7553.01 SEPTEMBER 1993

Inhaltsverzeichnis

Andere Craftsman Nagelpistole Handbücher

Craftsman

Craftsman CMCN616 Bedienungsanleitung

Craftsman

Craftsman CMCN618 Bedienungsanleitung

Craftsman

Craftsman 351.184300 Bedienungsanleitung

Craftsman

Craftsman 900.684253 Bedienungsanleitung

Craftsman

Craftsman CMCN621PL Bedienungsanleitung

Craftsman

Craftsman 2723303 836.27233 Bedienungsanleitung

Craftsman

Craftsman CMCN616 Bedienungsanleitung

Craftsman

Craftsman 142.18894 Bedienungsanleitung

Craftsman

Craftsman 351.153000 Bedienungsanleitung

Craftsman

Craftsman 351.181740 Bedienungsanleitung

Craftsman

Craftsman ETT3012H Bedienungsanleitung

Craftsman

Craftsman CMP21PL Bedienungsanleitung

Craftsman

Craftsman CMCN623 Bedienungsanleitung

Craftsman

Craftsman 315.115122 Bedienungsanleitung

Craftsman

Craftsman 315.115120 Bedienungsanleitung

Craftsman

Craftsman 351.182930 Bedienungsanleitung

Craftsman

Craftsman 351.184360 Bedienungsanleitung

Craftsman

Craftsman CMPBN18 Bedienungsanleitung

Craftsman

Craftsman 351.181720 Bedienungsanleitung

Craftsman

Craftsman 351.182010 Bedienungsanleitung

Craftsman

Craftsman CMPPN23 Bedienungsanleitung

Craftsman

Craftsman 351.183230 Bedienungsanleitung

Craftsman

Craftsman 142.18803 Bedienungsanleitung

Craftsman

Craftsman 351.181770 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

DAJ

DAJ XR150A Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung