Craftsman 351.182930 Bedienungsanleitung

Operator's Manual

ERRFTSHRNo

PALM NAILER

Model No.

351.182930

CAUTION: Read and follow

all Safety Rules and Operating

Instructions before First Use

of this Product.

• Safety

•Operation

•Parts List

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

2698.01 Draft (06/21/00)

Warranty ...................... 2Troubleshooting ................ 5

Safety Rules................... 2 Parts Illustration and List ........ 6-7

Operation ................... 2-3

FULL ONE YEAR WARRANTY ON CRAFTSMAN AIR-DRIVE TOOLS

If this Craftsman air-drive tool fails due to adef_=ctin material or workmanship

withinone full year from the date of purchase, return it to the nearest Sears

Service Center in the United States, and Sears will repair it free of charge.

If this air-drive tool is used for commercial purposes, this warranty applies for

only 90 days from the date of purchase.

This warranty gives you specific legal rights and you may also have other

rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

• Air tool operators and all othersin

work area should always wear safety

gogglescomplyingwith United

States ANSI Z87.1 to preventeye

injuryfromfasteners and flying

debris when loading, operating or

unloadingthis tool,

• Never exceed operating pressure of

100 PSI.

• Always keep hands end body away

from the fastener discharge area

when air supply is connected to tool.

• Always disconnect tool from air sup-

ply when servicing or adjusting tool

and when tool is not in use.

• Never pointtoolat yourselfor others.

•Do net use oxygen,combustiblegas

or high pressure compressed gas as

the air supplyforthe tool.

• Alwaysuse toolat safe distance

fromother people in work area.

Do not attempt to dischargefastener

intohard or brittle materials suchas

concrete, steel or tile.

•Do not connect female quick-discon-

nect coupling to tool side of air line.

• Connect male, frae-fiow nipple to

tool side of air line so that tool is

depressurized when hose is discon-

nected.

Do not usea hose swivelwiththis

tool,

DESCRIPTION

The Craftsman Palm Nailer drives 2-5"

long nails. Lightweight die cast alu-

minum body with handle provides easy

maneuverability in where hammers and

other tools will not work. Nailer has a

magnetic noseto hold nails for accu-

rate, safe placement and includes abelt

hook. Craftsman nailer is ideal for

installation of electrical boxes, rafter

bracing, joint hangers, fencing, decking

and framing.

SPECIFICATIONS

Nail length ........... 2_5" (5d-40d)

Nail head size (dia.)........ V,to ,3/=,,

Nail size (dia.) ............ %, to 3/_,,

Operating pressure ...... 60-100 PSI

Air inlet................. V," N.RT.

Length....................... 8"

Height...................... 51/2,'

Width ...................... 33/,"

Weight.................. 1.50 Ibs.

AIR SUPPLY LINE

Referto Figure 1.

•The air tooloperates on compressed

air at pressures from 60 to 100 PSI.

•Never exceed maximum pressure.

Minimum air requirements for tool:

Averageworking SCFM 2.6 at 90 PSI.

WARNING: Keep handsand body

away from dischargearea oftoolwhen

connectingair supply.Alwaysdiscon-

necttool from air supplywhen servicing

or adjustingtooland whentool is not in

use.

•Airoperatedtools require clean, dry,

compressedairto ensuretopperfor-

mance, lowmaintenance and longlife.

•Dirt and abrasivematerials present

in all air lines will damage tool

O-rings,valves and cylinders.

•Moisture will reduce tool perfor-

mance and lifeif not removed from

compressed air.

•A filter-regulatorsystem is required

and should be located as closeto

tool as possible (see Figure 1). A

distance of lessthan 15 feet is re(:-

ommended.

•Keep air filter clean. A dirty filter will

reduce the air pressureto the tool

causing a reductionin powerand

efficiency.

•The air supplysystem must be able

to provideair pressureof 60 to 100

pounds per square inch at tool.

•All hoses and pipes in the air supply

system must be clean and free of

moistureand foreign particles.

•Do not mountswivel connectorin air

supplyline.

•The air pressura shouldbe properly

regulated.

•Differentworkpieco materials and

fastener lengthswillrequire different

operatingpressure.

•Be sure all connectionsin air supply

systemare sealedto preventairloss.

Never connecta female quick*dis-

connectcouplingto the tool side of

air line connection.A male,free-flow

coupling shouldbe connected tothe

tool side of air lineconnection.

WARNING: The female couplingpro-

vides a seal preventingloss of com-

pressedair from compressortank when

disconnectedfrom male coupling. If

connected to toolside of air supply,the

female couplingcould seal a com-

pressedair charge in the tool which

coulddischarge if the trigger is

actuated.

2Foot HoseWhip

Male Quick-Disconnect

Filter- Regulator

Female Quick-Disconnect

Figure 1 -Air Supply Line

NAILING OPERATION

Refer to Figures2 & 3, pages 4 and 6.

WARNING: Do notoperate toolwith-

outfasteners or damage totool may

result.Never pointthe toolat yourself or

others.

• Positionand place the fastener

where it must be applied.

•Slide the nailer on to the fastener so

thatthe magnets in the guide bush-

ing (Key No. 18) contactthe fastener

head.

•Hold bodyfirmly withpalm on the

palm rest and fingers on the finger

rest. If necessary, use other hand on

the handle.

•Gently push nailer against fastener

head to activate.The nailer will auto-

matically stop when the nail is driven

completely.

Palm Rest Finger Rest

OPERATING PRESSURE

• Use only enough air pressure to per-

form the operation.Air pressurein

excess ofthat which isrequired will

make the operation inefficientand

may cause prematurewear or dam-

age to the tool.

•Determine minimumair pressure

required by drivingsome test fasten-

ers intothe workpiece.Set air pres-

sure so that test fasteners are driven

down flush withthe work surface.

Fastenersdriven too deep may dam-

age workpiece.

_uide

Handle lJ

Flgure 2 - Nailing Operation

SYMPTOM

3ap leeksair

Fool leaks air

Foolwill not

3perate

Fooloperates

_lowly or loses

:)ower

POSSIBLE CAUSE(S)

1, Cap bolts loose

2, Damaged gasket

1. Damaged O-rings

2. Damaged Bumper

1. Insufficientair supply

2. Damaged or worn

head valve O-rings

3. Head valve binding

1. Damaged or worn

O-rings

2, Cylinder notsealed

on bumper properly

3, Insufficientair supply

CORRECTIVE ACTION

1. Tighten bolts (Fig.3, No. 1)

2. Check and replace damaged

gasket (Fig. 3, Nos. 4 and 5)

1. Check and replece damaged

O-rings (Fig. 3, Nos.6, 11 and 13

2. Check and replace damaged

bumper (Fig. 3, No. 14)

1. Check air supply

2. Replace damaged or worn

O-rings (Fig. 3, No. 6)

3. Clean and lubricate cap and

valve (Fig. 3, Nos. 3 and 8)

1. Check and replace damaged

or worn O-rings

2. Disassemble cylinder and

assemble properly

3. Check air supply

Model351.182930

Figure 3 -Replacement Parts Illustration for Stapler

PART NO. DESCRIPTION

1 6045.00 5-0.8 x2Omm Socket Head Bolt

2STD852005 5mm Lock Washer*

3 9810.00 Cap

4 9811.00 Gasket

5 9812.00 Seal

6 9813.00 52.07 x 2.62mm O-Ring

7 9814.00 Ring

8 9815.00 Valve

9 9816.00 Seal

10 9817.00 Cylinder Assembly

11 9818,00 42.20 x 3.5ram O-Ring

12 9819.00 Piston Ram Assembly

13 9820.00 59.50 x 2mm O-Ring

14 9821.00 Bumper

15 9822.00 Bushing

16 9823.00 Body

17 9824.00 Spring

18 9825.00 Guide Bushing with Magnets

19 9827.00 Seal

20 9828.00 Guide Box

21 9959.00 Hanger

22 5331.00 5-0.8 x 12ram Socket Head Bolt

2698.01 Operator's Manual

*Standard hardware item available locally.

ANot Shown

In U.S.A, or Canada

for in-home major brand repair service:

Call 24 hours aday, 7 days a week

1-800-4-MY-HOME _ (1-800-469-4663)

Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811

Au Canada pour tout le service - 1-877-LE-FOYER" (1-877-533-6937)

For the repair or replacement parts you need:

Call 6a.m. - tl p.m. CST, 7 days a week

PartsDirect

1-800-366-PART (1-800-366-7278)

www.sears.com/pa rtsdirect

Para ordenar piezas con entrega a domicnio - 1-800-659-7084

For the location of a Sears Service Center in your area:

Call 24 hours a day, 7 days a week

1-800-488-1222

To purchase or inquire about a Sears Maintenance Agreement:

Call 7 a.m. - 5 p.m. CST, Monday - Saturday

1-800-827-6655

Andere Craftsman Nagelpistole Handbücher

Craftsman

Craftsman 351.184540 Bedienungsanleitung

Craftsman

Craftsman 351.184360 Bedienungsanleitung

Craftsman

Craftsman 351.182920 Bedienungsanleitung

Craftsman

Craftsman 351.181790 Bedienungsanleitung

Craftsman

Craftsman 351.184200 Bedienungsanleitung

Craftsman

Craftsman 351.184240 Bedienungsanleitung

Craftsman

Craftsman 351.184440 Bedienungsanleitung

Craftsman

Craftsman CMCN616 Bedienungsanleitung

Craftsman

Craftsman 351.181740 Bedienungsanleitung

Craftsman

Craftsman CMCN618 Bedienungsanleitung

Craftsman

Craftsman 351.183200 Bedienungsanleitung

Craftsman

Craftsman CMPBN18 Bedienungsanleitung

Craftsman

Craftsman CMCN621PL Bedienungsanleitung

Craftsman

Craftsman C583-930360 Bedienungsanleitung

Craftsman

Craftsman 18178 - Full Head Framing Nailer Bedienungsanleitung

Craftsman

Craftsman CMP21PL Bedienungsanleitung

Craftsman

Craftsman ETT3012H Bedienungsanleitung

Craftsman

Craftsman CMPFN16 Bedienungsanleitung

Craftsman

Craftsman 351.181810 Bedienungsanleitung

Craftsman

Craftsman 351.153000 Bedienungsanleitung

Craftsman

Craftsman 2723303 836.27233 Bedienungsanleitung

Craftsman

Craftsman 142.18839 Bedienungsanleitung

Craftsman

Craftsman 142.18803 Bedienungsanleitung

Craftsman

Craftsman 351.181720 Bedienungsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung

Black & Decker

Black & Decker 90514937 Bedienungsanleitung