Craftsman 315.212100 Bedienungsanleitung

Owner's Manual

IERRFTSMRN'I

ACCESSORIES FOR MODEL NOS. 315.212100 AND 315.212110

10 in. (254 mm) COMPOUND MITER SAW

Item No.

_924310

_924350

Save this manual for

future reference.

_, CAUTION: Read and follow

all Safety Rules and Operating

Instructions before first use of

this product.

• SAFETY

•LOOSE PARTS

•INSTALLATION

•SERVICES

Customer Help Line: t-800-932-3188

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

Visit the Craftsman web page: www.sears.com/craftsman

972000-603

2-00

READ ALL INSTRUCTIONS

•READ THESE INSTRUCTIONS AND THE IN-

STRUCTIONS FOR THE 315.212100 COM-

POUND MITER SAW THOROUGHLY before

using accessories.

•KNOW YOUR POWER TOOL. Read the owner's

manual for the Compound Miter Saw carefully.

Learn the saw's applications and timitations as well

as the specific potential hazards related to this

tool,

•KEEP THE WORK AREA CLEAN, Cluttered work

areas and work benches invite accidents. DO NOT

leave tools or pieces of wood on the saw while it is

in operation.

•ALWAYS WEAR SAFETY GLASSES. Everyday

eyeglasses have only impact-resistant lenses; they

are NOT safety glasses.

•ALWAYS DISCONNECT SAW FROM POWER

SUPPLY BEFORE MAKING ADJUSTMENTS OR

ADDING ACCESSORIES. Make sure the switch is

offwhen reconnecting to power supply.

•SAVE THESE INSTRUCTIONS. Refer tothem

frequently and use to instructother users. If you

loan someone thistool, loan them these instruc-

tionsalso.

_k Look for this symbol to point out important safety precautions. It

means attention!!! Your safety is involved.

The following accessories are includedwith item no. 924310 and &2.4350:

• Work Clamp

• Dust Bag

• Table Extensions (2)

• Stop Block

• Small Wing Screw

• Clamp Bracket (2)

• Clamp Bracket Screws (2)

• Owner's Manual

WORKCLAMP

SMALL WINGBCREW

EXTENSIONS

S_CREW

STOPBLOCK

CLAMP BRACKET

Fig. 1

_1, WARNING: The use of attachments or accessories not listed might be hazardous.

_l, WARNING: To prevent accidental starting that

could cause possible serious personal injury,

assemble all parts to your saw completely before

connecting it to power supply. Saw should never

be connected to power supply when you are

assembling parts, making adjustments, installing

or removing blades or accessories, or when not

in use.

WORK CLAMP

See Figure 2.

The worl_ clamp provides greater control by clamping

the workpiece to the fence. It also prevents the

workpiece from creeping toward the saw blade. This

is very I?elpful when cutting compound miters. To

install the work clamp, place the shaft of the clamp in

either hole in front of the miter table base. Rotate the

knob on the clamp to move it in or out as needed.

_, WARNING: Make sure the saw blade or blade

guard will not hit the work clamp assembly when

cutting 35 ° to 45° angles. Failure to heed this

warning can result in serious personal injury.

WORK

CLAMP

MITER TABLE BASE Fig. 2

DUST BAG

See Figure 3.

The dust bag fits over the exhaust port on the upper

blade guard. To install it, remove the dust guide from

the exhaust port. Then, squeeze the two metal clips to

open the mouth of the bag and slide it on the exhaust

port. Release the clips. The metal ring in the bag

should lock in between the grooves on the exhaust

port. For more efficient operation, empty dust bag

when no more than half full. This will permit better air

flow through the bag.

DUST BAG

EXHAUST PORT

Fig. 3

TABLE EXTENSIONS

See Figure 4.

To install table extensions, insert the ends of the

extensions into the holes in the sides of the base.

Secure them in place by positioning a clamp bracket

under each table extension beneath the miter table.

Orient each clamp bracket as shown in figure 4.

Secure each clamp bracket in place with a clamp

bracket screw. The clamp bracket screw threads

through the clamp bracket and tightens against

bottom of miter table, securing clamp bracket against

table extension.

SAWVIEWED

FROMBELOW

CLAMP

BRACKET

TABLEEXTENSION

Fig. 4

STOP BLOCK

See Figures 5 and 6.

The stop block is useful as a stop for cutting multiple

pieces to the same length. It can be installed on either

table extension on either side of the saw base:

• Slide the stop block on the back arm of either table

extension, then insert the table extension into the

saw base. See Figure 5.

• Use the small wing screw to secure the stop block

to the table extension. See Figure 5.

•Loosen the small wing screw and adjust the stop

block the desired distance from the blade for the

cut to be made.

STOPBLOCK

SMALL

WINGSCREW

MITERSAWBASE

EXTENSION Fig. 5

• Tighten small wing screw securely,

• Make a test cut in scrap material and measure the

length of the workpiece.

• Make any necessary adjustments.

_, WARNING: When using the work clamp with

the stop block, installthe clamp o_ the stop block

side of the blade. This will eliminate the

possibility of the saw catching the loose end and

kicking up. Failure to heed this warning can

result in serious personal injury.

STOP

BLOCK

Fig. 6

Andere Handbücher für 315.212100

Dieses Handbuch passt für folgende Modelle

Andere Craftsman Gesehen Handbücher

Craftsman

Craftsman 320.21228 Bedienungsanleitung

Craftsman

Craftsman 103.22181 Gebrauchs- und Pflegehandbuch

Craftsman

Craftsman SIERRA CIRCULAR 315.CT2040 Bedienungsanleitung

Craftsman

Craftsman 9-29012 Bedienungsanleitung

Craftsman

Craftsman 113.234880 Bedienungsanleitung

Craftsman

Craftsman 351.221160 Bedienungsanleitung

Craftsman

Craftsman 137.212410 Bedienungsanleitung

Craftsman

Craftsman 315.243130 Bedienungsanleitung

Craftsman

Craftsman CMES500 Bedienungsanleitung

Craftsman

Craftsman 315.17280 Bedienungsanleitung

Craftsman

Craftsman 315.212400 Bedienungsanleitung

Craftsman

Craftsman 137.224120 Bedienungsanleitung

Craftsman

Craftsman 118.22320 Bedienungsanleitung

Craftsman

Craftsman Contactor 113.236400 Bedienungsanleitung

Craftsman

Craftsman 315.21234 Bedienungsanleitung

Craftsman

Craftsman 137.218020 Bedienungsanleitung

Craftsman

Craftsman 315.271290 Bedienungsanleitung

Craftsman

Craftsman 172.26043 Bedienungsanleitung

Craftsman

Craftsman 113.23611t Bedienungsanleitung

Craftsman

Craftsman 113.290060 Bedienungsanleitung

Craftsman

Craftsman 22299 Bedienungsanleitung

Craftsman

Craftsman 315.218060 Bedienungsanleitung

Craftsman

Craftsman 320.17291 Bedienungsanleitung

Craftsman

Craftsman 137.407530 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung