Craftsman Professional 320.27224 Bedienungsanleitung

Operator's Manual

Scrolling

PART#

Reciprocatin

2341123003

Model No. 320. 27224

CAUTION! Read, understand and

follow all Safety Rules and Operating

Instructions in this Manual before

using this product.

oWarranty

oSafety

• Unpacking

, Description

•Assembly

= Maintenance

Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A.

www.craftsman.com

Warranty Page 2

Safety Symbols Page 3

Safety Instructions Pages 4-9

Unpacking Pages 9-10

Description Pages 10-1 t

Operation Pages 12-14

Maintenance Page 15

Troubleshooting Page t 5

Parts List Pages 16-t 7

Sears Repair Parts Phone Numbers Pages 18

ONE YEAR FULL WARRANT'/' ON CRAFTSMAN ®PROFESSIONAL

TOOL

If this Craftsman Professional tool fails to give complete satisfaction

within one year from the date of purchase, return it to any Sears store

or other Craftsman Professional outlet in the United States for free

replacement.

This warranty does not cover expendable parts, such as blades and

lamps.

This warranty gives you specific legal rights, and you may also have

other rights, which vary from state to state°

Sears, Roebuck and Co., Hoffman Estates 1L60179

WARNING: Some dust created by using power tools contains chemicals

known to the state of California to cause cancer and birth defects or other

reproductive harm.

SAVE THESE INSTRUCTIONS!

READ ALL INSTRUCTIONS!

27224 Manual_Revised_09-0608 PaSe 2

The purpose of safety symbols is to attract your attention to possible dangers.

The safety symbols and the explanations with them deserve your careful

attention and understanding. The symbol warnings do not, by themselves,

eliminate any danger. The instructions and warnings they give are no substitutes

for proper accident prevention measures.

,_ WARNING: Be sure to read and understand all safety instructions in this

manual, including all safety alert symbols, such as "DANGER," "WARNING,"

and "CAUTION," before using this Reciprocating Saw. Failure to following all

instructions listed below may result in electric shock, fire and/or serious personal

injury,

SYMBOL MEANNING

,_ SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION.

May be used in conjunction with other symbols or pictographs_

_k DANGER; Failure to obey this safety warning will result in death or serious

injury to yourself or to others. Always follow the safety precautions to reduce the

risk of fire, electric shock, and personal injury.

,_ WARNING: Failure to obey this safety warning can result in death or serious

injury to yourself or to others. Always follow the safety precautions to reduce the

risk of fire, electric shock, and personal injury.

,_k CAUTION: Failure to obey this safety warning may result in death

or serious injury to yourself or to others. Always follow the safety precautions to

reduce the risk of fire, electric, shock and personal injury.

DAMAGE PREVENTION AND INFORMATION MESSAGES

These inform user of important information and/or instructions that could lead to

equipment or other property damage if not followed. Each message is preceded

by the word "NOTE" as in the example below.

NOTE: Equipment and/or property damage may result if these instructions

are not followed.

WEAR YOUR

27224 Manual Revised 09-0608

The operation of any power tool can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool

operation, always wear safety goggles or safety glasses

with side shields and a full-face shield when needed.

We recommend a Wide Vision Safety Mask for use over

eyeglasses or standard safety glasses with side shields,

available at Sears Stores or other Craftsman outlets.

Always use eye protection that is marked to comply with

ANSI Z87ol

Page 3

WARNING: Be sure to read and understand all instructions in this manual

before using the reciprocating saw. Failure to follow all instructions may result in

hazardous radiation exposure, electric shock, fire, and/or serious personal injury_

,_k WARNING: Do not attempt to operate this tool until you have thoroughly

read all instructions, safety rules, and warnings. Failure to comply with them can

result in fire, electric shock, or serious personal injury. Save the manual and refer

to it frequently.

GENERAL SAFETY PRECAUTIONS

WORK AREA SAFETY

mKeep your work area clean and well lit, Do not leave tools or wood scraps

on the saw while it is in operation. Cluttered workbenches and dark areas

invite accidents

Do not operate power tools in explosive environments, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks that

may ignite the dust or fumes.

Keep children and bystanders and visitors away while operating a power

toolo Distractions can cause you to lose control.

Make your workshop childproof with padlocks and master switches. Lock

tools away when they are not in use.

Make sure that the work area has ample lighting so you can see the work

and that there are no obstructions that will interfere with safe operation.

PERSONAL SAFETY

Know your power tool. Read this operator's manual carefully. Learn the

reciprocating saw's applications and limitations, as welt as the specific,

potential hazards related to this tool.

,, Stay alert, watch what you are doing, and use common sense when

operating a power tool.

Do not use a power toot while tired or under the influence of drugs, alcohol,

or medication. A moment of inattention while operating power tools may

result in serious personal injury_

Dress properly. Do not wear loose ctothing or jewelry° Contain tong hair_

Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

Avoid accidental starting of tools. Be sure that the switch is off before

attaching the tool to a power source. Carrying tools with your finger on the

switch or plugging in tools that have the switch "ON" invites accidents.

27224 Manual_Revised 09-0608 Page 4

Remove adjusting keys or wrenches before turning the toot on. A wrench

or a key that is left attached to a rotating part of the tool may result in

personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the tool in unexpected

situations.

Use safety equipment. Always wear eye protection. A dust mask, non-

skid safety shoes, hard hat, and/or hearing protection must be used for

appropriate conditions.

TOOL USE AND CARE

WARNING: Be sure to read, understand, and follow all safety rules and

operating instructions in this manual before using this tool. Failure to do so may

result in electric shock, fire, and/or serious personal injury.

Always use clamps or other practical ways to support and secure the

workpiece to a stable platform. Holding the work by hand or against your

body is unstable and may lead to loss of control.

•Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and more safely at the rate for which is designed.

° Do not use the tool if the switch does not turn it "ON" and "OFF." Any tool

that cannot be controlled with the switch is dangerous and must be repaired_

Disconnect the plug from the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures

reduce the risk of starting the tool accidentally

oNever leave the toot running. Always turn it off. Do not leave the tool until it

comes to a complete stop.

=Store idle tools out of the reach of children and other untrained persons.

Tools are dangerous in the hands of untrained users°

=Maintain tools with care. Keep cutting tools sharp and clean. Properly

maintained tools with sharp cutting edges are less likely to bind and are

easier to control.

Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tool's operation. If damaged, have the

tool serviced before using° Many accidents are caused by poorly maintained

tools.

,, Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

._ WARNING: When using power tools, basic safety precautions should always

be followed to reduce the risk of fire, electric shock, and personal injury_

27224 Manual Revised 09-0608 Page 5

WARNING= The operation of any tool can result in foreign objects being

propelled into your eyes, resulting in severe eye damage. When operating power

tool, always wear safety goggles or safety glasses with side shields and a full

face shield when needed.

,_k WARNING; If any part is missing, do not operate the tool unti! the missing

part has been replaced° Doing so could result in serious personal injury.

ELECTRICAL SAFETY

Double insulated tools are equipped with a

polarized plug (one blade is wider than the other).

This plug will fit into a polarized outlet only one way. If

the plug does not fit into the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to

install a proper outlet°

Avoid contact with grounded surfaces, such as

pipes, radiators, ranges, and refrigerators. There

is an increased risk of electric shock if your body is

grounded.

Do not expose power tools to rain or wet conditions. A wet power tool

will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tool or to pull

the plug out of an outlet. Keep the cord away from heat, oil, sharp edges,

or moving parts. Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

When operating a power tool outdoors, use an outdoor extension cord

that is marked W-A or W. These cords are rated for outdoor use and reduce

the risk of electric shock.

= Replace damaged cords immediately° Using a damaged cord can cause

shock, burns, or electrocution.

If an extension cord is required, use a cord with the proper size of conductor

to prevent excessive voltage drop, loss of power, or overheating. The

following table shows the correct size to use, depending on cord length

and the nameplate amperage rating of the tool. When in doubt, use the next

heavier gauge. Always use UL and CSA listed extension cords.

27224 Manual Revised 09-0608 Page 6

Recommended sizes of extension cords

Ampere Rating Volts

120v

Total Length of Cord in feet

25ft 50ft 100ft 150ft

More Than Not MoreThan AWG

0 6 18 16 I6 14

6 10 18 16 14 !2

10 t2 16 16 14 12

12 16 14 12 Not Recommended

Before connecting the tool to a power source (receptacle, outlet, etc,), be

sure that the voltage supplied is the same as that specified on the nameplate

of the tool. A power source with voltage greater than that specified for the

tool can result in serious injury to the user, as well as damage to the tool.

SAFETY SYMBOLS FOR YOUR TOOL

The label on your tool may include the following symbols.

V ............................................................... Volts

A ................................................................ Amps

Hz .................................................................. Hertz

W.............................................................. Watts

min ............................................................ Minutes

Q_ ............................................................. Alternating Current

-----'=-............................................................. Direct Current

no .............................................................. No-load Speed

[] .............................................................. Class I1construction

.../rain ....................................................... Revolutions or Strokes per minute

._ ............................................................ Indicates danger, warning caution.

It means attention! Your safety is

involved.

SERVICE SAFETY

If any part of this saw is missing or should break, bend, or fail in any

way; or should any electrical component fail to perform properly: shut off the

power switch, remove the saw's plug from the power source, and have the

missing, damaged, or failed part replaced before resuming operation,

Tool service must be performed only at aSears Parts and Repair

Center° Service or maintenance performed by unqualified personnel could

result in a risk of injury.

27224 Manual_Revised_09-O608 Page 7

When servicing atool, use only identical replacement parts. Follow

instructions in the maintenance section of this manual. Use of

unauthorized parts or failure to follow maintenance instructions may create a

risk of electric shock or injury

SPECIFIC SAFETY RULES FOR RECIPROCATING SAW

WARNING: To avoid injury, hold the tool by the insulated gripping surfaces

only. If the tool contacts hidden wiring or its own cord, exposed metal parts

of the too! could shock the operator and cause serious injury. Make sure that

hidden electrical wiring, water pipes, or other hazards are not in the cutting path.

if you are not thoroughly familiar with the operation of a reciprocating

saw, obtain advice from a qualified person.

When servicing, use only identical replacement parts.

Avoid cutting nails and staples when operating with the wood-cutting

blade. Inspect the workpiece carefully and remove all nails and staples

before operation.

Make sure that the blade always extends beyond the shoe and the

workpiece throughout the stroke. Blades may shatter if they strike the

workpiece or shoe.

Do not cut an oversized workpiece.

Check for proper clearance beyond the workpiece before cutting, so that

the blade will not strike the floor, workbench, etc.

Make sure that the blade is not contacting the workpiece before the switch

is turned on,

Keep the saw blade clean and sharp.

Use only correct blades. Always use blades recommended for the type of

workpiece_

Do not leave the tool running, Operate the toot only when hand-held.

Always release the switch to "OFF" and wait for the tool to come to a

complete stop before removing the blade from the workpiece.

Keep the handle dry, clean, and free from oil and grease. Always use

a clean cloth when cleaning. Do not use solvents, brake fluids, gasoline or

other petroleum products to clean the tool; they may damage plastic parts.

Do not operate this tool in agaseous or explosive environment or near

explosive materials.

Never force the tool. Apply firm pressure against the saw's pivot shoe for

the sawing operation--too little or too much pressure could cause jumping or

vibration and may break the blade.

27224 Manual_Revised_09-0608 Page 8

o Never operate the saw without the pivot shoe in position. The spindle may

strike against the workpiece and damage the reciprocating mechanism.

o Do not touch the blade or the workpiece immediately after the sawing

operation. They may be extremely hot and could burn your skin.

o Hold the tool firmly with two hands when operating the tool.

o Do not reach underneath the workpiece, The proximity of the blade to your

hand is hidden from your sight..

o Hold tool by the insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord.

WARNING: Your saw should never be connected to the power source when

you are assembling parts, making adjustments, installing or removing blades,

cleaning, or when it is not in use, Disconnecting the reciprocating saw will

prevent accidental starting, which could cause serious personal injury.

When unpacking the box, do not discard any packing materials until all of the

contents are accounted for:

Carefully lift the reciprocating saw out of the carton and place it on a stable,

flat surface,

2. Open the parts bag to locate the following:

o ! scrolling wood-cutting blade

° Operator's manual

3. Inspect the items carefully to make sure that no breakage or damage has

occurred during shipping. If any of the items mentioned is missing, (refer to

"PARTS LIST" illustration), return the reciprocating saw to your nearest Sears

store or Craftsman outlet to have the missing parts replaced.

,_ WARNING: If any part is broken or missing, do not attempt to assemble the

reciprocating saw, plug in the power cord, or operate the saw until the broken

or missing part is are replaced° Failure to do so could result in possible serious

injury.

27224 Manual Revised_09-0608 Page 9

CARTON CONTENTS/LOOSE PARTS (Fig. 1)

Fig. '1

Scrolling wood-cutting blade

KNOW YOUR SCROLLING RECIPROCATING SAW (Fig, 2)

Before attempting to use this scrolling reciprocating saw, familiarize yourself

with all of its operating features and safety requirements.

,_ WARNING= Do not allow familiarity with your reciprocating saw to make you

careless. Remember that a careless fraction of a second is sufficient to inflict

severe injury.

Fig. 2 3-position mode selector Variable-

de-clamp

Pivot shoe lever

Toot-less

: t¢/ blade

,=.____________________M_[_ ___ clamp

Shoe-release button

Scrolling

saw

head

trigger

switch

Live-Tool Indicator

27224 Manual_Revised._09-0608 Page 10

Inhaltsverzeichnis

Andere Craftsman Gesehen Handbücher

Craftsman

Craftsman 875.199530 Bedienungsanleitung

Craftsman

Craftsman 137.216021 Bedienungsanleitung

Craftsman

Craftsman 172.26672 Bedienungsanleitung

Craftsman

Craftsman Lithium 320.28127 Bedienungsanleitung

Craftsman

Craftsman 315.271030 Bedienungsanleitung

Craftsman

Craftsman 113.235300 Bedienungsanleitung

Craftsman

Craftsman 286.26829 Bedienungsanleitung

Craftsman

Craftsman 103.22880 Gebrauchs- und Pflegehandbuch

Craftsman

Craftsman 137.21825 Bedienungsanleitung

Craftsman

Craftsman 152.221240 Bedienungsanleitung

Craftsman

Craftsman 113.198411 Operators Bedienungsanleitung

Craftsman

Craftsman 11579 - C3 19.2 Volt DieHard Reciprocating... Bedienungsanleitung

Craftsman

Craftsman 320.10860-01 Bedienungsanleitung

Craftsman

Craftsman Contractor 113.29884 Bedienungsanleitung

Craftsman

Craftsman 172.10853 Bedienungsanleitung

Craftsman

Craftsman 351.224400 Bedienungsanleitung

Craftsman

Craftsman 137.218760 Bedienungsanleitung

Craftsman

Craftsman 315.216090 Bedienungsanleitung

Craftsman

Craftsman 113.236090 Bedienungsanleitung

Craftsman

Craftsman 113.196421 Bedienungsanleitung

Craftsman

Craftsman 315.212240 Bedienungsanleitung

Craftsman

Craftsman 315.28462 Bedienungsanleitung

Craftsman

Craftsman 320.2190 Bedienungsanleitung

Craftsman

Craftsman 315.214770 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung