CREE LIGHTING SYRIUS SYS-A Series Bedienungsanleitung

SYRIUS™

Street Lights Luminaires

Includes: Syrius™

DISASSEMBLY INSTRUCTIONS

Tools:

N° DOC: DI122RLER0 Rev: 01 Latest Release Date: 18/11/2021

Models :

Syrius Codici LS Codici DR

SYS-A-###

SYS-B-###

LEA### PH###

Warning: Before opening the appliance, remove voltage from the mains line

Disassembly Instructions

Light Source (LS)

For end User (EU)

LS-EU

1.Follow the points: A - B - C - D of the instructions in

paragraph PS-CA

2.Unscrew in order the screws 1, 2, 3, 4 and 5 of the

optical group

3.Remove optical unit 8 with heatsink 7, cutting the ca-

ble tie that blocks the cable and pulling the cable

through gasket 9

4.If damaged, remove gasket 9 and replace it with a new

one

5.Pass the cable of the new optical unit with heatsink

through gasket 9

6.Screw back in order the screws 1, 2, 3, 4 and 5 of the

optical group with a torque of 2.8 Nm

7.Reconnect disconnected cables to points C and D of the

instructions in paragraph PS-CA

8.Restore the cable tie removed in step 3

9.Screw back 6 screws with a torque of 2 Nm

N° DOC: DI122RLER0 Rev: 01 Latest Release Date: 18/11/2021

Disassembly Instructions

Light Source (LS)

For Control Authority (CA)

LS -CA

i. Follow points 1 - 2 - 3 - 4 of the instructions in

paragraph LS -EU

ii.Unscrew the screws 10 between optical group 8

and heatsink 7

iii.Pass the cable through gasket 11

iv.Separate heatsink 7 from optical unit 8

Disassembly Instructions

Power Supply (PS)

For End User (EU)

PS-EU for SYS-A-##:

a.Follow the points: A - B - C - D of the instructions

in paragraph PS-CA

c.Disconnect the remaining cables connected to the

luminaire body if any (NEMA, Zhaga)

d.Separate the plug from the connector socket 12

e.Remove the wiring plate 13 by unscrewing the

screw 14

f.Insert the new plate into the joints and screw

back on 14

g.Reconnect the plug and socket of connector 12

h.Reconnect the disconnected cables at points "a"

and "b" (see attached wiring diagrams)

i. Lower the support rod 17 while holding the door

j.Close the door and screw the two tool free screws

to a torque of 2 Nm

SYS-A

Disassembly Instructions

Power Supply (PS)

For End User (EU)

PS-EU forSYS-B:

a.Follow the points: A - B - C - D of the instructions in para-

graph PS-CA

c.Disconnect the remaining cables connected to the luminaire

body if any (NEMA, Zhaga)

d.Hold the driver still and unscrew the fixing screws 19

e.Insert the new driver by screwing the fixing screws 19

f.Reconnect the disconnected cables at points "a" and "b" (see

attached wiring diagrams)

g.Lower the support rod 17 while holding the door up

h.Close the door and screw the 6 screws to a torque of 2 Nm

For Control Authority (CA) PS-CA

A.Unscrew 6 screws to open the wiring compartment

B.Secure the door with the appropriate support rod 17

C.Disconnect the ground cable from the LED bar on the

heatsink 7 from connector 15

D.Disconnect the line and neutral cables from the led plate on

the heatsink 7 from the driver terminal block 16 using a

screwdriver

E.Disconnect the remaining cables connected to the driver on

your terminal block 16 with a screwdriver

F.Hold the driver in place and unscrew fixing screws 18 (for

SYS-A-#) or 19 (for SYS-B-#)

G.Extract the driver

N° DOC: DI122RLER0 Rev: 01 Latest Release Date: 18/11/2021

Disassembly Instructions

End of Life (EL)

Light Source (LS) Follow instructions in the paragraph LS-CA

Power Supply (PS) Follow instructions in the paragraph PS-CA

DIRECTIVE 2012/19/EU (WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT – WEEE): Information for users.

This product complies with EU Directive 2012/19/EU. The crossed-out wastebasket symbol on the appliance means that at the end of its useful lifespan, the product must be disposed

of separately from ordinary household wastes. The user is responsible for delivering the appliance to an appropriate collection facility at the end of its useful lifespan. Appropriate se-

parate collection to permit recycling, treatment and environmentally compatible disposal helps prevent negative impact on the environment and human health and promotes recycling

of the materials making up the product. For more information on available collection facilities, contact your local waste collection service or the shop where you bought this appliance.