Crestron FlipTop FT2 Series Bedienungsanleitung

The Crestron® FT2-700-MECH-PTL FlipTop™ cable management system

installs into a table or other horizontal surface to provide modular

connectivity. It features a retracting lid that disappears within the

enclosure. When the lid is retracted, 12 module slots are arranged in two

rows of six. The flexible modular design may also be customized with an

assortment of Crestron accessories, and the pass-through lid style

allows cables to be fully extended while the lid is closed.

For more information about the accessories, please visit

www.crestron.com/Crestron-FlipTops. To configure your FlipTop, launch

the FlipTop Configuration Tool.

In the Box

1FT2-700-MECH-PTL

Additional Items

3 Locking Bars with screws and gaskets (4532479)

1Cutout Template (4527491)

FT2-700-MECH-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Mechanical, Pass-Through Lid

Mount the FlipTop Assembly

A mounting hole is required for an FT2-700-MECH-PTL installation. Use

the included template to cut a mounting hole for new installations. The

FT2-700-MECH-PTL may also replace an FT-600 FlipTop or Extron®

Cable Cubby® 700 Cable Access Enclosure using the existing mounting

hole.

When determining the location for the FT2 assembly, consider where

users will be seated and their proximity to the FT2 assembly's modules

and retractors. Refer to the FT2A-CBLR-GR series cable retractors for

above-the-table cable pull-out lengths.

For a new mounting, follow sections Cut the Mounting Hole and Secure

the FlipTop Assembly. To use the mounting hole of an existing FT-600

FlipTop assembly, follow sections Replace the FT-600 FlipTop Assembly

and Secure the FlipTop Assembly.

Cut the Mounting Hole

A saw and the included cutout template are required to cut the

mounting hole.

1. Check the table surface and the area beneath the table. Clear any

obstructions that may impede the installation or functionality of the

FT2 assembly, retractors, and accessories.

2. Using the included cutout template, trace an outline of the mounting

hole onto the table.

3. Cut the mounting hole in the table with an appropriate saw.

Replace the FT-600 FlipTop Assembly

The FT-600 FlipTop assembly mounting hole is larger than the mounting

hole required for the FT2 assembly. FT2A-SPCR-MNT-10 plastic spacers

(sold separately) are used to help fill the gap between the mounting hole

and the FT2 assembly.

1. Loosen the four socket screws that secure the two mounting plates

and the FT-600 FlipTop assembly to the surface.

2. Remove the FT-600 FlipTop assembly.

3. Attach the four plastic spacers to each corner of the

FT2-700-MECH-PTL.

4. To continue mounting the FT2-700-MECH-PTL, refer to Secure the

FlipTop Assembly.

FT2-700-MECH-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Mechanical, Pass-Through Lid

Secure the FlipTop Assembly

To secure the FT2-700-MECH-PTL to the table surface:

1. Gently remove the bezel before securing the FT2 assembly to the

table. It is held in place with magnets.

2. Ensure that all four swiveling dogs are tucked inside of the FT2

assembly, and then insert the FT2 assembly into the mounting hole

until the top lip is flush with the table surface.

3. Carefully tighten the four swiveling dogs in each corner of the FlipTop

assembly clockwise until the FT2 assembly is secured in place against

the table. Do not overtighten the swiveling dogs.

CAUTION: A screwdriver or manual torque screwdriver at its lowest

setting may be used to tighten the swiveling dogs. Avoid stripping

the swiveling dogs and damaging the table.

If removing the FT2-700-MECH-PTL from the table, ensure that

the screwdriver rotation is set correctly before loosening the

swiveling dogs.

Install the Modules

All modules are sold separately and not included with the

FT2-700-MECH-PTL FlipTop assembly. Installation procedures for most

modules are available in separate product documentation. For more

information, refer to the specific product manual located at

www.crestron.com/manuals.

The following sections provide best practices and installation procedures

for pass-through cable modules and blank plate modules.

Module Best Practices

Follow the best practices below when performing module installation.

lPerform module installation in the following order:

1. AC Power Outlet Modules (FT2A-PWR-US,FT2A-PWR-EU,

FT2A-PWR-AU,FT2A-PWR-FR,FT2A-PWR-IS,FT2A-PWR-IT,

FT2A-PWR-SW,FT2A-PWR-UK, and FT2A-PWR-UN)

2. Retractor modules (FT2A-CBLR-GR series)

3. All other modules (FT2A-CP series, FT2A-CHGR series,

FT2A-PLT-PT, and FT2A-PLT-BLANK)

lPlace the FT2A-CBLR-GR modules only at the ends of a module row.

lDress all cables after installing each module.

Pass-Through Cable Module

The FT2A-PLT-PT pass-through modules (sold separately) enable

FT2-CBL-PT pass-through cables (sold separately) and other types of

interface cables to be installed within the FT2-700-MECH-PTL. Each

FT2A-PLT-PT cable module is packaged with a nylon grommet and a

cable plate. An empty module slot in the FT2-700-MECH-PTL and an

FT2-CBL-PT series or other interface cable are required for installation.

FT2-700-MECH-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Mechanical, Pass-Through Lid

Installing the Pass-Through Cable Module with 4K Cables

The included grommet is not needed when installing most 4K cables. If

the cable is 10 mm or thinner, the grommet may be used.

1. Push the connector end of the cable through the hole in the cable

plate.

2. Insert the cable plate into one of the three slots in the pass-through

module. Choose the appropriate slot based on the length of the cable

connector. The top of the connector must sit flush with the top of the

module.

NOTES:

lIf the connector extends past the top of the pass-through

module, the lid cannot close.

lEnsure that the cable moves freely in the module prior to

attaching the side plate. The plate is difficult to remove once it is

attached.

3. Attach the side plate to the module by snapping the plastic clips on

the plate into the two slots on the module.

NOTE: When removing the side plate, use a flat-head screwdriver to

carefully pry the plastic clips off of the module near the two slots.

4. Feed the other end of the cable through an empty module slot in the

FT2 assembly.

5. Slide the pass-through cable module into the same module slot as

mentioned in the previous step. Use the guide ribs on the front and

rear of each module to help position the module in the FT2 assembly.

Installing the Pass-Through Cable Module with Non-4K

Cables

The grommet is recommended to use with cables that are 10 mm or

thinner.

1. Open the grommet.

2. Insert a cable into the grommet with the connector facing up toward

the user.

3. Press the grommet back together to secure the cable inside.

4. Push the grommet and cable through the hole in the cable plate.

FT2-700-MECH-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Mechanical, Pass-Through Lid

5. Insert the cable plate into one of the three slots in the pass-through

module. Choose the appropriate slot based on the length of the cable

connector. The top of the connector must sit flush with the top of the

module.

NOTES:

lIf the connector extends past the top of the pass-through

module, the lid cannot close.

lEnsure that the cable moves freely in the module prior to

attaching the side plate. The plate is difficult to remove once it is

attached.

6. Attach the side plate to the module by snapping the plastic clips on

the plate into the two slots on the module.

NOTE: When removing the side plate, use a flat-head screwdriver to

carefully pry the plastic clips off of the module near the two slots.

7. Feed the other end of the cable through an empty module slot in the

FT2 assembly.

8. Slide the pass-through cable module into the same module slot as

mentioned in the previous step. Use the guide ribs on the front and

rear of each module to help position the module in the FT2 assembly.

FT2-700-MECH-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Mechanical, Pass-Through Lid

Install the Blank and Keystone Plate Module

Blank plate modules (sold separately) fill empty slots in module rows,

and keystone plate modules (sold separately) allow for cables

terminated with standard keystone jacks to be installed in the FT2

assembly. The blank and keystone modules each require one empty

module slot for installation.

To install a blank or keystone plate module into the

FT2-700-MECH-PTL:

lSlide the blank plate module down into the appropriate module slot.

Use the guide ribs on the front and rear of each module to help

position it in the FT2 assembly.

lFor the keystone plate module, complete the following steps.

1. Snap the cable’s keystone jack into the keystone opening in the

keystone plate module.

2. Feed the cable down through the empty module slot.

3. Slide the attached keystone plate module down into the same

module slot using the front and rear guide ribs to assist with

positioning.

Install the Locking Bars

To install the locking bars:

1. Position the locking bars so that the gasket and screws attached to

the locking bars engage the screw holes in the FT2 assembly.

2. Use a screwdriver to secure the locking bar screws to the FT2

assembly.

CAUTION: Do not overtighten the locking bar screws.

FT2-700-MECH-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Mechanical, Pass-Through Lid

Install the Bezel

Place the bezel onto the FT2 assembly so that the retractable lid fits

inside the bezel opening. The bezel is held in place using magnets.

Operate the FlipTop Assembly

To operate the FT2-700-MECH-PTL:

1. Open the lid by sliding the lid retraction button away from the FT2

assembly. The lid retracts into the assembly.

2. Access the modules in the FT2 assembly.

3. Close the lid by lifting it vertically and returning it over the FT2

assembly.

Visit the Product Page

Scan the QR code to visit the product page.

FT2-700-MECH-PTL

www.crestron.com/model/6511980

FT2-700-MECH-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Mechanical, Pass-Through Lid

Additional Information

Original Instructions

The U.S. English version of this document is the original instructions.

All other languages are a translation of the original instructions.

Regulatory Models: FT2-700-MECH-AL, FT2-700-MECH-B

Crestron product development software is licensed to Crestron dealers and Crestron

Service Providers (CSPs) under a limited nonexclusive, nontransferable Software

Development Tools License Agreement. Crestron product operating system software is

licensed to Crestron dealers, CSPs, and end-users under a separate End-User License

Agreement. Both of these Agreements can be found on the Crestron website at

www.crestron.com/legal/software_license_agreement.

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at

www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, visit

www.crestron.com/opensource.

Crestron, the Crestron logo, and FlipTop are either trademarks or registered trademarks

of Crestron Electronics, Inc. in the United States and/or other countries. Cable Cubby is

either a trademark or registered trademark of Extron Electronics in the United States

and/or other countries. Extron is either a trademark or registered trademark of RGB

Systems, Incorporated in the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this document to refer to either

the entities claiming the marks and names or their products. Crestron disclaims any

proprietary interest in the marks and names of others. Crestron is not responsible for

errors in typography or photography.

Doc. 9077A

11/05/21

FT2-700-MECH-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Mechanical, Pass-Through Lid

Andere Handbücher für FlipTop FT2 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Crestron Konferenzsystem Handbücher

Crestron

Crestron UC-C160-T Bedienungsanleitung

Crestron

Crestron UC-C160-T Bedienungsanleitung

Crestron

Crestron UC-MX70-Z Bedienungsanleitung

Crestron

Crestron HT-CAM Bedienungsanleitung

Crestron

Crestron CCS-UC-1-X Bedienungsanleitung

Crestron

Crestron UC-MX70-NC-T Bedienungsanleitung

Crestron

Crestron Mercury CCS-UC-1 Maßzeichnung

Crestron

Crestron Horizon HZ-FP-G Series Bedienungsanleitung

Crestron

Crestron UC-M70-NC-T Bedienungsanleitung

Crestron

Crestron UC-2-Z Bedienungsanleitung

Crestron

Crestron Zoom Rooms Bedienungsanleitung

Crestron

Crestron UC-M50-Z-UPGRD Bedienungsanleitung

Crestron

Crestron UC-BX31-T Bedienungsanleitung

Crestron

Crestron UC-BX31-T-WM-INDIA Bedienungsanleitung

Crestron

Crestron UC-B160-T Bedienungsanleitung

Crestron

Crestron UC-BX30-T Bedienungsanleitung

Crestron

Crestron UC-CX100-T Bedienungsanleitung

Crestron

Crestron UC-SB1-CAM Bedienungsanleitung

Crestron

Crestron UC-C100-T-WM Bedienungsanleitung

Crestron

Crestron Flex UC-MM30-Z Bedienungsanleitung

Crestron

Crestron UC-M70-U Bedienungsanleitung

Crestron

Crestron UC-BX31-T-WM Bedienungsanleitung

Crestron

Crestron UC-MX70-T Bedienungsanleitung

Crestron

Crestron CCS-UC-250 Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Inmarsat

Inmarsat mini M Bedienungsanleitung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung

AXIWI

AXIWI AT-350 Bedienungsanleitung