Crestron CNWM-LT9 Bedienungsanleitung

CRESTRON CNWMBG-10A Wall-Mount Wired Panels

REMOTE CONTROL SYSTEMS

1 DOC. 8078

Specifications subject to change without notice.

DESCRIPTION:

The CNWMBG-10A wired panel, illustrated in figure 1, interfaces with a CRESNET II control system over

theCRESNETIInetwork.Thepaneluses10miniaturepushbuttonswithself-containedfeedbackLEDsand

includes a standard bargraph. The CNWMBG-10A is designed for wall-mounting using a standard single-

gangelectricalbox.Custompanelfinishes,engraving,colored button caps, and theomissionof unused

buttons are all standard.

1

3

5

7

910

8

6

4

2

CRESTRON

Figure 1. CNWMBG-10A, Wall-Mount Wired Panel

INSTALLATION/SETUP:

Identity Code

Eachunique panel or component on the CRESNET II network requires thesettingof an identity code (ID

CODE). ID CODES are two-digit hexadecimal numbers, from 10 to FE.

TheID CODE of thepanelshould be set tomatch the ID CODE specifiedin the NET.ID statement ofthe

CRESNET II SIMPL-C program referencing the panel (refer to SYNTAX section). To set an ID CODE,

disconnect power. Accessible through the back cover are two miniature circuit-mounted rotary

switches, identified as H and L. These 16-position hexadecimal switches can be set to 0 through F. Using

a small screwdriver, rotate the arrow in the center of the switch marked H so that it points to the first

(or most-significant) digit or letter of the specified ID CODE. Set the switch marked L to the second

(least-significant) digit or letter of the specified ID CODE.

CRESTRON CNWMBG-10A Wall-Mount Wired Panels

REMOTE CONTROL SYSTEMS

2 DOC. 8078

Specifications subject to change without notice.

Preparation for Use

The 4-pin connector marked NET must be wired to the CRESNET II network. Network termination points

are available at the control system power supply. Network units may also be daisy-chained together.

Refer to the latest revision of CNPWS power supplies (Docs. 8017 and 8091) in the CRESNET II manual

forwire gauge specifications and connection detail.

PROGRAMMING:

Thepaneldrawinginfigure1showsthelocationoftheSIMPL-Cbuttonnumbersandtheircorresponding

buttonpositions. Buttons or bargraphs which arenotused need not be assignedasignal name.

SYNTAX:

Thefollowingsyntaxcodesareprovidedforcompatibilitypurposesonly.

NET.ID <10 to FE>: CNWP

i1,o1 = <signal name> \ button and LED combined

i2 = <signal name> \ independent button

o2 = <signal name> \ independent LED

" = " "

i10 = <signal name>

o10 = <signal name>

<BAR1> = <signal name> \ first bargraph level

FURTHER INQUIRIES:

If after reviewing this Operations Guide you still have additional questions, please contact a CRESTRON

technical support representative by dialing (800) 237-2041 or (201) 894-0660.

Inhaltsverzeichnis

Andere Crestron Rack & Stand Handbücher

Crestron

Crestron BB-1000 Bedienungsanleitung

Crestron

Crestron TMK-1000L Bedienungsanleitung

Crestron

Crestron PMK-1000L Bedienungsanleitung

Crestron

Crestron MMK-1000L Bedienungsanleitung

Crestron

Crestron CCS-UC-200-WSTND Bedienungsanleitung

Crestron

Crestron RMK-1500 Bedienungsanleitung

Crestron

Crestron CNWMBG2-34A Bedienungsanleitung

Crestron

Crestron CAEN-CK Bedienungsanleitung

Crestron

Crestron TMK-15L Bedienungsanleitung

Crestron

Crestron WMKB-1000L Bedienungsanleitung

Crestron

Crestron TSW-560 Bedienungsanleitung

Crestron

Crestron RMK-3100L Bedienungsanleitung

Crestron

Crestron RMK-1600 Bedienungsanleitung

Crestron

Crestron Mud Ring Mount Kit for Cameo 2 MMK-CBF-T Bedienungsanleitung

Crestron

Crestron TSW-UMB-70-BBI Bedienungsanleitung

Crestron

Crestron PMK-15L Bedienungsanleitung

Crestron

Crestron CPC-TMT Anleitung zur Verwendung

Crestron

Crestron MK-QM-RMCRX Bedienungsanleitung

Crestron

Crestron RMK-8L Bedienungsanleitung

Crestron

Crestron TMK-3100L Bedienungsanleitung

Crestron

Crestron UCA-SMK-UC2 Bedienungsanleitung

Crestron

Crestron MMK-15L Bedienungsanleitung

Crestron

Crestron CPC-WMT Anleitung zur Verwendung

Crestron

Crestron RMK-6L Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung