Cross Technologies 2115-122 Bedienungsanleitung

Instruction Manual Model 2115-122

Block Upconverter

May 2009 Rev 0

MODEL 2115

CROSS TECHNOLOGIES INC.

POWER

UPCONVERTER

EXT

10MHZ

ALARM

Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,

but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.

for purposes of operating the equipment.

When ordering parts from Cross Technologies, Inc., be sure to include the equipment

model number, equipment serial number, and a description of the part.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

INSTRUCTION MANUAL

MODEL 2115-122 Block Upconverter

TABLE OF CONTENTS PAGE

Warranty 2

1.0 General 3

1.1 Equipment Description 3

1.2 Technical Characteristics 4

2.0 Installation 5

2.1 Mechanical 5

2.2 Rear Inputs and Outputs 6

2.3 Front Panel Indicators 6

2.4 Operation 7

2.5 Environmental Information 8

WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.

All Cross Technologies, Inc. products are warranted against defective materials and

workmanship for a period of one year after shipment to customer. Cross Technologies,

Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s

option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall

not be liable for any special, indirect, or consequential damages. This warranty does not

cover parts or equipment which have been subject to misuse, negligence, or accident by the

customer during use. All shipping costs for warranty repairs will be prepaid by the

customer. There are not other warranties, express or implied, except as stated herein.

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2115-122 Manual, Rev. 0 Page 2 5/04/09

MODEL 2115-122 Block Upconverter

1.0 General

1.1 Equipment Description

The 2115-122 Block Upconverter converts 0.95 - 1.45 GHz to 12.2 - 12.7 GHz with low phase noise and flat

frequency response. Frequency translation is via a 11.25 GHz local oscillator. Front panel LEDs provide

indication of DC Power, External 10 MHz, and PLL Alarm. The gain is +20 dB. Connectors are SMA female

for the RF and BNC female for the L-Band and external reference input and reference output. A three-way

switch controls which 10 MHz reference is being used. In the INT position, the internal reference is used, in

the EXT position, the external reference is used, and in the AUTO position, the internal reference is used unless

a 3 dBm ± 3 dB, 10MHz reference signal is connected to the external reference input. The 2115 is powered by

a 100-240 ± 10% VAC power supply, and mounted in a 1 3/4” X 19 “ X 14” rack mount chassis.

MODEL 2115

CROSS TECHNOLOGIES INC.

POWER

UPCONVERTER

EXT

10MHZ

ALARM

FRONT PANEL

GND

EXT 10MHZ

RF OUTPUT

INPUT

10MHZ REF

OUTPUT

INT

EXT

AUTO

L-BAND

INPUT

J101

J11

ALARM

REAR PANEL

FIGURE 1.1 Front and Rear Panels

Block Diagram

12.2

12.7

GHz

OUT

0.95

1.45

GHz

11.25

GHz

12.2 to 12.7 GHz

EXT 10MHZ

10 MHZ

MON

2 GHz LP

AUTO

INT

10MHZ

FIGURE 1.2 Model 2115-122 Upconverter Block Diagram

2115-122 Manual, Rev. 0 Page 3 5/04/09

1.2 Technical Characteristics

TABLE 1.0 2115-122 Upconverter Specifications*

Input Characteristics

Impedance/Return Loss 50 Ω/14 dB

Frequency 0.95 to 1.45 GHz

Noise Figure, max. 20 dB, max gain

Input Level -40 to -20 dBm

Input 1dB Compression -10 dBm

Output Characteristics

Impedance/Return Loss 50 Ω/14 dB

Frequency 12.2 to 12.7 GHz

Output Level Range -20 to -5 dBm

Output 1dB Compression +10 dBm

Channel Characteristics

Gain +20 dB ± 1 dB

Image Rejection > 60 dB, min

Spurious, Inband Signal Related <-60 dBC in band, Signal Independent, <-60 dBm

Spurious, Out of Band < -50 dBm

Intermodulation < -55 dBC for two carriers each at -10 dBm out

Frequency Response ±1 dB, 12.2 to 12.7 GHz out; ± 0.5 dB, 40 MHz BW

Frequency Sense Non-inverting

LO Characteristics

LO Frequency 11.25 GHz

Frequency Accuracy ± 0.01 ppm max over temp internal reference, external reference input

10 MHz Level 3 dBm, ± 3 dB, 75ohms, External In or Internal out

-110

-100

-90

-80

-70

1MHz

100kHz

10kHz

1kHz

100Hz

dBC/Hz

Phase Noise @ Freq

Controls, Indicators

Ext 10 MHz Yellow LED, Indicates Ext 10 MHz reference is selected

(rear panel DPDT switch)

PLL Alarm Red LED, External contact closure

Power Green LED

Other

RF In Connector SMA (female), 50Ω

L-Band connector BNC (female) 50Ω, (BNC, 75Ω; Type-F, 75Ω; Type-N, 50Ωoptional)

10 MHz Connectors BNC (female) 75Ω

Alarm Connector DB9, female - NO or NC contact closure on Alarm

Size 19 inch, 1RU standard chassis 1.75”high X 14.0” deep

Power 100-240 ±10% VAC power supply, 47-63 Hz, 45 watts max

Options

Connector options see TABLE 2.2

*+10˚C to +40˚C; Specifications subject to change without notice.

2115-122 Manual, Rev. 0 Page 4 5/04/09

2.0 Installation

2.1 Mechanical

The 2115-122 consists of a PCB and an RF assembly housed in a 1 RU (1 3/4 inch high) by 12 inch deep

chassis. A switching, ± 12, +24, +5 VDC power supply provides power for the assemblies. The 2115-122 can

be secured to a rack using the 4 holes on the front panel. Figure 2.0 shows how the 2115-122 is assembled.

PS IN

PIN 1, +12 VDC

PIN 2, +5 VDC

PIN 3, +5 VDC

PIN 4, GROUND

PIN 5, GROUND

PIN 6, -12 VDC

PIN 7, +24 VDC

PIN 8, +24 VDC

POWER

SUPPLY

J10

J101 - Panel Mount

SMA Connector

PLL

VCO

MIXER

AMP

BP FILTER

ISO

FIGURE 2.0 2115-122 Mechanical Assembly

2115-122 Manual, Rev. 0 Page 5 5/04/09

2.2 Rear Panel Input/Output Signals - Figure 2.1 shows the input and output connectors on the rear panel.

GND

EXT 10MHZ

RF OUTPUT

INPUT

10MHZ REF

OUTPUT

INT

EXT

AUTO

L-BAND

INPUT

J101

J1 - L-BAND INPUT

BNC (female) 50 Ω. 0.95 to 1.45 GHz

20 dBm max input signal. See Table

2.2 for other connector options.

AC INPUT

120-240 ±10%VAC, 47-60 HZ

Uses 2 amp Slow Blo, 5mm

fuse

S1 - 10MHZ SWITCH

3-position switch. INT selects internal 10MHz ref.

AUTO selects internal 10MHz ref, unless a 0dBm

±3dB 10MHz signal is inserted on J2. EXT selects

external 10MHz ref from J2.

J1 - EXT 10MHZ INPUT

BNC (female) 75 Ω. Insert external

10MHz reference here (3 dBm ± 3

dB).

J101 - RF OUTPUT

Type N (female) 50 Ω.

12.2 to 12.7 GHz, -20 to -5 dBm max

output signal. See Table 2.2 for other

connector options.

J11 - ALARM

DB9 (female) connector.

See Table 2.1.

J8 - 10MHZ REF OUTPUT

BNC (female) 75 Ω. Outputs currently

selected 10MHz ref signal (3 dBm ±3 dB).

J11

ALARM

FIGURE 2.1 2115-122 Rear Panel I/Oʼs

TABLE 2.1 J11 Pinouts (DB9)

Pin Function

1 Not Used

2 Not Used

3 Not Used

4 Not Used

5 GND

6 Alarm Relay: Common

7 Alarm Relay: Normally Open

8 Not Used

9 Alarm Relay: Normally Closed

TABLE 2.2 Connector Options

Option RF L-Band

SN SMA, 50ΩType N, 50Ω

SS SMA, 50ΩSMA, 50Ω

2.3 Front Panel Indicators -The following are the front panel indicators.

DS2 - ALARM LED

Lights RED when PLL comes

out of lock.

DS1 - POWER LED A

Lights GREEN when DC

voltage is present from AC

power supply.

DS3 - EXT 10MHZ LED

Lights YELLOW when external

10MHz reference is active.

MODEL 2115

CROSS TECHNOLOGIES INC.

POWER

UPCONVERTER

EXT

10MHZ

ALARM

FIGURE 2.2 2115-122 Front Panel Controls and Indicators

2115-122 Manual, Rev. 0 Page 6 5/04/09

2.4 Installation / Operation

2.4.1 Installing and Operating the 2115-122 Upconverter

1. Connect a -20 dBm to -5 dBm 0.95 to 1.45 GHz signal to L-BAND INPUT, J1 (Figure 2.1).

2. Connect the RF OUTPUT, J101, to the external equipment.

3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC connector on the back panel.

4. Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.2).

5. Select either INT (for internal 10MHz ref), AUTO (for internal 10MHz ref UNLESS a external

10MHz, +3 dBm signal is connected to J2), or EXT (for external 10MHz, +3 dBm ref that is inserted at

J2) on rear panel switch S1 (Figure 2.1).

6. If EXT is selected or AUTO is selected and there is a 10MHz, +3 dBm signal at J2, check that DS3

(yellow, Ext 10MHZ) is on (Figure 2.2).

7. Check that a 10MHz, +3 dBm ±3 dB signal is present at the 10MHZ REF OUTPUT (J8) (Figure 2.1).

8. AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot in the

drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot. If a fuse

continues to open, the power supply is most likely defective.

FUSE DRAWER

SPARE FUSE DRAWER

AC Fuse - 2 amp slow blow (Type T),

5 mm X 20 mm

INPUT

100-240 VAC

47-63 Hz

2A MAX

FUSE

TYPE T 2A

250 VOLT

FOR 100 - 240 V~

FIGURE 2.3 Fuse Location and Spare Fuse

2115-122 Manual, Rev. 0 Page 7 5/04/09

2.5 Environmental Use Information

A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions

located in the user manual furnished by the manufacturer of your equipment rack.

B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition

does not exist due to uneven weight distribution.

C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack may be greater than room ambient temperature.

Therefore, consideration should be given to Tmra.

D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow

required for safe operation of the equipment is not compromised. Additional space between unit

may be required.

E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of circuits could have on over current protection and supply wiring.

Appropriate consideration of equipment name plate rating should be used, when addressing this concern.

F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connection to the Branch

(use of power strips).

G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.

If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED

prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS

emission problems.

2115-122 Manual, Rev. 0 Page 8 5/04/09

CROSS TECHNOLOGIES, INC.

6170 Shiloh Road

Alpharetta, Georgia 30005

(770) 886-8005

FAX (770) 886-7964

Toll Free 888-900-5588

WEB www.crosstechnologies.com

E-MAIL [email protected]

2115-122 Manual, Rev. 0 Page 9 5/04/09

Inhaltsverzeichnis

Andere Cross Technologies Medienkonverter Handbücher

Cross Technologies

Cross Technologies 2416 25 Series Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-0923 370 Series Bedienungsanleitung

Cross Technologies

Cross Technologies 2015-05 Bedienungsanleitung

Cross Technologies

Cross Technologies 2015-58T Bedienungsanleitung

Cross Technologies

Cross Technologies 2415 0925 Series Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-1727-140 Bedienungsanleitung

Cross Technologies

Cross Technologies 2099-2424 Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-93 Bedienungsanleitung

Cross Technologies

Cross Technologies 2015-03A Bedienungsanleitung

Cross Technologies

Cross Technologies 4115-41-212 Bedienungsanleitung

Cross Technologies

Cross Technologies 2005-10 Bedienungsanleitung

Cross Technologies

Cross Technologies 2117-9395 Bedienungsanleitung

Cross Technologies

Cross Technologies 4117-14 Bedienungsanleitung

Cross Technologies

Cross Technologies 1584-29 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-95 Bedienungsanleitung

Cross Technologies

Cross Technologies 4116-285-2450 Bedienungsanleitung

Cross Technologies

Cross Technologies 4115-300 Bedienungsanleitung

Cross Technologies

Cross Technologies 3116-192 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-116 Bedienungsanleitung

Cross Technologies

Cross Technologies 3116-7786-2150 Bedienungsanleitung

Cross Technologies

Cross Technologies 2017-14 Bedienungsanleitung

Cross Technologies

Cross Technologies 2016-1522 Bedienungsanleitung

Cross Technologies

Cross Technologies 2116-182193 Bedienungsanleitung

Cross Technologies

Cross Technologies 2416 02I Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung