Crux RVCCH-75F Bedienungsanleitung

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

DODGE

2015 - 2015 Challenger

2011 - 2014 Charger

2011 - 2017 Journey

CHRYSLER

2011 - 2014 300c

FIAT

2011 - 2014 Freemont

APPLICATION NOTES:

THIS INTERFACE REQUIRES THE

VEHICLES TO HAVE A 4.3” OR

WORKS FOR:

U-Connect 4.3 and 8.4” Screens

This interface does not o er the

Force RVC feature.

PARTS INCLUDED

(1) CH-75F Main Interface Module

SW: Ver 25-140729-140506

(1) CH-75F CAN (Small) Module

SW: 140506

(1) CH-75F 22-Pin T-Harness

(1) CH-75F LVDS T-Harness

(1) 6-Pin Video Input Cable

(1) 6-Pin Audio In/Out Cable

(1) C-253 Camera (Bullet Camera)

(1) RGB Input Cable

(1) Instruction Sheet

SAFETY PRECAUTIONS

1. Please read through the entire instruction manual before starting any of the installation procedures.

2. We recommend disconnecting the negative side of the battery until ready to code the vehicle.

3. Do not install any of the main modules near any major components or near the HVAC system,

as placing items near the HVAC may cause damage or overheating to the vehicle or interface.

4. We recommend not disconnecting any of the air bag connections behind the dash panels.

5. This product is under Crux’s 1 year manufacturer’s warranty. Warranty may be voided in the case where

the device shows proof of being opened or improper extreme force.

TECH SERVICES

All our products are manufactured under strict quality control. Each device is being tested before shipment. If nevertheless do occur problems or if

you have technical questions, contact us directly:

Crux Interfacing Solutions Tech Support

1 (855) 822-1348 (Mon - Fri - 9:00 AM - 5:00 PM) Time

www.cruxinterfacing.comRev. 042616 1

8.4” SCREEN (2-PIECE RADIO).

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

INSTALLATION OVERVIEW

www.cruxinterfacing.comRev.042616 2

TO FACTORY

HEADUNIT

22-PIN

(male plug)

VIDEO

INPUTS

RED/ POWER 12V

BLACK/ GROUND

VIDEO

(male plug)

4 5 6 7 8

OFF

1 2 3

22-PIN

(female plug)

LVDS

(T-Harness)

6-PIN

(male plug)

8-PIN

(male plug)

MULTIMEDIA

INTERFACE

TO FACTORY

DISPLAY (Top Unit)

TO FACTORY

HARNESS

CAN

MODULE

*PLEASE TAP 6-PIN CONNECTOR

FOR CAMERA POWER & GROUND

WIRE VIEW

1 2 3

4 5 6

6-PIN WIRE CODES

1. Yellow = Contstant 12V

2. Red = Acc 12V

3. Gray = Ctrl Data

4. Black = Ground

5. Green = Reverse Trigger

6. White = Switch Data

CAMERA IN

VIDEO 1 & 2

INPUTS

DATALINK STATUS

POWER STATUS DATALINK STATUS

POWER STATUS

6-PIN

(male plug)

8-PIN

(male plug)

BULLET

CAMERA

DIP SET

RGB

DATA

PWR

SWITCH

AUDIO

IN/OUT

LVDS

OUT

LVDS

(T-Harness)

4-PIN

(male plug)

6-PIN

(male plug)

RED/ REVERSE TRIGGER INPUT

YELLOW/ CONSTANT INPUT

BLACK/ GROUND INPUT

POWER DOWN

CIRCUIT

CUT HERE

(GREEN/ PIN 5)

TAP THE REVERSE

LAMP SIGNAL

GREEN/ REVERSE OUTPUT

....

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

www.cruxinterfacing.comRev. 042616 3

CONNECTING THE INTERFACE

Follow these steps to properly install the interface module.

Step 1 - Remove the factory radio to gain access to the factory 22-Pin connector.

Located behind the radio, Remove the factory 22-Pin connector.

Step 2 - Using the provided 22-Pin T-Harness, mate both sides of the T-Harness. To the factory harness side, and to the factory radio side.

Also connect the Green LVDS T-Harnesstothe back of the display (Top Unit) and to the factory connector.

4 5 6 7 8

OFF

1 2 3

MULTIMEDIA

INTERFACE

CAN

MODULE

DATALINK STATUS

POWER STATUS D

POWER STATUS

6-PIN

(male plug)

8-PIN

(male plug)

6-PIN

(male plug)

VIDEO

INPUTS

DIP SET

RGB

DATA

PWR

4-PIN

(male plug)

RED/ POWER 12V

BLACK/ GROUND

VIDEO

(male plug)

*PLEASE TAP 6-PIN CONNECTOR

FOR CAMERA POWER & GROUND

WIRE VIEW

1 2 3

4 5 6

6-PIN WIRE CODES

1. Yellow = Contstant 12V

2. Red = Acc 12V

3. Gray = Ctrl Data

4. Black = Ground

5. Green = Reverse Trigger

6. White = Switch Data

CAMERA IN

VIDEO 1 & 2

INPUTS

BULLET

CAMERA

RED/ REVERSE TRIGGER INPUT

YELLOW/ CONSTANT INPUT

BLACK/ GROUND INPUT

POWER DOWN

CIRCUIT

CUTH HERE

(GREEN/ PIN 5)

TAP THE RESERSE

LAMP SIGNAL

GREEN/ REVERSE OUTPUT

....

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

www.cruxinterfacing.comRev. 042616 4

CONNECTING THE INTERFACE

Follow these steps to properly install the interface module.

Step 3 - Connect the 8-Pin connector on the T-Harness to the CAN interface module.

Step 4 - After connecting the module, set the proper dip switches to the “ON” position. Make sure to set the AV sources being used to the

“ON” position. NOTE: The Video In-Motion feature does not require activation. This feature is permanently ON and will not

disturb the navigation GPS performance.

DIP SWITCH DESCRIPTION

IF NOT USING THE INPUT, PLACE TO OFF

DIP 1 = External RGB Enable

DIP 2 = AV1 Enable

DIP 3 = AV2 Enable

DIP 4 = RGB IN (On= 480/OFF= 1080p)

DIP 5 = Rear-View Camera Input Enable

DIP 6 = IR Programming

DIP 7 = Not Used/ Set to OFF

DIP 8 = OFF = 8.4”/ ON = 4.3” Screen

4 5 6 7 8

OFF

1 2 3

MULTIMEDIA

INTERFACE

CAN

MODULE

DATALINK STATUS

POWER STATUS

DATALINK STATUS

POWER STATUS

6-PIN

(male plug)

8-PIN

(male plug)

6-PIN

(male plug)

VIDEO

INPUTS

DIP SET

RGB

DATA

PWR

4-PIN

(male plug)

RED/ POWER 12V

BLACK/ GROUND

VIDEO

(male plug)

*PLEASE TAP 6-PIN CONNECTOR

FOR CAMERA POWER & GROUND

WIRE VIEW

1 2 3

4 5 6

6-PIN WIRE CODES

1. Yellow = Contstant 12V

2. Red = Acc 12V

3. Gray = Ctrl Data

4. Black = Ground

5. Green = Reverse Trigger

6. White = Switch Data

CAMERA IN

VIDEO 1 & 2

INPUTS

BULLET

CAMERA

RED/ REVERSE TRIGGER INPUT

YELLOW/ CONSTANT INPUT

BLACK/ GROUND INPUT

POWER DOWN

CIRCUIT

CUTH HERE

(GREEN/ PIN 5)

TAP THE RESERSE

LAMP SIGNAL

GREEN/ REVERSE OUTPUT

....

After each change of the DIP switch settings,

we recommend powering down the module,

then restarting the vehicle.

LED INDICATORS

DATALINK LED:

Blinking = BUS Detected.

OFF = Power Down/ Sleep mode.

POWER LED:

ON = Power On

OFF = Power OFF

MULTIMEDIA MODULE CAN MODULE

UP=OFF DOWN=ON

DATALINK STATUS

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

www.cruxinterfacing.comRev. 042616 5

CONNECTING THE INTERFACE

Using Side B of the interface (Camera & AV Inputs), connect the interface as described below.

Step 5 - With the T-Harness and LVDS harnesses properly connected, use the 6-Pin harness to connect the smaller interface to

the main interface box.

Step 6 - Connect the large White 6-Pin and the smaller 8-Pin connectors to the main module.

Completing the connections of the two modules. Be sure to CUT the GREEN wire and CONNECT the 6-PIN side of the

GREEN wire to REVERSE.

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

www.cruxinterfacing.comRev. 042616 6

CONNECTING THE AUDIO AND VIDEOINPUTS

In order for the interface to recognize the audio and video inputs, please do the following.

Step 1 - Connect the 6-Pin Video Adaptor to the main interface module. This allows you 3 video inputs.

INPUT DESCRIPTIONS:

YELLOW - VIDEO 1 INPUT

WHITE - VIDEO 2 INPUT

RED - REVERSE CAMERA INPUT

GRAY WIRE - OPTIONAL IR OUTPUT

Step 2 - Connect the 6-Pin Audio Adaptor to the main interface module. This allows you 2 Audio inputs and 1 Audio output.

USING THE MENU BUTTONS

The installer has MENU options available. These buttons are o ered on the bottom side the main interface module.

Step 1 -Use the 3 buttons on the bottom to adjust the following:

Button 1 = Menu

Button 2 = Up (+)

Button 3 = Down (-)

(From left to right)

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

www.cruxinterfacing.comRev. 042616 7

CONTRAST

BRIGHTNESS

SATURATION

POSITION H

POSITION V

IR AV1

IR AV2

GUIDE L

GUIDE R

GUIDE CNTRL

H-SIZE

V-SIZE

(+) (-)

BOTTOM OF THE INTERFACE

OFF

NOTE:

OFF is UP on the DIP Switch

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

www.cruxinterfacing.comRev. 042616 8

SWITCHING AV INPUTS

For the audio to be present from the AV sources, make sure the AUX source is selected on the radio.

The interface also provides you with a optional Switch Button for toggling through the AV inputs.

RADIO TYPE: 4.3”

Press the MORE (+) button on the control center to toggle the inputs.

Compatible radio: 4.3”Screen

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

www.cruxinterfacing.comRev. 042616 9

COMPATIBLE RADIO: 8.4” Screen Radio (2-Piece Radio)

SPECIFICATIONS

Operation voltage 10.5 – 14.8V DC

Stand-by power drain 10mA

Power consumption 4.8W

Temperature range -40°C to +85°C

Weight 190g

Measurements (box only) B x H x T 15.2 x 9 x2.1 cm

SEPARATE CD SLOT

INTERFACING SOLUTIONS

RVCCH-75F

REAR-VIEW CAMERA INTEGRATION

FOR SELECT DODGE,

CHRYSLER & FIAT VEHICLES

www.cruxinterfacing.comRev. 042616 10

HOW TO INSTALL THE BULLET CAMERA

Step 4 . Clean and clear the hole for the camera to be inserted.

Step 5 . Insert the cables and camera through the drilled hole but DO NOT

FULLY INSERT, this will allow you to rotate and camera and position it when

testing the camera view from the 4.3” display in the car.

Step 6 . Route your power and RCA cable towards the front of the vehicle

Step 1 . After you have removed the 3rd brake light from the trunk lid, use

the supplied drilling template to begin drilling the hole on the back side of the

brake light.

Step 2 . Continue drilling through the back and into the front side of that

brake light. This will allow you a guide hole when you begin drilling on the

front side.

Step 3 . Turn over the brake light and continue clearing the hole on the

front side of the brake light. Be very careful when drilling, take your time and

cleanly drill.

Scan the QR code to watch the installation video.

Andere Handbücher für RVCCH-75F

Inhaltsverzeichnis

Andere Crux Autozubehör Handbücher

Crux

Crux AVIGM-04S Bedienungsanleitung

Crux

Crux Sightline VIMCF-93C Bedienungsanleitung

Crux

Crux Sightline PCM-3 Bedienungsanleitung

Crux

Crux RVCAD-81M Gebrauchs- und Pflegehandbuch

Crux

Crux RVCCH-75B Bedienungsanleitung

Crux

Crux RVCGM-80I Bedienungsanleitung

Crux

Crux SWRGM-49 Bedienungsanleitung

Crux

Crux F Series Bedienungsanleitung

Crux

Crux Sightline VIMFD-95F Bedienungsanleitung

Crux

Crux SWRVL-54 Bedienungsanleitung

Crux

Crux Sightline VIMMB-85N Bedienungsanleitung

Crux

Crux Logic ACPBM-77Y Bedienungsanleitung

Crux

Crux VIMGM-94M Bedienungsanleitung

Crux

Crux CFD-03E Bedienungsanleitung

Crux

Crux RVCCH-75D Bedienungsanleitung

Crux

Crux SWRGM-51 Bedienungsanleitung

Crux

Crux VIMBM-86B Bedienungsanleitung

Crux

Crux SWRHN-62L Bedienungsanleitung

Crux

Crux Sightline RVCMB-78S Bedienungsanleitung

Crux

Crux BEECR-35C Bedienungsanleitung

Crux

Crux ACPGM-80N Bedienungsanleitung

Crux

Crux Sightline RVCAD-81B Bedienungsanleitung

Crux

Crux Sightline RVCAD-81 Bedienungsanleitung

Crux

Crux RVCCH-75F Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung