Crux RVCGM-80I Bedienungsanleitung

CHEVROLET GMC

2014 –2017 Avalanche

2014 –2017 Corvette

2014 –2016 Impala

2014 –2016 Silverado

2015 –2016 Suburban

2015 –2016 Tahoe

2015 –2016 Canyon

2014 –2016 Sierra

2014 –2016 Yukon

- OBD2 programming, no need for an interface.

- Plug and Play Connections for ease of use.

- MyLink Radio with 8” colored screen (RPO Codes IO5 and IO6). See page 5 for details.

By using this product, the user agrees to the terms and conditions stated below:

1. Only one (1) license RVC coding is available on the RVCGM-80I.

2. Removal of RVC coding cannot be done using the RVCGM-80I. A Chevrolet dealership can remove

the RVC coding at user’s expense.

3. During the programming process:

- Maintain Battery voltage above 12 volts. (Do not use any accessories)

- Do not disconnect the OBD2-Dongle until the programming process has been completed.

OBD2 Dongle with OBD2 Connector

Video Cable with Female

Crimp Terminals

Rev.112216

1 / 5

OBD-Dongle LED Indicator

The LEDs are located inside the Dongle Module at right side of 8 pin connector.

(LED states last approximately 5 seconds)

BLUE LED

Solid = Normal operation

RED LED

Solid = Invalid operation

Blinking with BLUE LED OFF = License expired

GREEN LED

Solid = RVC Coding successfully

Blinking and BLUE LED OFF = License valid / BLUE

LED ON = diagnostic coding in progress

RED and GREEN LEDs

Solid = CAN Communication Error or Diagnostic session terminated with error.

OBD-Dongle License note

To verify if the OBD-Dongle license has been used or not:

Connect +12V to OBD 2 connector, Pin 4 or Pin 5 to GND

and Pin 16 to +12V.

Observe LED condition, if:

Flashing RED = License expired (Dongle has been used)

Flashing GREEN = Valid License (Dongle has not been used)

Please follow the installation instructions carefully to successfully code the RVC.

1. The OBD2 Port is usually located under steering wheel column.

2. Turn Ignition to the ON position (do not start engine).

3. Turn OFF Head Light to reduce power usage.

4. Turn On radio and wait until it has booted and is ready for normal operation.

5. Plug in the OBD-Dongle into OBD2 port.

6. Wait until the LED lights up to a solid GREEN (the process should be completed in about 10

seconds), then unplug OBD-Dongle from vehicle OBD2 port.

7. Turn Key to OFF, remove the key, open driver door then close, lock the vehicle and wait for

approximately 2 minutes.

LEDs

Rev.112216

2 / 5

8. Unlock the vehicle, open driver door, start the engine and shift to REVERSE Gear. If no

camera has been connected yet, within 20 seconds, the Radio Screen should switch to a Blue

Screen with the message “Service Rear Vision System“. This means that the RVC Coding was

successful. (see screen image on the next page)

9. If the Radio screen does not switch to a Blue Screen, Turn Off vehicle. At HMI-Module,

disconnect the Black 20-Pin connector for about 5 seconds and reconnect. Start the engine

again and shift to Reverse Gear; this should fix the issue.

Repeat steps 6 and 7 if necessary.

HMI Control Module

Coding is successful if a Blue Screen with the message,

“Service Rear Vision System”, appears on the screen

GRAY 12-Pin Connector

BLACK 20-Pin Connector

Rev.112216

3 / 5

Video RCA Cable Connection (Pinout)

Insert the Video RCA cable Camera Signal + to Pin# 5 of the GRAY 20-Pin connector and the

Camera Signal Ground to Pin# 6. See diagram below:

Camera Signal GND

BLACK 20-Pin Connector

GRAY 20-Pin Connector

Camera Signal +

Picture shows the Video RCA Cable

connected to the GRAY 12-Pin HMI

connector. Plug the camera

extension cable to the Yellow RCA.

Rev.112216

4 / 5

Factory HMI Module Location

Camera Connection

Mount the camera (not included) at the rear of the vehicle. Power the camera by tapping the

RED power lead to +12V from the reverse light wire and BLACK to Ground. Run the extension

cable towards the HMI location. Plug in the male YELLOW video RCA to the female RCA of the

RVCGM-80I video cable. Test the camera for functionality.

Compatible Radios

IO5 = MyLink Radio, AM/FM stereo with CD player

IO6 = MyLink Radio with Navigation, AM/FM stereo and CD player

The Regular Production Option (RPO) Code label is located in spare tire well or inside glove

compartment.

HMI Module

Rev.112216

4 / 5

Inhaltsverzeichnis

Andere Crux Autozubehör Handbücher

Crux

Crux Sightline RVCCH-75E Bedienungsanleitung

Crux

Crux RVCMZ-72D Bedienungsanleitung

Crux

Crux ACPBM-77X Bedienungsanleitung

Crux

Crux Sightline RVCAD-81B Bedienungsanleitung

Crux

Crux RVCVL-82S Bedienungsanleitung

Crux

Crux SOOGM-15 Bedienungsanleitung

Crux

Crux BEECR-35D Bedienungsanleitung

Crux

Crux CFD-03E Bedienungsanleitung

Crux

Crux RVCCH-75 Bedienungsanleitung

Crux

Crux SWRHN-62L Bedienungsanleitung

Crux

Crux TDR-RVM32 Bedienungsanleitung

Crux

Crux Sightline RVCAD-81 Bedienungsanleitung

Crux

Crux RVCMZ-72 Bedienungsanleitung

Crux

Crux Sightline RVCVW-73B Bedienungsanleitung

Crux

Crux F Series Bedienungsanleitung

Crux

Crux BEEBG-25 Bedienungsanleitung

Crux

Crux VRFAD-81C Bedienungsanleitung

Crux

Crux DKGM-51 Bedienungsanleitung

Crux

Crux SWRGM-49 Bedienungsanleitung

Crux

Crux RVCAD-81M Gebrauchs- und Pflegehandbuch

Crux

Crux Sightline VIMFD-95 Bedienungsanleitung

Crux

Crux BEECR-35C Bedienungsanleitung

Crux

Crux Sightline VIMCF-93C Bedienungsanleitung

Crux

Crux Sightline RVCVW-73 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung