Crux ACPBM-77X Bedienungsanleitung

Smart-Play

Power/Video Harness

USB Extension Cable Microphone

ACPBM-77X

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5”or 8.8” Monitor) and 10-Pin LVDS Connector

INTERFACING SOLUTIONS

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.0724191 of 12

- Smart-Play Integraon system allows connecon of Android and other devices to the iDrive infotainment system.

- Control Apps using smartphone’s voice control feature or the factory iDrive Knob.

- Adds aermarket rear view camera input.

- Picture-in-picture mode combining aer-market rear-view picture with factory parking sensor graphics.

- Built-in on-screen display and setup.

- 1 trigger output (+12V max. 1A) for the camera power.

NOTE

- Android Phones must have a rmware version of 8 and above.

- For 2007 & up vehicles without a factory AUX input, add on the CRUX AUX-BM4 for audio.

- For 2007 & below vehicles without a factory AUX input, add on the CRUX AUX-BM5 for audio.

PRODUCT FEATURES:

PARTS INCLUDED:

ACPBM-77X Module Power/CAN Harness ACPBM-77X Vehicle Harness

LVDS10 Cable 3.5mm to RCA Adapter Smart-Play Interface Module

1. DO NOT connect the Quadlock Connector to Factory Radio CD Headunit UNLESS the 10 Pin LVDS Cable has

been properly and completely connected to factory display and all the other 10 Pin LVDS cable connections have

been made according to the wiring diagram above or the factory display will be damaged;

2. DO NOT connect the 10 Pin LVDS Cable when the Radio is Powering ON or the factory display will be damaged;

3. When the Radio CD Headunit is active (powered ON ), DO NOT disconnect any of the 10 pin LVDS Connections

or the factory display will be damaged.

WARNING

Setting the DIP switches of the Interface Box.

DIPs 1 and 2 on the back of the interface-box is used to set the monitor size. DIP 3 must be set to OFF.

After each change of the DIP switch settings you have to execute a power reset of the interface box!

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

2 of 12

INSTALLATION DIAGRAM:

INTERFACING SOLUTIONS

ACPBM-77X

DIP SWITCH SETTINGS:

LVDS OUT

LVDS IN

+12V Switching

Output 1 (Pink Wire)

Rear-View

Camera

(Not Included)

10-pin factory

LVDS Cable LVDS10 Cable

Back-Side of Factory

LCD Screen

*If using OEM Back-up

camera, leave REAR CAM

input unoccupied.*

*If installing after-market Back-Up

camera, use the pink wire to provide power to

to the camera, if not, please ignore this connection*

ACPBM-77X

Vehicle Harness

UART

POWER/VIDEO

Smart-Play Module

Vehicle Auxiliary

Input (AUX input)

Female RCA to

3.5mm jack

Male L & R RCA

Outputs (Audio)

AUX

POWER / CAN

FRONT

CAM

REAR

CAM

UPDATE

Smartphone Cable

USB Input

12V Green Output 2

to ACC power

(on Smart-Play Harness)

Power/CAN

Harness

iDrive Knob

Retention Cable

LVDS

OUT

v. 123

Intelligent Solution

ACPBM-77X Module

ACC Power

Ground

Constant

Back of Headunit

See Warning below

Setting the DIP Switches of the VRFBM -77D

DIPs 1 and 2 on the back of the interface box are used to set the monitor type. The default seng is:

Vehicle / N avigation

Dip 1

Dip 2

Dip 3

M-ASK

OFF

No func

CCC

No func

WARNING :

1. DO NOT connect the Quadlock Connector to Factory Radio CD Headunit UNLESS the 10 Pin LVDS Cable has

been properly and completely connected to factory display and all the other 10 Pin LVDS cable connections have

been made according to the wiring diagram above or the factory display will be damaged;

2. DO NOT connect the 10 Pin LVDS Cable when the Radio is Powering ON or the factory display will be damaged;

3. When the Radio CD Headunit is active (powered ON ), DO NOT disconnect any of the 10 pin LVDS Connections

or the factory display will be damaged.

2 / 10

Rev.040816

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

3 of 12

INTERFACING SOLUTIONS

ACPBM-77X

INSTALLATION INSTRUCTIONS:

1. Installaon is done behind the front

panel.

2. Carefully remove the dashboard

front panel using a trim removal tool.

3. Pull out the front panel.

4. Remove the 2 torq screws (T-10)

under the LCD panel’s hood.

5. Remove the two screws bracing the

A/C control panel.

6. Remove the A/C control panel.

7. Remove the LCD screen panel. 8. Unplug the gray LVDS connector

from the back side of the LCD monitor.

9. Plug in the LVDS10 cable in place of

the factory gray LVDS connector.

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

4 of 12

INTERFACING SOLUTIONS

ACPBM-77X

10. Connect both the gray LVDS con-

nector and other end of the LVDS10

cable to the ACPBM-77X module.

11. Remove the two screws bracing the

Headunit.

12. Remove the Headunit and unplug

the Quadlock connector.

13. Unplug the 2-pin ber opc cable

from the factory Quadlock connector.

14. If your vehicle doesn’t come with

an auxiliary audio input, you must get

an Auxiliary Input Interface kit (CRUX

AUX-BM4.

*if your vehicle has factory AUX, skip steps 14-16

15. Remove the 12-pin connector

(wire-side view) from the factory

Quadlock connector. Insert the pins

from the AUX-BM4 harness as follows:

White - Pin 2 / Red - Pin 7 / Black - Pin 8

16. Plug in the OBD coder in to the ve-

hicle’s OBD port to the factory system.

Once the module’s LED turns green,

you can remove the coder.

17. Plug in the 2-pin ber opc

connector previously removed from

the factory Quadlock connector to the

ACPBM-77X harness (Female side).

18. Plug the factory Quadlock connec-

tor in to the male side of the ACPBM-

77X harness.

7 8

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

5 of 12

INTERFACING SOLUTIONS

ACPBM-77X

19. Tap the Black GND wire from the

Smart-Play Power/Video harness to the

black Ground wire on the ACPBM-77X

vehicle harness (Male Side).

20. Tap the Yellow constant wire from

the Smart-Play Power/Video harness to

the Red constant wire on the ACPBM-

77X vehicle harness (Male Side).

21. Connect the male 8-pin connector

from the ACPBM-77X to the female

8-pin connector on the Power/CAN

harness.

22. Tap the RED ACC wire from the

Smart-Play Power/Video harness to the

green +12V output on the ACPBM-77X

harness.

23. Plug in the female side of the

ACPBM-77X harness to the Headunit.

24. Plug the Video Out from the Smart-

Play Power/Video harness into the

FRONT CAM input on the module.

26. If installing an aermarket back-up

camera, plug the camera’s video out

to the REAR CAM input on ACPBM-77X

module. Use the PINK power output 1

wire provided on the Power/CAN har-

ness to power the camera. An image

is displayed in step 26. If retaining an

OEM camera or if you’re not installing

a back-up camera, skip steps 25 and 26.

25. Plug in the Power/CAN harness to

the ACPBM-77X module.

27. Connect the camera power wires to

the PINK power output 1 wire.

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

6 of 12

INTERFACING SOLUTIONS

ACPBM-77X

29. If your vehicle has a factory AUX

input, use the 3.5mm to RCA Adapter

included in the kit to connect sound to

the factory audio system.

28. Connect the audio out RCAs from

the Power/Video harness to the RCA

inputs that were installed earlier.

30. Mount the microphone to a

locaon of your choice.

31. Connect the 3.5mm microphone

jack to the MIC input on the Power/

Video harness.

32. Connect the white wire with the

4-pin connector from the Power/CAN

harness to the UART port on the Smart-

Play module.

33. Connect the Power/Video harness

to the POWER/VIDEO port on the

Smart-Play module.

36. Check the OSD sengs and make

sure they match those on the next

page. Test the Back-Up camera. Put

gear in reverse and check for rear

camera image on screen. Go to Smart-

Play mode and test for funconality.

Once the cameras and Smart-Play

validaon is complete, mount the

ACPBM-77X and Smart-Play modules.

And nally, reinstall all the components

to their original set-up.

34. Connect the USB extenon cable

to the USB input on the Power/

Video harness for easier access when

connecng your smart-phone or USB.

35. Test the communicaon. Turn on

the ignion and check if LEDs are on.

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

7 of 12

INTERFACING SOLUTIONS

ACPBM-77X

OSD Menu

Use the following buons to enter the ACPBM-77X OSD Menu:

BMW

OSD SETTINGS:

To ensure that Smart-Play works, make sure

these input sengs are in eect:

FRONTCAM (FVC) = SmartPhone

To retain the factory Back-Up Camera:

REARCAM (RVC) = OEM

To acvate an aermarket Back-Up Camera:

REARCAM (RVC) = ON

Shift knob to the right for 10 seconds to

enter OSD Menu Use Knob to navigate

menu and make selections

Use knob to navigate Smartplay/ Android

Auto apps and make selections

Hold the menu button to

change the video sources

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.070919

11 of 13

INTERFACING SOLUTIONS

ACPAD-81Y

Smart-Play Integration with Multi Camera Inputs & USB Player

for AUDI Vehicles with MMI MIB/MIB2 Systems

OSD Menu Menu Item

OSD

POS. X 0-xxx

POS. Y 0-xxx

Size Small Small OSD menu window

Large Large OSD menu windows

Osd TimeOut 2-20

Info Version X.XX.XX Displays the current SW-version

Factory Reset

CONNECTING THE SMART-PLAY INTERFACE:

plugged in to the USB port using the smartphone’s OEM charger/data cable. The USB port on the

ACPBM-77X can be used to charge the Apple device or play videos or music from a USB thumb drive.

to the next enabled input. If all inputs are enabled the order is:

Rear CAM > Video Input (Smart-Play) > Repeat ...



ACPBM-77X

To exit the Smart-Play menu, hold the “Menu” button for 3-5 sec.

Switch the vehicle’s audio source to the AUX source. This will allow us to hear the Smart-Play audio



Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

Note:

To exit the back-up camera image,

push down on the iDrive buon

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

8 of 12

INTERFACING SOLUTIONS

ACPBM-77X

Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.070919

12 of 13

INTERFACING SOLUTIONS

ACPAD-81Y

Smart-Play Integration with Multi Camera Inputs & USB Player

for AUDI Vehicles with MMI MIB/MIB2 Systems

1. Picture above shows the HOME screen of the Smart-

with a USB thumb drive plugged in to the USB port.

2. Using the iDrive knob of the vehicle, navigate the

cursor to the Bluetooth icon (scrolling right). Image above

will appears on the screen the BT device name and

pairing code (0000).

device and connect to “CRUX Smart-Play_XXXX”.

4. Once the ACPBM-77X has connected via Bluetooth, it

5. Use the iDrive knob to navigate the cursor to the 6. Image above shows the “Home Screen” once the

smartphone is connected.

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

NOTE:

Make sure the audio source on the factory system is set to AUX mode (not AM/FM/Bluetooth). Also, if your smart-

phone is set to automatically connect to your factory bluetooth, make sure you void the connection. One way is to forget the

device (your vehicle) on your phone. This will avoid Smart-Play connection interferences. If you are using the wireless feature

and notice degraded audio or video quality, switch to the wired alternative, for it is a higher quality connection, unlike bluetooth.

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

9 of 12

INTERFACING SOLUTIONS

ACPBM-77X

Video-In-Motion Function

It is possible to ac�vate and deac�vate the video-in-mo�on in the OSD menu “MISC” (Opera�on of the OSD:

see chapter “OSD-Opera�on”).

OSD-Menu

Menu Item

Setting

Description

MISC VIM

Video-In-Mo�on ac�vated

OFF

Video-In-Mo�on deac�vated

NOTE: The Video-In-Mo�on func�on is permanently ac�ve without disturbing the naviga�on performance.

Selecting the Interface as Current AV Source

BMW 2-Button iDrive Mini 2-Button iDrive

A Long press of the Menu-button will select the interface as current video source.

A Short press of the CD Button or the MENU Button will switch the video sources (cameras or other video

source). Each short press will switch to the next enabled input. If all inputs are enabled the order is:

FRONT CAM



REAR CAM



…

Inputs which are not enabled are skipped.

CCC Navigation Screen

10 / 10

Rev.040816

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

Display sengs for Smart-Play

Adjust brightness, contrast, and saturaon for a more dened image.

To get to the Display menu, scroll to the SETTING icon in

the Smart-Play HOME menu, and select it.

Once in the SETTING menu, scroll to the Display submenu

and adjust the brightness, contrast, and saturaon to

your desired values.

Conguring the Trigger Outputs

You can congure the +12V trigger outputs in the OSD menu under MISC. The PINK wire (12V OUTPUT

1) is Power Out 1 for the cameras and Power Out 2 is for the Smart-Play module.

OSD Menu Menu Item Seng Descripon

Opon

Power Out 1

(PINK)

CAN +12V when the interface is on (red LED on)

ACC +12V when ignion is on

Cam +12V when camera input is acvated

(manually or automacally)

Power Out 2 CAN Smart-Play power on.

OFF Trigger output deacvated

Crux Interfacing Solutions • 21541 Nordhoff Street, Unit C, Chatsworth, CA 91311

phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com

rev.072419

10 of 12

INTERFACING SOLUTIONS

ACPBM-77X

Tip: We recommend for all camera to use power out seng “Cam” and for Smart-Play the power out

seng of “CAN”.

Smart-Play Integration with Rear-View Camera Input for

E Series BMW with CCC Systems (6.5” or 8.8”Monitor) and 10-Pin LVDS Connector

Powerout sengs for Rear Aermarket Camera and Smart-Play

(Use the PINK (12V Output 1) wire to power the Rear camera)

In the OSD Menu under MISC, set “POWEROUT1” to

CAM. And set “POWEROUT2” to CAN

CAM

CAN

Inhaltsverzeichnis

Andere Crux Autozubehör Handbücher

Crux

Crux BEELINE Series Bedienungsanleitung

Crux

Crux RVCCH-75F Bedienungsanleitung

Crux

Crux ACPGM-80N Bedienungsanleitung

Crux

Crux VIMBM-86B Bedienungsanleitung

Crux

Crux SWRHN-62L Bedienungsanleitung

Crux

Crux RVCCH-75 Bedienungsanleitung

Crux

Crux BEECR-35D Bedienungsanleitung

Crux

Crux DKGM-49 Bedienungsanleitung

Crux

Crux F Series Bedienungsanleitung

Crux

Crux Sightline VIMMB-85N Bedienungsanleitung

Crux

Crux WVI-X Bedienungsanleitung

Crux

Crux Sightline VIMFD-95 Bedienungsanleitung

Crux

Crux BTI-ISO Bedienungsanleitung

Crux

Crux RVCCH-75 Bedienungsanleitung

Crux

Crux RVCCH-75 Bedienungsanleitung

Crux

Crux Sightline VIMFD-95F Bedienungsanleitung

Crux

Crux ACPAD-01W Bedienungsanleitung

Crux

Crux Sightline VIMCF-93C Bedienungsanleitung

Crux

Crux BEEBG-25 Bedienungsanleitung

Crux

Crux Sightline PCM-3 Bedienungsanleitung

Crux

Crux Sightline VIMGM-94 Bedienungsanleitung

Crux

Crux Sightline RVCMB-78S Bedienungsanleitung

Crux

Crux Sightline RVCVW-73 Bedienungsanleitung

Crux

Crux TDR-RVM32 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung